DOWNLOAD Panasonic KX-TCD325UA / KX-TCA132UA / KX-TCA130UA Service Manual ↓ Size: 2.14 MB | Pages: 115 in PDF or view online for FREE

0x0185

1

EEP_FactoryLanguageSetting Selected Language for LCD

GERAM:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3
FRENCH:4
ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8 FINNISH:9
GREEK:10 TURKISH:11 HUNGARIAN:12
PORTUGUESE:13
RUSSIAN:14
POLISH:15 SLOVAKIAN:16 CZECH:17 CROATIAN:18
CATALAN:19

0x01

0x20

0x0186

1

EEP_Available_Language

Select Available Language
0:Disable, 1:Enable
Bit0:German
Bit1:English
Bit2:Spanish
Bit3:Norwegian
Bit4:French
Bit5:Italian
Bit6:Danish
Bit7:Dutch

0xFF

0x02

0x0187

Select Available Language
0:Disable, 1:Enable
Bit0:Swedish
Bit1:Finnish
Bit2:Greek
Bit3:Turkish
Bit4:Hungarian
Bit5:Portuguese
Bit6:Russian
Bit7:Polish

0x2F

0x40

0x0188

Select Available Language
0:Disable, 1:Enable
Bit0:Slovakian
Bit1:Czechs
Bit2:Croatian
Bit3:Catalan
Bit4:Ukrinian
Bit5:Spanish for Mexico
Bit6:Slovenian
Bit7:Estonian

0x08

0x10

0x0189

Select Available Language
0:Disable, 1:Enable
Bit0:Lithuanian
Bit1:Latvian
Bit2:Romanian
Bit3:Bulgarian
Bit4:Seribian
Bit5:Macedonian
Bit6:Albanian
Bit7:Reserve

0x00

0x00

0x034C

3

EEP_Language

User_Setting Language
GERAM:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3
FRENCH:4
ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8 FINNISH:9
GREEK:10 TURKISH:11 HUNGARIAN:12 PORTUGUESE:13
RUSSIAN:14
POLISH:15 SLOVAKIAN:16 CZECH:17 CROATIAN:18
CATALAN:19

0x01

X

0x034D

3

EEP_SmsEatoniLanguage

Eatoni Setting Language
GERAM:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3
FRENCH:4
ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8 FINNISH:9
GREEK:10 TURKISH:11 HUNGARIAN:12 PORTUGUESE:13
RUSSIAN:14
POLISH:15 SLOVAKIAN:16 CZECH:17 CROATIAN:18
CATALAN:19

0x01

X

0x02A7

1

EEP_CountryFunction

Country parameter
0bit: Reset Ear-SP Vol. after Talk...0: Hold, 1: Reset
1bit: PBX Phone-Book...0: Enable, 1: Disable
2bit: Ringer Option Menu (Base Setting)...0: Off, 1: On
3-7bit: Reserve

0x02

x

89

0x0102

1

EEP_DspSdtLevel

DSP Parameter SideTone2
Main:SideTone2 Main route level
MictoRcv:SideTone2 MIc to Receiver level

0x00,0x0E

x

0x0104

1

EEP_DspToneLevel

DSP Parameter ToneLevel
Talk:Tone Level in Talk mode
Spp:Tone Level in Spp mode

0x00,0x20,0x00,0x30

x

0x0108

1

EEP_DspRcvVol

DSP Parameter Receiver Volume TX Level
TxTalk:Receiver Volume Tx Level in Talk mode
TxSpp:Receiver Volume Tx Level in Spp mode

0xFF,0x7F

x

0x000E

F

EEP_LcdContrast

0x20

x

0x0155

1

EEP_CountryFunction01

Country parameter
Bit0:Call waiting Tone on/off...1:on, 0:off
Bit1:Clock Back Up...1:on, 0:off
Bit2:Charge ON Tone...1:Tone on, 0:KeyTone operating
Bit3:BackUpTime revise...1:on, 0:off
Bit4:On Charge Partial...1:none, 0:Partial Display
Bit5:Start Talk Count Delay on/off...1:on, 0:off
Bit6-7:Reserve

0x3E

x

0x0158

3

EEP_EEToneConfig

Tone Option Data
Bit0:Keytone on/off00 - 0000 = Off / 0001 = Tone On
Bit1:Keytone on/off01 - Reserve
Bit2:Keytone on/off02 - Reserve
Bit3:Keytone on/off03 - Reserve
Bit4:Call waiting on/off - 1/0
Bit5:Range alarm on/off - 1/0
Bit6:Battery low alarm on/off - 1/0

0x51

x

0x0004

F

EEP_LowVoltage

0x25

x

0x0005

F

EEP_NoVoltage

0x08

x

90

Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount),
a soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.

     ·    PbF (: Pb free) Solder
     ·    Soldering Iron

Tip Temperature of 700°F ± 20°F (370°C ± 10°C)
Note: We recommend a 30 to 40 Watt soldering iron. An expert may be able to use a 60 to 80 Watt iron where someone with
less experience could overheat and damage the PCB foil.

     ·    Flux

Recommended Flux: Specific Gravity

→ 0.82.

Type

→ RMA (lower residue, non-cleaning type)

Note: See ABOUT LEAD FREE SOLDER (PbF: Pb free) (P.4).

 1. Put plenty of solder on the IC pins so that the pins can be completely covered.

If the IC pins are not soldered enough, you may give pressure to the P.C. board when cutting the pins with a cutter.

 2. Make a few cuts into the joint (between the IC and its pins) first and then cut off the pins thoroughly.

 3. While the solder melts, remove it together with the IC pins.

When you attach a new IC to the board, remove all solder left on the land with some tools like a soldering wire. If some solder is
left at the joint on the board, the new IC will not be attached properly.

91

 1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins.

*Check the accuracy of the IC setting with the corresponding soldering
foil.

 2. Apply flux to all pins of the FLAT PACKAGE IC.

 3. Solder the pins, sliding the soldering iron in the direction of the arrow.

 1. Lightly resolder the bridged portion.
 2. Remove the remaining solder along the pins using a soldering iron as shown in the figure below.

92