Panasonic KX-TS2350RUB / KX-TS2350RUC / KX-TS2350RUH / KX-TS2350RUR / KX-TS2350RUW Service Manual ▷ View online
12 CIRCUIT OPERATIONS
12.1. Telephone Line Interface and Pulse Dial Circuit
When the hook switch SW1 is ON (off-hook), the circuit is closed, and current is supplied to the base of Q2 via the diode bridge
D17 and Q2 is On
D17 and Q2 is On
→
Q1 is ON (OFF-HOOK condition).
Q1 and Q2 are the dial pulse generating circuits, and are driven by the DIALER (IC1), when the DIALER Pin 10 of IC1 is LOW
→
Q2 is OFF and Q1 is OFF (break). If port Pin 10 is HIGH
→
Q2 is ON
→
Q7 is ON
→
Q1 is ON (make).
12.2. Tone Dial Circuit
Function:
The tone dialing circuit consists of a DTMF (Dual Tone Multi Frequency) signal generator (outputted from Pin 25 of the IC1) for
tone dialing, and also a circuit for outputting the signal to line.
tone dialing, and also a circuit for outputting the signal to line.
The DTMF circuit identifies inputs from the 12 keys (1,2,3,4,5,6,7,8,9,0,
and #) by means of a total of seven frequencies, that
is four low frequencies (Low group) and three high frequencies (High group).
Circuit Description:
When a dial key is pressed, a DTMF signal is output from Pin 25 of IC1 as an analog synthetic wave.
The signal flow to the line is as follows.
Pin 25 of IC1
→
Q3
→
R9
→
Q1
→
Tel Line.
The DTMF signal is sent to the line via the following path. Q3 is an amplifier which is used to output the signal to line.
Shown below is the signal flow used to output the DTMF signal from the handset as a monitor tone when a dial key is pressed.
Pin 3 of IC1
→
R24
→
C15
→
Handset Speaker.
The signal combination and frequency corresponding to each dial key is shown on next page.
16
KX-TS2350RUB / KX-TS2350RUC / KX-TS2350RUH / KX-TS2350RUR / KX-TS2350RUW
17
KX-TS2350RUB / KX-TS2350RUC / KX-TS2350RUH / KX-TS2350RUR / KX-TS2350RUW
12.3. Ringer Circuit
Circuit Operation:
The bell signal passes through C1 (R1)
→
pin 21 of IC1 detect the bell signal.
The ring signal is output from Pin 8 of IC1, and its volume is adjusted in 3 steps (H-L-OFF) by SW3 then impressed on the
ceramic sound generator, and so is generated.
ceramic sound generator, and so is generated.
R15, R16 . . . . . . . . . . . . . Bell sensitivity adjustment
Below content (inside ruled line) is information only for service correspondence.
Usually, the default setting is digit 6.
18
KX-TS2350RUB / KX-TS2350RUC / KX-TS2350RUH / KX-TS2350RUR / KX-TS2350RUW
12.4. Power Circuit and Redial Back-up Circuit
Function:
This set is powered from the line. When it is an OFF-HOOK status, Tel Line
→
D17
→
Q1
→
R9
→
Pin 27 of IC1 (to become
the power supply for IC1 speech network).
The voltage from the line is turned into a constant voltage by D2 and then supplied to the IC1, reset circuit.
Through Tel Line
→
R1
→
R3
→
D17
→
R14 to become the power supply for IC1, and the redial Back-up will be done.
19
KX-TS2350RUB / KX-TS2350RUC / KX-TS2350RUH / KX-TS2350RUR / KX-TS2350RUW
Click on the first or last page to see other KX-TS2350RUB / KX-TS2350RUC / KX-TS2350RUH / KX-TS2350RUR / KX-TS2350RUW service manuals if exist.