DOWNLOAD Panasonic KX-TGB210CA / KX-TGB210RU / KX-TGB210UA / KX-TGB212CA / KX-TGB212RU / KX-TGBA20RU Service Manual ↓ Size: 4.53 MB | Pages: 65 in PDF or view online for FREE

ORDER NO. KM41405838CE

Digital Cordless Phone
B: Black Version
W: White Version
1: White (Base) + Pink (Charger) Version
2: Black (Base) + Pastel Blue (Charger) Version
R: Red Version
F: Pastel Blue Version

(CA: for Kazakhstan, Tajikistan, Uzbekistan, Turkmenistan, 
Kyrgyzstan)
(RU: for Russia, Belarus)
(UA: for Ukraine, Armenia, Moldva, Azerbaijan, Georgia)

Model No

Base Unit

Handset

Charger Unit

KX-TGB210
KX-TGB212
KX-TGBA20

1 (TGB210)
1 (TGB210)

1 (TGBA20)
2 (TGBA20)
1 (TGBA20)

1

1

(Charger Unit)

KX-TGBA20

(Handset)

KX-TGB210
(Base Unit)

2

This service information is designed for experienced repair technicians only and is not designed for use by the general 
public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting 
to service a product. Products powered by electricity should be serviced or repaired only by experienced professional 
technicians. Any attempt to service or repair the product or products dealt with in this service information by anyone 
else could result in serious injury or death.

There are special components used in this equipment which are important for safety. These parts are marked by 
in the Schematic Diagrams, Circuit Board Diagrams, Exploded Views and Replacement Parts List. It is essential that 
these cirtical parts should be replaced with manufacturer's specified parts to prevent shock, fire or other hazards.
Do not modify the original design without permission of manufacturer.

If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
When this mark does appear, please read and follow the special instructions described in this manual on the 
use of PbF and how it might be permissible to use Pb solder during service and repair work.

L When you note the serial number, write down all 11 digits. The serial number may be found on the bottom of the unit. 
L The illustrations in this Service Manual may vary slightly from the actual product.

3

PAGE

PAGE

1 Safety Precautions----------------------------------------------- 5

1.1. For Service Technicians --------------------------------- 5

2 Warning -------------------------------------------------------------- 5

2.1. Battery Caution--------------------------------------------- 5
2.2. About Lead Free Solder (PbF: Pb free)-------------- 5

2.2.1. Suggested PbF Solder ------------------------------ 6

2.3. Discarding of P.C. Board--------------------------------- 6

3 Specifications ----------------------------------------------------- 7
4 Technical Descriptions ----------------------------------------- 8

4.1. Block Diagram (Base Unit) ------------------------------ 8
4.2. Circuit Operation (Base Unit) --------------------------- 9

4.2.1. Outline --------------------------------------------------- 9
4.2.2. Power Supply Circuit--------------------------------- 9
4.2.3. Telephone Line Interface---------------------------10
4.2.4. Transmitter/Receiver--------------------------------10
4.2.5. Pulse Dialling -----------------------------------------10

4.3. Block Diagram (Handset)-------------------------------11
4.4. Circuit Operation (Handset)----------------------------12

4.4.1. Outline --------------------------------------------------12
4.4.2. Power Supply Circuit/Reset Circuit--------------12
4.4.3. Charge Circuit ----------------------------------------12
4.4.4. Battery Low/Power Down Detector--------------12

4.5. Signal Route -----------------------------------------------13

5 Location of Controls and Components ------------------14
6 Installation Instructions ---------------------------------------14
7 Operating Instructions-----------------------------------------14

7.1. For Service Hint-------------------------------------------14

8 Service Mode -----------------------------------------------------15

8.1. Engineering Mode ----------------------------------------15

8.1.1. Base Unit ----------------------------------------------15
8.1.2. Handset ------------------------------------------------17

9 Troubleshooting Guide ----------------------------------------19

9.1. Troubleshooting Flowchart -----------------------------19

9.1.1. Check Power------------------------------------------20
9.1.2. Check Battery Charge ------------------------------21
9.1.3. Check Link---------------------------------------------22
9.1.4. Check Handset Transmission --------------------24
9.1.5. Check Handset Reception-------------------------24
9.1.6. Check Caller ID --------------------------------------24
9.1.7. Bell Reception ----------------------------------------24

9.2. Troubleshooting by Symptom (Base Unit) ---------25

9.2.1. Check Point (Base Unit) ---------------------------25

9.3. Troubleshooting by Symptom (Handset) -----------28

9.3.1. Check Point (Handset) -----------------------------28

10 Disassembly and Assembly Instructions ---------------31

10.1. Disassembly Instructions -------------------------------31

10.1.1. Base Unit ----------------------------------------------31
10.1.2. Handset ------------------------------------------------32
10.1.3. Charger Unit ------------------------------------------33

10.2. How to Replace the Handset LCD -------------------34

11 Measurements and Adjustments---------------------------35

11.1. The Setting Method of JIG (Base Unit) -------------35

11.1.1. Preparation --------------------------------------------35
11.1.2. PC Setting ---------------------------------------------35

11.2. Adjustment Standard (Base Unit)---------------------37

11.2.1. Bottom View-------------------------------------------37

11.3. The Setting Method of JIG (Handset) ---------------38

11.3.1. Preparation --------------------------------------------38

11.3.2. PC Setting--------------------------------------------- 38

11.4. Adjustment Standard (Handset) ---------------------- 40

11.4.1. Component View ------------------------------------ 40

11.5. Things to Do after Replacing IC  --------------------- 41

11.5.1. Base Unit ---------------------------------------------- 41
11.5.2. Handset------------------------------------------------ 41

11.6. RF Specification ------------------------------------------ 42

11.6.1. Base Unit ---------------------------------------------- 42
11.6.2. Handset------------------------------------------------ 42

11.7. How to Check the Handset Speaker or

Receiver ---------------------------------------------------- 43

11.8. Frequency Table (MHz)--------------------------------- 43

12 Miscellaneous---------------------------------------------------- 44

12.1. How to Replace the Flat Package IC --------------- 44

12.1.1. Preparation-------------------------------------------- 44
12.1.2. How to Remove the IC----------------------------- 44
12.1.3. How to Install the IC -------------------------------- 45
12.1.4. How to Remove a Solder Bridge ---------------- 45

12.2. How to Replace the Shield Case--------------------- 46

12.2.1. Preparation-------------------------------------------- 46
12.2.2. Caution------------------------------------------------- 46
12.2.3. How to Remove the Shield Case---------------- 46
12.2.4. How to Install the Shield Case ------------------- 47

12.3. Terminal Guide of the ICs, Transistors, Diodes

and Electrolytic Capacitors ---------------------------- 48

12.3.1. Base Unit ---------------------------------------------- 48
12.3.2. Handset------------------------------------------------ 48

13 Schematic Diagram -------------------------------------------- 49

13.1. For Schematic Diagram -------------------------------- 49

13.1.1. Base Unit (Schematic Diagram (Base

Unit))---------------------------------------------------- 49

13.1.2. Handset (Schematic Diagram (Handset))----- 49
13.1.3. Charger Unit (Schematic Diagram

(Charger Unit)) --------------------------------------- 49

13.2. Schematic Diagram (Base Unit)---------------------- 50
13.3. Schematic Diagram (Handset)------------------------ 51
13.4. Schematic Diagram (Charger Unit)------------------ 52

14 Printed Circuit Board ------------------------------------------ 53

14.1. Circuit Board (Base Unit)------------------------------- 53

14.1.1. Component View ------------------------------------ 53
14.1.2. Bottom View ------------------------------------------ 54

14.2. Circuit Board (Handset) -------------------------------- 55

14.2.1. Component View ------------------------------------ 55
14.2.2. Bottom View ------------------------------------------ 56

14.3. Circuit Board (Charger Unit)--------------------------- 57

14.3.1. Component View ------------------------------------ 57
14.3.2. Bottom View ------------------------------------------ 57

15 Exploded View and Replacement Parts List ----------- 58

15.1. Cabinet and Electrical Parts (Base Unit) ----------- 58
15.2. Cabinet and Electrical Parts (Handset)------------- 59
15.3. Cabinet and Electrical Parts (Charger Unit) ------- 60
15.4. Accessories------------------------------------------------ 61
15.5. Replacement Part List ---------------------------------- 62

15.5.1. Base Unit ---------------------------------------------- 62
15.5.2. Handset------------------------------------------------ 63
15.5.3. Charger Unit ------------------------------------------ 64
15.5.4. Accessories------------------------------------------- 65
15.5.5. Screws ------------------------------------------------- 65

4

15.5.6. Fixtures and Tools----------------------------------- 65