DOWNLOAD Panasonic KX-TG6541RUB / KX-TGA651RUB / KX-TGA405RUB Service Manual ↓ Size: 3.09 MB | Pages: 104 in PDF or view online for FREE

37

Refer to Commands (P.55)

Item

RE (Range Extender) Check

Range Confirmation TX TEST
(TX Power check)

HS, setting
Checked unit: Low TX power (*1)
Regular unit: High TX power (*1)

1. Register Regular HS and RE (to be checked) to Regular BU.
2. HS is power ON with “1“, “6“and “#“.
3. Set TX Power of the RE and the Regular HS according to CHART1.
4. At distance of about 20m between HS and RE,

Link OK = TX Power of the RE is OK.
No Link = TX Power of the RE is NG.

Range Confirmation RX TEST
(RX sensitivity check)

HS, BU setting
Checked unit: High TX power (*1)
Regular unit: Low TX power (*1)

1. Register Regular HS and RE (to be checked) to Regular BU.
2. HS is power ON with “1“, “6“and “#“.
3. Set TX Power of the RE and the Regular HS according to CHART1.
4. At distance of about 15cm between BU and RE,
5. At distance of about 20m between HS and RE,

Link OK= RX Sensitivity of the RE is OK.
No Link = RX Sensitivity of the RE is NG.

RE (to be checked)

TX Power

RE(Range Extender) TX Power Check

Low

RE(Range Extender) RX Sensitivity Check

High

38

Signal Route (P.17)

How to Check the Handset Speaker or Receiver (P.67).
Signal Route (P.17)

Signal Route (P.17)

39

Telephone Line Interface (P.10)
Check Link (P.30)
How to Check the Handset Speaker or Receiver (P.67)

Power Supply Circuit (P.9)

(*1) When replacing FLASH MEMORY (IC421), TAM data need to be written to it. Refer to Base Unit of Things to Do after
Replacing IC or X'tal (P.63)

40

If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester
(*1) or not. 

(*1) A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic
level in detail.
(*2) Refer to Check Point (Base Unit) (P.40)

Please follow the items below when BBIC or EEPROM or FLASH is replaced.

After the measuring, suck up the solder of TP.
*: The Setting Method of JIG (Base Unit) (P.54) is required beforehand.
The connections of simulator equipment are as shown in Adjustment Standard (Base Unit) (P.56).

Items

Check 

Point

Procedure

Check or 

Replace Parts

(A) 3.0 V Supply Confirma-

tion

VDD3

1. Confirm that the voltage between test point VDD3 and GND is 3.0 V ± 0.2 V.

IC2, IC3, C32, 

C36, C86, C87, 
C88, R91, R92, 
R93, R95, D10, 

Q10, L3

(B) 1.8 V Supply Confirma-

tion

VDD1

1. Confirm that the voltage between test point VDD1 and GND is 1.8 V ± 0.02 V.
2. Execute the command “VDD”, then check the current value.
3. Adjust the 1.8V voltage of VDD1 executing command “VDD XX“(XX is the

value).

Q8, C75, C614, 

C61, IC7

(C) Charge Pump

2.5V Supply Confirma-
tion

VDD5

1. Confirm that the voltage between test point VDD5 and GND is 2.5 V -0.1/+0.3

V. 

IC7,C625,C631

(D) Charge Pump

3.0V Supply Confirma-
tion

VDD4

1. Confirm that the voltage between test point VDD4 and GND is 3.0 V ± 0.2 V.  IC7,C616,C630

(E)*

BBIC Confirmation

-

1. BBIC Confirmation (Execute the command “getchk”).
2. Confirm the returned checksum value.

Connection of checksum value and program number is shown below.

IC7, X1, R77, 

RA80

(F)* EEPROM Confirmation

-

1. EEP-ROM Confirmation (Execute the command "sendchar EPV").
2. Confirm the returned Value. (Value for reference is written at "EEPROM C/

SUM” in Software_Version_Table.xls).

IC7, RA402, 

C51, R657, 

IC401

(G)* BBIC Clock Adjustment

CLK

1. Input Command “ sendchar WWD ff 48 IC 8006”
2. Confirm that the voltage between testpoint VDD4 and GND is less than 1.0 V.
3. Input Command “ sendchar sfr”, then you can confirm the current value.
4. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
5. If the frequency is not 10.368MHz ± 100Hz, adjust the frequency of CLK exe-

cuting the command “sendchar sfr xx xx (where xx is the value)” so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.

X1, IC7, R430, 

C305