Panasonic KX-TG2511RUM / KX-TG2511RUN / KX-TG2511RUS / KX-TG2511RUT / KX-TG2512RUN / KX-TG2512RUS / KX-TG2521RUT / KX-TGA250RUM / KX-TGA250RUN / KX-TGA250RUS / KX-TGA250RUT Service Manual / Supplement ▷ View online
21
KX-TG2511RUM/KX-TG2511RUN//KX-TG2511RUS/KX-TG2511RUT/KX-TG2512RUN/KX-TG2512RUS/KX-TG2521RUT/KX-TGA250RUM/KX-TGA250RUN/KX-TGA250RUS/KX-TGA250RUT
Frequently Used Items (Base Unit)
ex.)
Note:
(*1) Refer to Registering a Handset to a Base Unit in the Operating Instructions.
(*2) When you enter the address or New Data, please refer to the table below.
(*2) When you enter the address or New Data, please refer to the table below.
(*3)
Items
Address
Default Data
New Data
Remarks
C-ID (FSK) sensitivity
06 64/06 63
00/28
00/1C
(3 dB up)
00/14
(6 dB up)
When hex changes from “00/28” to “00/1C” or
“00/14”, gain increases by 3 dB or 6 dB.
“00/14”, gain increases by 3 dB or 6 dB.
C-ID (DTMF) sensitivity
06 80/06 7F
08/00
0B/4C
(3 dB up)
0F/F6
(6 dB up)
When hex changes from “08/00” to “0B/4C” or
“0F/F6”, gain increases by 3 dB or 6 dB.
“0F/F6”, gain increases by 3 dB or 6 dB.
Frequency
00 08/00 07
01/00
-
-
Use these items in a READ-ONLY mode to
confirm the contents. Careless rewriting may
cause serious damage to the computer system.
confirm the contents. Careless rewriting may
cause serious damage to the computer system.
ID
00 02~00 06
Given value
-
-
Bell length
02 9A
32 (5 sec) (*3)
1E (3 sec)
14 (2 sec)
This is time until bell stops ringing.
(Unit: 100 msec)
(Unit: 100 msec)
Desired Number (hex)
Input Keys
Desired Number (hex)
Input Keys
0
0
A
[R] + 0
1
1
B
[R] + 1
.
.
C
[R] + 2
.
.
D
[R] + 3
.
.
E
[R] + 4
9
9
F
[R] + 5
Bell length
32 (hex) = 50 (dec)
50 100 msec = 5000 msec (5 sec)
22
KX-TG2511RUM/KX-TG2511RUN//KX-TG2511RUS/KX-TG2511RUT/KX-TG2512RUN/KX-TG2512RUS/KX-TG2521RUT/KX-TGA250RUM/KX-TGA250RUN/KX-TGA250RUS/KX-TGA250RUT
9.1.2.
Handset
[Changed from original section “8.1.2. Handset”]
Important:
Make sure the address on LCD is correct when entering new data. Otherwise, you may ruin the unit.
H/S key operation
H/S LCD
1). Press .
2). Select "Handset Setup" using or
then press or
then press or
{>}
.
{^} {V}
3). Enter "7", "2", "6", "2", "7", "6", "6", "4".
Note: 7262 7664 = PANA SONI
(see letters printed on dial keys)
5). Enter "
٨
", "
٨
", "
٨
", "
٨
" (Address). (*1)
7). Press , a long confirmation beep
will be heard.
8). Press (off) to return to standby mode.
After that, remove and reinsert the batteries. Press the Power button for
about 1 second if the power is not turned on.
about 1 second if the power is not turned on.
6). Enter "
㧖", "㧖" (New Data). (*1)
4). Select "Write EEP" using or
then press or
then press or
{>}
.
{^} {V}
{j/OK} (Menu/OK)
{ic} (Off/Power)
{ECO/R}
ECO: Eco mode shortcut ke
ECO: Eco mode shortcut ke
Dial keypad
y
R: Recall/Flash
Navigator key/
?
(Volume) key
j
Default Data
New Data
Caller List
V^
Handset Setup
V^
Set Addr.:
_ _ _ _ _ _
Set Addr.:
Set Addr.:
Set Date & Time
V^
Service Mode
Read EEP
Write EEP
Read EEP
Write EEP
^
M
M
M
{ic}
23
KX-TG2511RUM/KX-TG2511RUN//KX-TG2511RUS/KX-TG2511RUT/KX-TG2512RUN/KX-TG2512RUS/KX-TG2521RUT/KX-TGA250RUM/KX-TGA250RUN/KX-TGA250RUS/KX-TGA250RUT
Frequently Used Items (Handset)
ex.)
Note:
(*1) When you enter the address or New Data, please refer to the table below.
(*2) When adding “01” (hex) to default value, sending level increases by 0.25 dB.
ex.)
ex.)
(*3) When reducing “01” (hex) from default value, receiving level increases by 0.25 dB.
ex.)
ex.)
(*4) Use these items in a READ-ONLY mode to confirm the contents. Careless rewriting may cause serious damage to the
handset.
handset.
Items
Address
Default Data
New Data
Possible Adjusted
Value MAX (hex)
Possible Adjusted
Value MIN (hex)
Remarks
Sending level
05 3F
Adjusted value
Given value
FF
D0
(*2)
Receiving level
05 40
Adjusted value
Given value
FF
D0
(*3)
Battery Low
00 09
70
-
-
-
(*4)
Frequency
00 08/00 07
02/70
-
-
-
ID
00 02~00 06
Given value
-
-
-
Desired Number (hex.)
Input Keys
Desired Number (hex.)
Input Keys
0
0
A
[R] + 0
1
1
B
[R] + 1
.
.
C
[R] + 2
.
.
D
[R] + 3
.
.
E
[R] + 4
9
9
F
[R] + 5
Item
Default Data
New Data
E7
EB
E3
Sending level
-8 dBm
-7 dBm
-9 dBm
Item
Default Data
New Data
E7
EB
E3
Receiving level
-22 dBm
-23 dBm
-21 dBm
24
KX-TG2511RUM/KX-TG2511RUN//KX-TG2511RUS/KX-TG2511RUT/KX-TG2512RUN/KX-TG2512RUS/KX-TG2521RUT/KX-TGA250RUM/KX-TGA250RUN/KX-TGA250RUS/KX-TGA250RUT
9.2.
EEPROM LAYOUT (Handset)
9.2.1.
Scope
The purpose of this section is to describe the layout of the EEPROM (IC3) for the KX-TGA277 Handset.
The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the
The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the
handset, some are set by the user when configuring the handset, and some during normal use of the phone.
9.2.2.
Introduction
The handset uses a 64k bit serial EEPROM (IC3) for storing volatile parameters. All parameters are set up before the handset
the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed before the
actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
This document lists all default parameters with a short description.
the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed before the
actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
This document lists all default parameters with a short description.
9.2.3.
EEPROM contents
MMI Setting:
MMI1 Setting:
Initial Type
Description
F
The data initialized by only F command
0
The data initialized by F and 0 command
1
The data initialized by F, 0 and 1 command
2
The data initialized by F, 0, 1 and 2 command
3
The data initialized by all command (F, 0, 1, 2, 3)
Country Setting
Description
x
Default - no specific country setting, so revert to default value.
Address Initial
Type
Name
Description
Default value
Country
Setting
049F
3
EEP_Language
Selected Language for LCD
GERMAN:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3
FRENCH:4
ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8 FINN-
ISH:9
GREEK:10 TURKISH:11 HUNGARIAN:12 PORTU-
GUESE:13 RUSSIAN:14
POLISH:15 SLOVAKIAN:16 CZECH:17 CROATIAN:18
CATALAN:19
UKRINIAN:20 SPANISHMEX:21 SLOVENIAN:22 EST-
NIAN:23 LITHUANIAN:24
LATVIAN:25 ROMANIAN:26 BULGARIAN:27 SER-
BIAN:28 MACEDONIAN:29
ALBANIAN:30 PORTUGUESEMEX:31 Reserve:32
HEBREW:33
ARABIC:34 PERSIA:35 HANTAI:36 HANTAI(HK):37
RUSSIAN(BX):38
BELARUS:39 KAZAKHSTAN:40 UZBEKISTAN:41
TAJIKISTAN:42 TURKMENISTAN:43
AZERBAIJAN:44 ARMENIA:45 MOLDOV:46 Reserve:47
CANADAENGLISH:48 USSPANISH:49 USFRENCH:50
GERMAN:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3
FRENCH:4
ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8 FINN-
ISH:9
GREEK:10 TURKISH:11 HUNGARIAN:12 PORTU-
GUESE:13 RUSSIAN:14
POLISH:15 SLOVAKIAN:16 CZECH:17 CROATIAN:18
CATALAN:19
UKRINIAN:20 SPANISHMEX:21 SLOVENIAN:22 EST-
NIAN:23 LITHUANIAN:24
LATVIAN:25 ROMANIAN:26 BULGARIAN:27 SER-
BIAN:28 MACEDONIAN:29
ALBANIAN:30 PORTUGUESEMEX:31 Reserve:32
HEBREW:33
ARABIC:34 PERSIA:35 HANTAI:36 HANTAI(HK):37
RUSSIAN(BX):38
BELARUS:39 KAZAKHSTAN:40 UZBEKISTAN:41
TAJIKISTAN:42 TURKMENISTAN:43
AZERBAIJAN:44 ARMENIA:45 MOLDOV:46 Reserve:47
CANADAENGLISH:48 USSPANISH:49 USFRENCH:50
0x0E
x
Address Initial
Type
Name
Description
Default value
Country
Setting
0011
F
EEP_LcdContrast
LCD contrast
0x32
x
Click on the first or last page to see other KX-TG2511RUM / KX-TG2511RUN / KX-TG2511RUS / KX-TG2511RUT / KX-TG2512RUN / KX-TG2512RUS / KX-TG2521RUT / KX-TGA250RUM / KX-TGA250RUN / KX-TGA250RUS / KX-TGA250RUT service manuals if exist.