Panasonic KX-TG2511CAM / KX-TG2511CAS / KX-TG2511CAT / KX-TG2512CAM / KX-TG2512CAT / KX-TGA250RUM / KX-TGA250RUS / KX-TGA250RUT Service Manual ▷ View online
5
KX-TG2511CA/KX-TG2512CA/KX-TGA250RU
2.2.1.
Suggested PbF Solder
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3 mm, 0.6 mm and 1.0 mm.
(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s
specific instructions for the melting points of their products and any precautions for using their product with other materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3 mm, 0.6 mm and 1.0 mm.
2.3.
Discarding of P.C. Board
When discarding P. C. Board, delete all personal information such as telephone directory and caller list or scrap P. C. Board.
6
KX-TG2511CA/KX-TG2512CA/KX-TGA250RU
3 Specifications
Note:
• Design and specifications are subject to change without notice.
Note for Service:
• Operation range: Up to 300 m outdoors, Up to 50 m indoors, depending on the condition.
• Analog telephone connection: Telephone Line
• Analog telephone connection: Telephone Line
7
KX-TG2511CA/KX-TG2512CA/KX-TGA250RU
4 Technical Descriptions
4.1.
Block Diagram (Base Unit)
Analog
Front
End
T
o TEL_LINE
Bridge
Rect
D3D3
Hook Switch
Q4,Q5
Audio
Bell/Caller ID
Interface
CPU
18
16
23
20
21
19
24
BELL
HOOK
Off-Hook Line Voltage
25
A/D
D/A
ADPCM
Codec Filter
DSP
Speech Encoding
Speech Decoding
BMC
Burst Encoding
Burst Decoding
RF
PLL
5
3
77
75
9
10
EEPROM
SCL
SDA
57
58
44
Charge
Detector
(Optional)
BBIC
IC401
IC7
KX-TG2511/2512 BLOCK DIAGRAM
(BASE UNIT)
MOD/DEMOD
Charge
Pump
43
2.5V
X
T
A
L
X
1
X1
10.3
68
M
H
z
IC
801
R
X
n
R
X
p
T
X
p
T
X
n
P
on
P
S
E
L
V
DD
-P
A
D
R
V
4
3
6
7
T
X
on
R
X
on
D
801
6
72
AN
T1
AN
T2
9
8
AN
T1
ANT2
R
F
P
A
ANT1
AN
T2
78
73
74
80
L1
L
2
2
To AC Adaptor
Limit
Resistor
CHARGE
CONTACT
IC2
Q9
Q8
2.4V
Reg.
1.8V
Reg.
3.0 V
2.4 V
1.8 V
D
C
P
D
C
M
IC3
8
KX-TG2511CA/KX-TG2512CA/KX-TGA250RU
4.2.
Circuit Operation (Base Unit)
4.2.1.
Outline
Base Unit consists of the following ICs as shown in Block Diagram (Base Unit) (P.7).
• DECT BBIC (Base Band IC): IC7
- Handling all the audio, signal and data processing needed in a DECT base unit
- Controlling the DECT specific physical layer and radio section (Burst Module Controller section)
- ADPCM code filter for speech encoding and speech decoding (DSP section)
- Echo-cancellation and Echo-suppression (DSP section)
- Any tones (tone, sidetone, ringing tone, etc.) generation (DSP section)
- DTMF receiver (DSP section)
- Clock Generation for RF Module
- ADC, DAC, timer, and power control circuitry
- PLL Oscillator
- Detector
- Compress/Expander
- First Mixer
- All interfaces (ex: RF Power Amp, EEPROM, LED, Analog Front End, etc.)
- Controlling the DECT specific physical layer and radio section (Burst Module Controller section)
- ADPCM code filter for speech encoding and speech decoding (DSP section)
- Echo-cancellation and Echo-suppression (DSP section)
- Any tones (tone, sidetone, ringing tone, etc.) generation (DSP section)
- DTMF receiver (DSP section)
- Clock Generation for RF Module
- ADC, DAC, timer, and power control circuitry
- PLL Oscillator
- Detector
- Compress/Expander
- First Mixer
- All interfaces (ex: RF Power Amp, EEPROM, LED, Analog Front End, etc.)
• RF Power Amp.: IC801
- Amplifier for transmission and reception
• EEPROM: IC401
- Temporary operating parameters (for RF, etc.)
• Additionally,
- Power Supply Circuit (+3.0 V, +2.4 V, +1.8 V output)
- Crystal Circuit (10.368 MHz)
- Charge Circuit
- Telephone Line Interface Circuit
- Crystal Circuit (10.368 MHz)
- Charge Circuit
- Telephone Line Interface Circuit
Click on the first or last page to see other KX-TG2511CAM / KX-TG2511CAS / KX-TG2511CAT / KX-TG2512CAM / KX-TG2512CAT / KX-TGA250RUM / KX-TGA250RUS / KX-TGA250RUT service manuals if exist.