Panasonic KX-TG1411CAM / KX-TG1411CAT / KX-TG1412CA1 / KX-TGA141RUM / KX-TGA141RUT Service Manual ▷ View online
10
KX-TG1411CAM/KX-TG1411CAT/KX-TG1412CA1/KX-TGA141RUM/KX-TGA141RUT
4.3.
Block Diagram (Handset)
E a r p i e s e
( S p e a k e r )
A n a l o g
F r o n t
E n d
D S P
R F
C P U
X T A L
2 0 . 7 3 6 M H z
X101
E E P R O M
( I C 1 0 2 )
B A T T E R Y
C O S I C
C h a r g e +
C h a r g e -
R e g u l a t o r
3 . 3 V
B 1 3
B 1 4
B 3 8
B 6 9
B 6 8
B 5 9
B 5 8
C h a r g e
c i r c u i t
S C L K
D A T A
B 8 2
B 8 1
M I C
K E Y P A D
O N S W I T C H
R I N G E R
3 . 3 V
B 6 0
R
C H A R G E
C H A R G E
1 4 s e g
L C D
3 . 3 V
R O W S
C O L U M S
V D D B A T
V D D D C D C
Q 1 0
Q 1 0
B 6 1
B 2
B 9
2 . 4 V
2 . 4 V
Q101/102
2 . 4 V
C H A R G E
S T A R T
M A D 4 P
P 1 . 0
P 1 . 1
IC103
IC101
KX-TGA141 BLOCK DIAGRAM (HANDSET)
BZ2
11
KX-TG1411CAM/KX-TG1411CAT/KX-TG1412CA1/KX-TGA141RUM/KX-TGA141RUT
4.4.
Circuit Operation (Handset)
4.4.1.
Outline
Handset consists of the following ICs as shown in Block Diagram (Handset) (P.10).
• DECT BBIC (Base Band IC): IC103
- All data signals (forming/analyzing ACK or CMD signal)
- All interfaces (ex: Key, Detector Circuit, Charge, DC/DC Converter, EEPROM, LCD)
- PLL Oscillator
- Detector
- Compress/Expander
- Amplifier for transmission and reception
- All interfaces (ex: Key, Detector Circuit, Charge, DC/DC Converter, EEPROM, LCD)
- PLL Oscillator
- Detector
- Compress/Expander
- Amplifier for transmission and reception
• EEPROM: IC102
- Temporary operating parameters
4.4.2.
Power Supply Circuit/Reset Circuit
Circuit Operation:
When power on the Handset, the voltage is as follows;
The Reset signal generates R121, C186 and 2.6V.
4.4.3.
Charge Circuit
Circuit Operation:
When charging the handset on the Base Unit, the charge current is as follows;
DC+
DC+
→ F1 → D5 → R39 → CHARGE+ (Base) → CHARGE+ (Handset) → Q101 → L104 → BATTERY+... Battery...
BATTERY-
→ R102 → GND → CHARGE- (Handset)→ CHARGE- (Base) → GND → DC- (GND)
In this way, the BBIC on Handset detects the fact that the battery is charged.
The charge current is controlled by switching Q101 of Handset.
Refer to Fig.101 in Power Supply Circuit (P.8).
The charge current is controlled by switching Q101 of Handset.
Refer to Fig.101 in Power Supply Circuit (P.8).
4.4.4.
Battery Low/Power Down Detector
Circuit Operation:
“Battery Low” and “Power Down” are detected by BBIC which check the voltage from battery.
The detected voltage is as follows;
The detected voltage is as follows;
• Battery Low
Battery voltage: V (Batt) < 2.3V
The BBIC detects this level and “
The BBIC detects this level and “
” starts flashing and “battery alarm” starts ringing.
• Power Down
Battery voltage: V (Batt) < 2.2V
The BBIC detects this level and power down.
The BBIC detects this level and power down.
4.5.
Circuit Operation (Charger Unit)
4.5.1.
Power Supply Circuit
The power supply is as shown.
12
KX-TG1411CAM/KX-TG1411CAT/KX-TG1412CA1/KX-TGA141RUM/KX-TGA141RUT
4.6.
Signal Route
13
KX-TG1411CAM/KX-TG1411CAT/KX-TG1412CA1/KX-TGA141RUM/KX-TGA141RUT
5 Location of Controls and Components
Refer to the Operating Instructions.
Note:
You can download and refer to the Operating Instructions (Instruction book) on TSN Server.
6 Installation Instructions
Refer to the Operating Instructions.
Note:
You can download and refer to the Operating Instructions (Instruction book) on TSN Server.
7 Operating Instructions
Refer to the Operating Instructions.
Note:
You can download and refer to the Operating Instructions (Instruction book) on TSN Server.
7.1.
For Service Hint
Click on the first or last page to see other KX-TG1411CAM / KX-TG1411CAT / KX-TG1412CA1 / KX-TGA141RUM / KX-TGA141RUT service manuals if exist.