DOWNLOAD Panasonic KX-TG7331CAM / KX-TG7331CAT / KX-TGA731RUM / KX-TGA731RUT / KX-TGA731RUC / KX-TGA731RUS Service Manual ↓ Size: 2.85 MB | Pages: 102 in PDF or view online for FREE

41

(*1) Refer to Adjustment Standard (Base Unit) (P.59)
(*2) Refer to Adjustment Standard (Handset) (P.63)

No.

Item

BU (Base Unit) Check

HS (Handset) Check

1

Link Confirmation Normal

HS, BU Mode: [Normal mode]

1. Register Regular HS to BU (to be 

checked).

2. Press [Talk] key of the Regular HS to 

establish link.

1. Register HS (to be checked) to Regular 

BU.

2. Press [Talk] key of the HS to establish link.

2

X’tal Frequency confirmation

1. Check X’tal Frequency. (*1)

(10.368 MHz ± 100 Hz)

1. Check X’tal Frequency. (*2)

(10.368 MHz ±100 Hz)

3

Range Confirmation Normal

HS, BU Mode: [Normal mode]

1. Register Regular HS to BU (to be 

checked).

2. Press [Talk] key of the Regular HS to 

establish link.

3. Compare the range of the BU (being 

checked) with that of the Regular BU.

1. Register HS (to be checked) to Regular 

BU.

2. Press [Talk] key of the HS to establish link.
3. Compare the range of the HS (being 

checked) with that of the Regular HS.

42

Signal Route (P.14)

How to Check the Speaker or Receiver (P.67).
Signal Route (P.14)

Signal Route (P.14)

43

Telephone Line Interface (P.10)
Check Link (P.35)
How to Check the Speaker or Receiver (P.67)

44

If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester
(*1) or not. 

(*1) A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic
level in detail.
(*2) Refer to Check Point (Base Unit) (P.44)

Please follow the items below when BBIC or EEPROM is replaced.

After the measuring, suck up the solder of TP.
*: PC Setting (P.57) is required beforehand.
The connections of simulator equipments are as shown in Adjustment Standard (Base Unit) (P.59).

Items

Check 

Point

Procedure

Check or 

Replace Parts

(A) 3.0 V Supply Confirma-

tion

VDD3

1. Confirm that the voltage between test point VDD3 and GND is 3.0 V ± 0.2 V.

IC1, C50, C51, 

C52, R50, R51, 

C53, F1, D1

(B) 1.8 V Supply Confirma-

tion

VDD1

1. Confirm that the voltage between test point VDD1 and GND is 1.8 V ± 0.1 V. 

Q8, C55, C61, 

C64,  IC7

(C) Charge Pump

2.5 V Supply Confirma-
tion

VDD5

1. Confirm that the voltage between test point VDD5 and GND is 2.5 V  -0.1/+0.3

V. 

IC7, C404

(D) Charge Pump

3.0 V Supply Confirma-
tion

VDD4

1. Confirm that the voltage between test point VDD4 and GND is 3.0 V ± 0.2 V.  IC7, C422, C425

(E)*

BBIC Confirmation

-

1. BBIC Confirmation (Execute the command “getchk”).
2. Confirm the returned checksum value.

Connection of checksum value and program number is shown below.

IC7, X1, R76, 

R69, R70

(F)* EEPROM Confirmation

-

1. EEP-ROM Confirmation (Execute the command “ChkTG7330XXrevYY.bat”).

XX: country code
YY: revision number

2. Confirm the returned checksum value.
3. The checksum is displayed in the last output line.

“XX”, “YY”, and “checksum” vary depending on the country version. You can find
them in the batch file, PQZZ- mentioned in JIG and PC (P.57).

IC7, RA401, 

C401, R405, 

IC401

(G)* BBIC Clock Adjustment

CLK

VDD4

1. Input Command “ sendchar WWD ff 48 IC 8006”
2. Confirm that the voltage between testpoint VDD4 and GND is less than 1.0 V.
3. Input Command “ sendchar sfr”, then you can confirm the current value.
4. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
5. If the frequency is not 10.368MHz ± 100Hz, adjust the frequency of CLK exe-

cuting the command “sendchar sfr xx xx (where xx is the value)” so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.

X1, IC7, C66