DOWNLOAD Panasonic KX-TG5521CAB / KX-TGA551RUB (serv.man2) Service Manual ↓ Size: 2.92 MB | Pages: 88 in PDF or view online for FREE

16

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Items

Contents

Battery

You could use other rechargeable batteries sold in a market, but the unit is not guaranteed to work 
properly.

The battery strength may not be indicated correctly if the battery is disconnected and connected again, 
even after it is fully charged. In that case, by recharging the battery as mentioned in the Operating  
Instructions, you will get a correct indication of the battery strength.

PIN Code

Change the PIN using the following method.

8 i {#}{1}{3}{2}

{*}{7}{0}{0}{0}

Enter the new 4-digit base unit PIN. 

i M i {ic}

17

2).   Press         .

1).   Register a Handset to a Base Unit. (*1)

3).   Select "Initial Setup" using      or     
       then press         or 

{>}

.

     

Make sure the address on LCD is correct when entering new data. Otherwise, you may ruin the unit.

{^} {V}

5).   Enter "7", "2", "6", "2", "7", "6", "6", "4".

       Note: 7262 7664 = PANA SONI 

                (see letters printed on dial keys)

7).   Enter "

٨

", "

٨

", "

٨

", "

٨

" (Address). (*2)

9).   Press         , a long confirmation beep 

       will be heard. 

10).   Press              (off) to return to standby mode.

          After that, turn the base unit power off and then power on. 

8).   Enter "

㧖", "㧖" (New Data). (*2)

6).   Select "Write EEP" using      or     
       then press         or 

{>}

.

{^} {V}

Default Data

New Data

M

^

V

M

^

V

M

M

Service Mode

 Read EEP

 

Write EEP

Set Addr.:

_ _ _ _   _ _

Set Addr.:

Set Addr.:

M

M

8

M

M

M

^

V

4).   Select "Line Setup" using      or     
       then press         or 

{>}

.

{^} {V}

M

{C} (Talk)

{s} (Speakerphone)

{ic} (Off/Power)

{ECO/R}

 Navigator

18

ex.)

(*1) Refer to Registering a Handset to a Base Unit in the Operating Instructions.
(*2) When you enter the address or New Data, please refer to the table below.

(*3)

C-ID (FSK) sensitivity

048B

00

01 (6 dB up)

02 (12 dB up) When hex changes from “00” to “01” or “02”,

gain increases by 6 dB or 12 dB.

Frequency

00 08/00 07

02/70

-

-

Use these items in a READ-ONLY mode to
confirm the contents. Careless rewriting may
cause serious damage to the computer system.

ID

00 02~00 06

Given value

-

-

Bell length

02 18

32 (5sec) (*3)

1E (3 sec)

14 (2 sec)

This is time until bell stops ringing.
(Unit: 100 ms)

PULSE Dial speed
(10PPS -> 20PPS)

01 F8

28 (40msec) 

(*3)

14 (20msec)

-

This is pulse make time. (Unit:1 ms)

01 F9

3C (60msec) 

(*3)

1E (30msec)

-

This is pulse break time. (Unit:1 ms)

02 07

57 (870msec) 

(*3)

2C (440msec)

-

This is inter-digit time in pulse mode.
 (Unit:10 ms)

0

0

A

[R]  +  0

1

1

B

[R]  +  1

.

.

C

[R]  +  2

.

.

D

[R]  +  3

.

.

E

[R]  +  4

9

9

F

[R]  +  5

Bell length

32(hex) = 50(dec) 

→ 50 × 100 msec = 5000 msec (5 sec)

PULSE Dial speed
(10PPS -> 20PPS)

28(hex) = 40(dec) 

→ 40 × 1msec = 40msec

3C(hex) = 60(dec) 

→ 60 × 1msec = 60msec

57(hex) = 87(dec) 

→ 87 × 10msec = 870msec

19

     

Make sure the address on LCD is correct when entering new data. Otherwise, you may ruin the unit.

1).   Press         .

2).   Select "Initial Setup" using      or     
       then press          or 

{>}

.

{^}  {V}

3).   Enter "7", "2", "6", "2", "7", "6", "6", "4".

       Note: 7262 7664 = PANA SONI 

                (see letters printed on dial keys)

5).   Enter "

٨

", "

٨

", "

٨

", "

٨

" (Address). (*1)  

7).   Press        , a long confirmation beep

       will be heard. 

8).   Press           (off) to return to standby mode.

          After that, remove and reinsert the batteries. Press the Power button for 
          about 1 second if the power is not turned on. 

6).   Enter "

㧖", "㧖" (New Data). (*1)

4).   Select "Write EEP" using      or     
       then press          or 

{>}

.

{^}  {V}

M

M

Default Data

New Data

M

M

M

M

^

V

M

^

V

^

V

Service Mode

 Read EEP

 

Write EEP

Set Addr.:

_ _ _ _   _ _

Set Addr.:

Set Addr.:

8

M

M

M

M

{C} (Talk)

{s} (Speakerphone)

{ic} (Off/Power)

{ECO/R}

 Navigator