DOWNLOAD Panasonic KX-TG2560B / KX-TG2560S Service Manual ↓ Size: 2.68 MB | Pages: 69 in PDF or view online for FREE

5

A second call is received during a conversation.

       or         was pressed while the handset was on the base unit. Lift the handset and press
       or         again.

When trying to store an item or Caller List information in the directory, the directory memory
is full.

This is a name from the directory. The stored name and phone number are displayed.

NANCY BROWN
1-000-222-3333
---- Waiting ----

Please lift up
and try again

Memory is full

Ann
1234567890

6

This connection is for
U.S.A. version only.

Refer to the simplified
manual (cover) for
Canada or other areas.

 • USE ONLY WITH Panasonic AC ADAPTOR PQLV10Z.
 • The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)
 • If you unit is connected to a PBX which does not support Callrer ID service, you cannot access those services.

This unit will not function during a power failure. To connect a standard telephone on the same line, use the
Panasonic T-adaptor KX-J66.

Telephone Line Cord

Raise the antennas.

Power Outlet
(AC 120 V, 60 Hz)

Single-Line Telephone 
Jack (RJ11C)

Hook

Fasten the AC adaptor cord to 
prevent it from being 
disconnected.

AC Adaptor

T-Adaptor (KX-J66)

Single-Line 
Telephone Jack

Telephone 
Line Cord

Standard Telephone

7

Pressing  CALL WAIT/FLASH  allows you to use special features of your
host PBX such as transferring an extension call or accessing special
telephone services (optional) such as call waiting.

The flash time depends on your telephone exchange or host PBX. You can
select from flash times (call waiting times): "700, 600, 400, 300, 250, 110, 
100 or 90ms (milliseconds)", using the handset near the base unit. 
Your phone comes from the factory set to (call waiting times) "700 ms".
Make sure that the unit is in the stand-by mode.

Press  FUNCTION/EDIT  .

Press      or      repeatedly until the arrow
points to "

Program

".

Press OK      (

Yes

 key).

Press      or      repeatedly until the arrow
points to "

Set flash time

".

Press OK      (

Yes

 key).

Press      or      repeatedly until the desired
time is displayed.

Press OK      (

Save

 key.)

  A beep sounds.
  The display will return to step 4. To return to the stand-by mode,
  press  EXIT/CH  .

1

2

3

4

5

6

7

You can exit the programming mode any time by pressing  EXIT/CH  .
If 3 beeps sound and the display shows "

Save error

", move closer to

the base unit and try again. If "

Save error

" is still displayed, place the

handset on the base unit. Start again from step1.
If you are connected via a PBX, a longer flash time may be necessary to
use PBX functions (transferring a call etc.). Consult your PBX supplier for
the correct setting.

Ringer volume
Program
        OK=Yes

Save directory
Set flash time
        OK=Yes

Flash time
        :700ms
       OK=Save

8

Fig.

1

2

3

4

5

6

To remove

Lower Cabinet

Main P.C. Board

ANT (2.4GHz, 900M)

Battery Cover

Rear Cabinet

Antenna

Main P.C. Board

Screws (3X16) ...................................

Remove the P.C.Board

Screws (3X8) ..................................

Remove the Battery Cover

Screws (2.6X12) ................................

Screws (2.6X12) ................................

Screws (2X5) ................................

(A)X4

(B)X2

(C)X2

(D)X1

(E)X6

Remove     .