Panasonic KX-TG6621RUB / KX-TG6621RUM / KX-TG6621UAB / KX-TG6621UAM / KX-TG6621CAB / KX-TG6621CAM / KX-TG6622CAB / KX-TGA661RUB / KX-TGA661RUM Service Manual ▷ View online
45
KX-TG6621RU/KX-TG6621UA/KX-TG6621CA/KX-TG6622CA/KX-TGA661RU
ԝ
Remove the 2 screws to
remove the operational P.C. board.
remove the operational P.C. board.
Operational P.C. board
ԝ
2 screws
Ԝ
Remove the parallel wire and screw to remove
the main P.C. board.
the main P.C. board.
Ԝ
Parallel wire
Main P.C. board
Ԝ
screw
ԛ
Remove the screw to remove the jack holder.
ԛ
screw
Jack holder
46
KX-TG6621RU/KX-TG6621UA/KX-TG6621CA/KX-TG6622CA/KX-TGA661RU
10.1.2. Handset
Ԙ
Remove the 2 screws.
ԙ
Insert a plastic card.
(Ex. Used SIM card etc.)
between the cabinet body
and the cabinet cover, then
pull it along the gap to open
the cabinet.
(Ex. Used SIM card etc.)
between the cabinet body
and the cabinet cover, then
pull it along the gap to open
the cabinet.
Ԛ
Likewise, open the other
side of the cabinet.
side of the cabinet.
ԛ
Remove the cabinet cover
by pushing it upward.
by pushing it upward.
Ԝ
Remove the solders and tape.
ԝ
ԝ
Remove the screw to remove
the main P. C. board.
the main P. C. board.
Main P.C. board
Ԝ
Screw
Cabinet cover
Cabinet body
Cabinet cover
2 screws
Ԙ
Solders and
Tape
Tape
47
KX-TG6621RU/KX-TG6621UA/KX-TG6621CA/KX-TG6622CA/KX-TGA661RU
10.1.3. Charger Unit
Ԙ
Remove the screw to remove
the cabinet cover.
the cabinet cover.
Ԛ
Remove the solders to remove
the 2 charge terminals.
the 2 charge terminals.
Ԙ
Screw
Ԛ
Solders
Main P.C. board
2 charge terminals
ԙ
Insert a plastic card. (Ex. Used SIM card etc.)
between the cabinet body
and the cabinet cover, then
pull it along the gap to open
the cabinet.
and the cabinet cover, then
pull it along the gap to open
the cabinet.
Cabinet cover
Cabinet body
ԙ
Plastic card
48
KX-TG6621RU/KX-TG6621UA/KX-TG6621CA/KX-TG6622CA/KX-TGA661RU
10.2. How to Replace the Base Unit LCD
Ԙ
ԙ
Fit the heatseal of a new LCD.
Rubber of Soldering Iron
(Part No. PQZZ430PRB)
(Part No. PQZZ430PRB)
Tip of Soldering Iron
(Part No. PQZZ430PIR)
Heatweld with the tip of the soldering
iron about 5 to 8 seconds
(in case of 60W soldering iron).
iron about 5 to 8 seconds
(in case of 60W soldering iron).
New LCD
Operational P.C.B.
0.2mm
0.2mm
If interval tolerance between center lines
is less than 0.2 mm, it is o.k.
is less than 0.2 mm, it is o.k.
Horizontal Interval
Tolerance
Tolerance
Vertical Interval
Tolerance
Tolerance
OK
NG
NG
NG
(Horizontal interval tolerance is
more than 0.2 mm.)
more than 0.2 mm.)
(Vertical interval tolerance is
more than 0.2 mm.)
more than 0.2 mm.)
(Inclined)
Click on the first or last page to see other KX-TG6621RUB / KX-TG6621RUM / KX-TG6621UAB / KX-TG6621UAM / KX-TG6621CAB / KX-TG6621CAM / KX-TG6622CAB / KX-TGA661RUB / KX-TGA661RUM service manuals if exist.