Panasonic KX-PRW110RUW / KX-PRW120RUW / KX-PRWA10RUW Service Manual ▷ View online
49
KX-PRW110RUW/KX-PRW120RUW/KX-PRWA10RUW
11.2.2. How to install Batch file into P.C.
Note:
• “*****” varies depending on the country or models.
11.2.3. Commands
See the table below for frequently used commands.
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
98” is written.
hookoff
Off-hook mode on Base
Type “hookoff”.
hookon
On-hook mode on Base
Type “hookon”.
getchk
Read checksum
Type “getchk”.
wreeprom
Write the data of EEPROM
Type “wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
is data to be written.
1.
Insert the Batch file CD-ROM into CD-ROM drive and
copy PNZZTG**** folder to your PC (example: D drive).
2.
Open an MS-DOS mode window.
3.
At the DOS prompt, type "D:" (for example) to select the
drive, then press the Enter key.
4.
Type "CD
㪳PNZZTG****", then press the Enter key.
5.
Type "SET_COM=X", then press the Enter key
(X: COM port number used for the serial connection on your PC).
6.
Type "READID", then press the Enter key.
䊶If any error messages appear, change the port number or
䇭check the cable connection.
䊶If any value appear, go to next step.
7.
Type "DOSKEY", then press the Enter key.
<Example>
C:
>Documents and Settings>D:
D:
>>CD >PNZZTG****
D:
>PNZZTG**** >SET_COM=X
D:
>PNZZTG****>READID
00 52 4F A8 A8
D:
D:
>PNZZTG****>DOSKEY
D:
>PNZZTG****>
<Example: error happens>
C:
>Documents and Settings>D:
D:
>>CD >PNZZTG****
D:
>PNZZTG**** >SET_COM=X
D:
>PNZZTG****>READID
ޓCreateFile error
ERROR 10: Can't open serial port
D:
ERROR 10: Can't open serial port
D:
>PNZZTG ****>
<Example for Windows>
On your computer, click [Start], select Programs
(All Programs for Windows XP/Windows Server 2003),
then click
MS-DOS Prompt. (for Windows 95/Windows 98)
Or
Accessories-MS-DOS Prompt. (for Windows Me)
Or
Command Prompt. (for Windows NT 4.0)
Or
Accessories-Command Prompt.
(for Windows 2000/Windows XP/Windows Server 2003)
(All Programs for Windows XP/Windows Server 2003),
then click
MS-DOS Prompt. (for Windows 95/Windows 98)
Or
Accessories-MS-DOS Prompt. (for Windows Me)
Or
Command Prompt. (for Windows NT 4.0)
Or
Accessories-Command Prompt.
(for Windows 2000/Windows XP/Windows Server 2003)
50
KX-PRW110RUW/KX-PRW120RUW/KX-PRWA10RUW
11.3. Adjustment Standard (Base Unit)
When connecting the simulator equipment for checking, please refer to below.
11.3.1. Bottom View
Note:
(A) - (Q) is referred to Check Point (Base Unit) (P.37)
WIFIRX
DCM
DCP
ANT2-Short
C601
C602
WIFITX
CHARGE+
CHARGE-
F301
ANT1
ANT2
URX
LINE_DC
STM/CKM/P27
C867
C868
C869
UTX
IC601
Q142
Q144
Q352
Q354
Q161
R101
C895
R102
R103
R104
GPIO0
R105
R106
R109
W_GND
R110
R111
R112
R115
R116
R117
R118
R508
R511
R512
R513
R514
R515
R321
R322
C103
C104
C105
R142
C106
R143
C107
R144
C108
R145
C109
VDD1
R146
VDD2
R147
VDD3
R148
C301
C110
C111
C112
C113
C115
R151
C116
R152
C501
C502
L1R
C507
C508
L1T
C123
R353
R160
C124
R161
C125
R162
R163
R164
R358
R165
R359
R166
C513
R167
R168
C321
R169
C322
C518
R360
C519
R170
+5.5V
R178
R371
C141
R372
C143
ANT2-S-GND
C531
C532
C533
C534
C535
C152
C351
C352
C161
C163
C164
C165
C166
C167
C168
C171
C172
C173
W_VCC
C174
W_URX
1.5V
C181
C184
C186
IC302
W_UTX
IC502
GND
D362
C353
JTAG
RST
GRY
PUR
+
–
YLW
BRN
TP9
TP10
A
PbF
PNLB2199Z
12
2W
Digital
(P)
Volt Meter
CHG-
CHG+
(G)
GND
CKM
Frequency
Counter
TX
GND
RX
PC
Jig
50
T
e
rminal
VDD1 (B)
VDD3 (A)
VDD2 (R)
ANT 2
Short
Short
1.5V (C)
51
KX-PRW110RUW/KX-PRW120RUW/KX-PRWA10RUW
11.4. The Setting Method of JIG (Handset)
This section explains the PC setting to use command required in Check Point (Handset)(P.39).
<Preparation>
• Serial JIG cable: PQZZ1CD300E*
• PC which runs in DOS mode
• Batch file CD-ROM for setting: PNZZPRW120RU
• PC which runs in DOS mode
• Batch file CD-ROM for setting: PNZZPRW120RU
Note:
*: If you have the JIG Cable for TCD500 series
(PQZZ1CD505E), change the following values of
resistance. Then you can use it as a JIG Cable for both
TCD300 and TCD500 series. (It is an upper compatible JIG
Cable.)
(PQZZ1CD505E), change the following values of
resistance. Then you can use it as a JIG Cable for both
TCD300 and TCD500 series. (It is an upper compatible JIG
Cable.)
11.4.1. Connections
Connect the DC Power or Battery to BATT+ and BATT-.
Connect the JIG cable GND (black) to GND.
Connect the JIG cable UTX (yellow) to UTX and URX (red) to URX.
Connect the JIG cable GND (black) to GND.
Connect the JIG cable UTX (yellow) to UTX and URX (red) to URX.
Note:
*: COM port names may vary depending on what your PC calls it.
Resistor
Old value (k
Ω) New value (kΩ)
R2
22
3.3
R3
22
3.3
R4
22
4.7
R7
4.7
10
DC Power
or Battery
2
GND (black)
3
To Serial Port
(com port 1*)
(com port 1*)
JIG Cable
PC
URX (red)
3
UTX (yellow)
Handset P. C. board
1
BATT-
BATT+
GND
UTX
URX
52
KX-PRW110RUW/KX-PRW120RUW/KX-PRWA10RUW
11.4.2. How to install Batch file into P.C.
Note:
• “*****” varies depending on the country or models.
11.4.3. Commands
See the table below for frequently used commands.
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
98” is written.
getchk
Read checksum
Type “getchk”.
wreeprom
Write the data of EEPROM
Type “wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
is data to be written.
1.
Insert the Batch file CD-ROM into CD-ROM drive and
copy PNZZTG***** folder to your PC (example: D drive).
2.
Open an MS-DOS mode window.
3.
At the DOS prompt, type "D:" (for example) to select the
drive, then press the Enter key.
4.
Type "CD
㪳PNZZTG*****", then press the Enter key.
5.
Type "SET RTX_COM=X", then press the Enter key
(X: COM port number used for the serial connection on your PC).
6.
Type "READID", then press the Enter key.
䊶If any error messages appear, change the port number or
䇭check the cable connection.
䊶If any value appear, go to next step.
7.
Type "DOSKEY", then press the Enter key.
<Example>
C:
>Documents and Settings>D:
D:
>>CD >PNZZTG*****
D:
>PNZZTG***** >SET RTX_COM=X
D:
>PNZZTG*****>READID
00 52 4F A8 A8
D:
D:
>PNZZTG*****>DOSKEY
D:
>PNZZTG*****>
<Example: Error happens>
C:
>Documents and Settings>D:
D:
>>CD >PNZZTG*****
D:
>PNZZTG***** >SET RTX_COM=X
D:
>PNZZTG*****>READID
ޓCreateFile error
ERROR 10: Can't open serial port
D:
ERROR 10: Can't open serial port
D:
>PNZZTG*****>
<Example for Windows>
On your computer, click [Start], select Programs
(All Programs for Windows XP/Windows Server 2003),
then click
MS-DOS Prompt. (for Windows 95/Windows 98)
Or
Accessories-MS-DOS Prompt. (for Windows Me)
Or
Command Prompt. (for Windows NT 4.0)
Or
Accessories-Command Prompt.
(for Windows 2000/Windows XP/Windows Server 2003)
(All Programs for Windows XP/Windows Server 2003),
then click
MS-DOS Prompt. (for Windows 95/Windows 98)
Or
Accessories-MS-DOS Prompt. (for Windows Me)
Or
Command Prompt. (for Windows NT 4.0)
Or
Accessories-Command Prompt.
(for Windows 2000/Windows XP/Windows Server 2003)
Click on the first or last page to see other KX-PRW110RUW / KX-PRW120RUW / KX-PRWA10RUW service manuals if exist.