Panasonic KX-TC1045RUB Service Manual ▷ View online
10.3. CH CHANGE MODE:
21
KX-TC1045RUB
10.4. To terminate Communication
10.5. Ringing
After detecting the Ring signal from circuit, Base Unit sends a ring signal DATA (Ring) on the base´s (a) TX frequency, then the
Handset starts ringing.
Note: (a) is channels 1-10 (old)...cthese channels are paired as per law requirements.
Handset starts ringing.
Note: (a) is channels 1-10 (old)...cthese channels are paired as per law requirements.
22
KX-TC1045RUB
10.6. Waveform of DATA Used for Cordless Transmission and Reception
The DATA which is transmitted from the Handset to the Base Unit is combination of DATA 0, DATA 1, DATA Delimt, Pre data
and End data.
The DATA which is transmitted from the Base Unit to the Handset is combination of DATA 0, DATA 1, DATA Delimt, Pre data
and End data.
and End data.
The DATA which is transmitted from the Base Unit to the Handset is combination of DATA 0, DATA 1, DATA Delimt, Pre data
and End data.
10.6.1. Handset
10.6.2. Base Unit
Transmitting DATA Format
23
KX-TC1045RUB
10.7. When LINKing
When LINKing from the Handset (when becoming STBY to
TALK), DATA is transmitted in above format. The combined
portion of DATA 0 and DATA 1 is transmitted in LINK
requesting DATA (40bit) format first. Then, when LINK OK
(ACK-OK) DATA (46bit) is returned from the Base Unit, it is
sent as LINK from DATA after changing the combination of
DATA 0 and DATA 1. And the DATA Delimit is between each
Frame as a stop.
The contents of LINK requesting DATA and LINK form DATA
are different depending on each operation.
TALK), DATA is transmitted in above format. The combined
portion of DATA 0 and DATA 1 is transmitted in LINK
requesting DATA (40bit) format first. Then, when LINK OK
(ACK-OK) DATA (46bit) is returned from the Base Unit, it is
sent as LINK from DATA after changing the combination of
DATA 0 and DATA 1. And the DATA Delimit is between each
Frame as a stop.
The contents of LINK requesting DATA and LINK form DATA
are different depending on each operation.
10.8. Pulse Dial
When executing Pulse Dial, the Pulse Dial DATA is transmitted
from the Handset to the Base Unit in above format. The
combination of DATA 0 and DATA 1 are changed by each Dial
No. And the DATA Delimt is between each Frame as a stop.
The number of Frame is 2.
from the Handset to the Base Unit in above format. The
combination of DATA 0 and DATA 1 are changed by each Dial
No. And the DATA Delimt is between each Frame as a stop.
The number of Frame is 2.
10.9. Tone Dial
When executing Tone Dial, Tone Dial DATA is transmitted from
the Handset to the Base Unit in above format. The DATA is
changed by Dial No. as same as Pulse Dial. When Tone
Dialing, DATA (Continue DATA) that the key is pressed
continuously is sent to the Base Unit during the key is pressed.
When depressing the key, the END data is sent finally.
Note:
the Handset to the Base Unit in above format. The DATA is
changed by Dial No. as same as Pulse Dial. When Tone
Dialing, DATA (Continue DATA) that the key is pressed
continuously is sent to the Base Unit during the key is pressed.
When depressing the key, the END data is sent finally.
Note:
1,000,000 kinds of the security code are available for the
mode KX-TC1045RUB. Each time the Handset is set on the
cradle of the base unit (for charging), the CPU automatically
change the security code.
mode KX-TC1045RUB. Each time the Handset is set on the
cradle of the base unit (for charging), the CPU automatically
change the security code.
11 FREQUENCY TABLE
(MHz)
24
KX-TC1045RUB
Click on the first or last page to see other KX-TC1045RUB service manuals if exist.