Panasonic KX-TCD951EB / KX-TCD955EC Service Manual ▷ View online
45
KX-TCD951EB/KX-TCD955EC
H A N D S E T: LINK.
2
Is the base unit
registration data contained
in the handset?
Six handsets have already been
registered in the base unit.
registered in the base unit.
Does the LCD
Display remain on,
and is the handset number
displayed?
Does the LCD
Display remain on,
and is the handset number
displayed?
Does the LCD
Display remain on,
and is the handset number
displayed?
The handset has a hardware
(EEPROM, etc.) defect.
(EEPROM, etc.) defect.
The handset has a hardware
(RF unit, etc.) defect.
(RF unit, etc.) defect.
Set the base unit selection to "0".
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
(Use the method for clearing the registered handset data in the base unit.)
Use the serial communication tool to
initialize the data inside the base unit.
initialize the data inside the base unit.
Did the error
beep sound?
beep sound?
Was the registration
successful?
Use the service password (0000) to
register the handset in the base unit.
register the handset in the base unit.
Was the registration
successful?
Use the base password to register the
handset in the base unit.
handset in the base unit.
3
C
A
Set the handset's power switch OFF
and then back to ON.
and then back to ON.
The handset has a hardware
(EEPROM, etc.) defect.
(EEPROM, etc.) defect.
B
Set the handset's power switch OFF
and then back to ON.
and then back to ON.
No
46
KX-TCD951EB/KX-TCD955EC
The base unit has a hardware
(EEPROM, etc.) defect.
(EEPROM, etc.) defect.
Yes
No
A mistake was made in the base unit
selection operation.
selection operation.
A
Disconnect and re-connect the base
unit's AC adaptor.
unit's AC adaptor.
The handset has a hardware
(EEPROM, etc.) defect.
(EEPROM, etc.) defect.
Yes
No
Disconnect and re-connect the base
unit's AC adaptor.
unit's AC adaptor.
B
Set the handset's power switch OFF
and then back to ON.
and then back to ON.
The base unit has a hardware
(EEPROM, etc.) defect.
(EEPROM, etc.) defect.
Yes
No
The registration data has been cleared
due to a mistake made in the operation.
due to a mistake made in the operation.
Does the LCD
Display remain on,
and is the handset number
displayed?
Does the LCD
Display remain on,
and is the handset number
displayed?
Does the LCD
Display remain on,
and is the handset number
displayed?
47
KX-TCD951EB/KX-TCD955EC
H A N D S E T: DOES NOT LINK.
The base unit has a hardware
(EEPROM, etc.) defect.
(EEPROM, etc.) defect.
Yes
C
No
The password is wrong.
Set a new password.
Set a new password.
Disconnect and re-connect the base
unit's AC adaptor.
unit's AC adaptor.
Does the LCD
Display remain on,
and is the handset number
displayed?
Check the RFM1, IC1 and X1
soldering.
soldering.
Conduct an evaluation test on the
RF unit of the handset
(follow check procedure B). OK?
RF unit of the handset
(follow check procedure B). OK?
Does the signal output from IC1 pin 10 (TP56)
of the handset have a frequency of
10.368 MHz ± 40 Hz when the AC adaptor
for the base unit has been disconnected?
of the handset have a frequency of
10.368 MHz ± 40 Hz when the AC adaptor
for the base unit has been disconnected?
3
Yes
OK
NG
Yes
Fails to link (base unit)?
Clear the handset registration
data in the base unit.
data in the base unit.
(Refer to page 40.)
Adjust the clock frequency
to 10.368 MHz ± 40 Hz.
to 10.368 MHz ± 40 Hz.
48
KX-TCD951EB/KX-TCD955EC
BASE UNIT: DOES NOT CHARGE.
200 mA
ammeter
ammeter
J6
J7
3 size "AA"
NiCd batteries
connected in series
NiCd batteries
connected in series
Connect the AC adaptor.
Is a voltage of 8V or more
supplied between J2 pins
6 and 5?
supplied between J2 pins
6 and 5?
Is a charging current of approx.
80 mA flowing while the tool
shown in Fig. 35 is connected?
80 mA flowing while the tool
shown in Fig. 35 is connected?
Check T16, R64, D11, R65, R66
and D12.
and D12.
Check for defects in the batteries.
Check the extent to which the
handset is charged.
Check the extent to which the
handset is charged.
Does the charge LED light
(while the tool shown in Fig. 35
is connected)?
(while the tool shown in Fig. 35
is connected)?
Check R61, T14,
D13 and R58
D13 and R58
Check R63, J4, J3 and D13
Is the voltage on the T15
Base < 1 V?
Base < 1 V?
Check the AC adaptor.
No
No
Yes
No
Yes
Fig. 31
Yes
No
Yes
A
Click on the first or last page to see other KX-TCD951EB / KX-TCD955EC service manuals if exist.