DOWNLOAD Panasonic KX-TG8021UAC / KX-TG8021UAS / KX-TG8021UAT / KX-TGA800RUC / KX-TGA800RUS / KX-TGA800RUT Service Manual ↓ Size: 2.47 MB | Pages: 103 in PDF or view online for FREE

53

(K)* Frequency Offset Confir-

mation

-

Follow steps 1 to 3 of (I).

4.Confirm that the frequency Offset is < ± 20 kHz.

IC1, 

R801~R806, 
C808~C814, 
C819, C825, 

C834, IC801, 

L802~L804, 

D801, R807, 

L801, C820, 

C822, C826, 
C827, C832, 
C833, C837, 

D802, DA1,

C117, C124,

C186, C187,
C802~C804,

R107, R108

(L)* Frequency Drift Confir-

mation

-

Follow steps 1 to 3 of (I).

4.Confirm that the frequency Drift is < ± 30KHz/msec.

IC1, 

R801~R806, 
C808~C814, 
C819, C825, 

C834, IC801, 

L802~L804, 

D801, R807, 

L801, C820, 

C822, C826, 
C827, C832, 
C833, C837, 

D802, DA1,

C117, C124,

C186, C187,
C802~C804,

R107, R108

(M)*

Sensitivity Receiver 

Confirmation

-

Follow steps 1 to 3 of (I).

4.Set DECT tester power to -88 dBm.
5.Confirm that the BER is < 1000 ppm.

IC1, 

R801~R806, 
C808~C814, 
C819, C825, 

C834, IC801, 

L802~L804, 

D801, R807, 

L801, C820, 

C822, C826, 
C827, C832, 
C833, C837, 

D802, DA1,

C117, C124,

C186, C187,
C802~C804,

R107, R108

(N)* Power RAMP Confirma-

tion

-

Follow steps 1 to 3 of (I).

4.Confirm that Power RAMP is matching.

IC1, 

R801~R806, 
C808~C814, 
C819, C825, 

C834, IC801, 

L802~L804, 

D801, R807, 

L801, C820, 

C822, C826, 
C827, C832, 
C833, C837, 

D802, DA1,

C117, C124,

C186, C187,
C802~C804,

R107, R108

Items

Check 

Point

Procedure

Check or 

Replace Parts

54

When the customer’s telephone line corresponds to the following conditions, and the transmission signal of SP-Phone is inter-
rupted, performing the next set up to a cordless handset will improve it to some extent.
Conditions

1. When customer’s line has less line loss.

ex.) The customer is using optical fiber, ISDN terminal adaptor, or PBX.
In this case, receiving signal is strong and it may affect transmission signal.

2. When the other party is talking from noisy place.

ex.) The other party is using cellular phone. The background noise is very loud.
In this case, the noise from the other party (i.e. surrounding noise) may affect transmission signal.

• Change the handset address of EEPROM (0129) from 00 to 01 by Engineering Mode.

(O) Audio Check and Confir-

mation

-

1. Link to BASE which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 40 mA.
3. Input -45 dBm/1KHz to MIC and measure Line output level.
4. Confirm that the level is -10 dBm ± 2 dBm and that the distortion level is < 5%

at TEL Line (600 

Ω Load).

5. Input -20 dBm/1KHz to Line I/F and measure Receiving level at REV+ and

REV-.

6. Confirm that the level is -21 dBm ± 2 dBm and that the distortion level is < 5%

at Receiver. (vol = 2)

IC1, R23, C12, 

D21, D22, 
C96, C97, 

R27, RA4, 

C11, C13, 

R28, D3, D4, 

R320, R321, 

MIC

(P) SP phone Audio Check 

and Confirmation

-

1. Link to Base which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 40 mA.
3. Set the handset off-hook using SP-Phone key.
4. Input -25 dBm/1KHz to Line I/F and measure Receiving level at SP+ and SP-.
5. Confirm that the level is -13 dBm ± 2 dBm and that the distortion level is < 5%.

(vol = 3)

IC1, R23, C12, 

C73, D13, 

D14, R152, 
C80, R320, 
R321, MIC, 

C11, C13, 

RA4, R27, 

R28, C72, 

D3, D4

(Q) Charge Pump 2.5V Sup-

ply Confirmation

CP2.5V

1. Confirm that the voltage between testpoint CP2.5V and GND is 2.5V -0.1/

+0.3V.

C52, C53, C49

Items

Check 

Point

Procedure

Check or 

Replace Parts

55

56