Panasonic KX-TCD951RUB Simplified Service Manual ▷ View online
•|
1
•|
KX-TCD951RUB
Simplified
Digital Cordless Phone
Telephone Equipment
KX-TCD951RUB
(for Russia)
WARNING
Please use this manual together with the original Service Manual for model KX-TCD951GB/KX-TCD955GC order
No.KM49910781C2. This Service Manual indicates the main differences between: Original KX-TCD951GB /KX-TCD955GC
and KX-TCD951RUB.
ORDER NO. KM40005622A1
Black Version
(Handset)
(Base Unit)
1
ABC
2
DEF
3
G HI
4
J KL
5
MNO
6
PQRS
7
TUV
8
0
WXYZ
9
INT'
OK
OK
C
PWR
RCL
PROG
RDL
•|
2
•|
KX-TCD951RUB
•¡
CONNECTION (Change from original page 6)
(Model KX-TCD951RUB)
Plug in the AC adaptor cord and the telephone line cord to the bottom of the unit. Then
connect the cord as shown.
USE ONLY WITH Panasonic AC ADAPTOR KX-TCA9CE OR KX-TCA11CE.
Be careful not to confuse the telephone line jack with the AC adaptor jack on the base unit. If
connected improperly, the base unit will not work and damage may occur.
The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during
use.)
The unit will not work during a power failure. We will recommend you connect a standard telephone
on the same line for power protection.
8V
9V
8V
9V
Fasten the cords to prevent them
from being disconnected.
from being disconnected.
Hooks
To Power Outlet
(AC 230 V, 50 Hz)
(AC 230 V, 50 Hz)
AC Adaptor
Telephone
Line Cord
Line Cord
AC
Adaptor
Adaptor
Telephone Line Cord
Single-Line
Telephone Jack
Telephone Jack
•|
3
•|
KX-TCD951RUB
•¡
LOCATION OF CONTROLS (Change from original page 3)
1
ABC
2
DEF
3
G HI
4
J KL
5
MNO
6
PQRS
7
TUV
8
0
WXYZ
9
R
INT’
OK
C
Tone Button
Display
Talk Button
Cancel Button
Program Button
Recall Button
Charge Contacts
Intercom Button
Redial/Pause
Button
Button
OK Button
Power Button
I N T
O K
R
Navigator Key
C
The underlined parts has been added to the original.
•¡
Battery Information (Change from original page 7)
•¡
•¡
•¡
•¡
•¡
TO REDIAL AFTER CONFIRMING THE NUMBERS IN REDIAL MEMORY (Changw from original page 11)
The underlined parts has been added to the original.
3
Press
.
• The number is dialed automatically.
• If your line has rotary or pluse service, any access numbers entered after pressing
will not be included when
redialing.
* Nickel metal hydride (Ni-MH) rechargeable batteries (AAA size) are available.
When you replace the batteries, you must program the battery type selection.
When you replace the batteries, you must program the battery type selection.
(Model KX-TCD951RUB)
•|
4
•|
KX-TCD951RUB
3. Send batch file “SET FREQ nn” to set the clock frequency. The default value of nn is 80. Increase the value to
increase the frequency. The clock frequency must be 10,368.000 kHz ± 0.04 kHz.
increase the frequency. The clock frequency must be 10,368.000 kHz ± 0.04 kHz.
•¡
CHECK PROCEDURE (Change from original page 41)
TEST EQUIPMENT REQUIRED AND EQUIPMENT SETUP
Connect a 3.9V supply to the board J5 (+), J8 (–).
INITIAL POWER + BBIC TESTS
4. Check the 3.0V supply voltage (TP10). It must be 2.85 +/– 0.3V.
5. Connect RFCLK (TP56) to CH.1 on the scope. Send batch file RFCLK1.
6. Check if the clock waveform is 10,368.000 kHz,+/– 40Hz.
7. Send batch file “SELF TEST”. The first 4digits are FLASH ROM checksum, the next 2 digits are RAM test,
and must be 00
5. Connect RFCLK (TP56) to CH.1 on the scope. Send batch file RFCLK1.
6. Check if the clock waveform is 10,368.000 kHz,+/– 40Hz.
7. Send batch file “SELF TEST”. The first 4digits are FLASH ROM checksum, the next 2 digits are RAM test,
and must be 00
SET CLOCK FREQUENCY
1. Send batch file “RFCLK1”.
(Model KX-TCD951RUB)
•¡
CABINET AND ELECTRICAL PARTS LOCATION (HANDSET) [Change from original page 54]
Addition
LCD
121
121