Panasonic PT-VW345NZ / PT-VW345NZD / PT-VX415NZ / PT-VX415NZD Service Manual ▷ View online
6
PREFACE
Model No.
PT-VW345NZ
PT-VX415NZ
Termi-
nals
<COMPUTER 1
IN>
1 (High-density D-sub 15 pin female)
[RGB signal]
0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 V [p-p] 75 Ω)
HD/SYNC TTL high impedance, automatic positive/negative polarity compatible
VD TTL high impedance, automatic positive/negative polarity compatible
[YP
B
P
R
signal] Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
<COMPUTER 2
IN/1 OUT>
1 (High-density D-sub 15 pin female)
[RGB signal]
0.7 V [p-p] 75 Ω (When G-SYNC: 1.0 V [p-p] 75 Ω)
HD/SYNC TTL high impedance, automatic positive/negative polarity compatible
VD TTL high impedance, automatic positive/negative polarity compatible
<VIDEO IN>
1 (Pin jack 1.0 V [p-p] 75 Ω)
<S-VIDEO IN>
1 (Mini DIN 4 pin, Y 1.0 V [p-p], C 0.286 V [p-p] 75 Ω, S1 signal compatible)
<HDMI IN>
1 (HDMI 19 pin, HDCP and Deep color compatible)
Audio signals: Linear PCM (Sampling frequency: 48 kHz/44.1 kHz/32 kHz)
<AUDIO IN>
2 (M3 stereo mini jack, 0.5 V [rms], input impedance 22 kΩ and more)
(<AUDIO IN 2 (MIC IN)> terminal support MIC input)
1 (Pin jack x 2 (L-R), 0.5 V [rms], input impedance 22 kΩ and more)
<VARIABLE AU-
DIO OUT>
1 (M3 stereo mini jack, stereo monitor output compatible,
0 V [rms] to 2.0 V [rms] variable, output impedance 2.2 kΩ and less)
<USB A/VIEWER> USB connector (type A x 1)
<USB B/DISPLAY> USB connector (type B x 1)
<SERIAL IN>
<USB B/DISPLAY> USB connector (type B x 1)
<SERIAL IN>
1 (D-sub 9 pin, RS-232C compliant, for computer control use)
<LAN>
1 (for RJ-45 network connection, PJLink compatible,)
Wireless
LAN
Specification
standards
IEEE 802.11a/n : 5.180 GHz - 5.850 GHz
IEEE 802.11b/g/n : 2.412 GHz - 2.472 GHz
Power cable length
For Europe, U.K. and USA: 2.0 m (78 3/4")
For India: 3.0 m (118 1/8")
Cabinet
Molded plastic
Dimensions
Width: 352 mm (13.86")
Height: 98 mm (3.86") (when adjustable feet shortened)
Depth: 279.4 mm (11")
Weight
Approx.3.4 kg (7.5 lbs.) *
4
Noise level *
5
When set to [NORMAL] in [LAMP POWER] : 35 dB
When set to [ECO1] or [ECO2] in [LAMP POWER] : 29 dB
Operating environment
Operating environment temperature *
6
:
0 °C (32 °F) to 40 °C (104 °F)
(Elevation: below 1 400 m; [HIGH ALTITUDE MODE]: [OFF])
0 °C (32 °F) to 30 °C (86 °F)
(Elevation: 1 400 m ~ 2 000 m; [HIGH ALTITUDE MODE]: [HIGH1])
0 °C (32 °F) to 30 °C (86 °F)
(Elevation: 2 000 m ~ 2 700 m; [HIGH ALTITUDE MODE]: [HIGH2])
Operating environment humidity: 10 % to 80 % (no condensation)
Remote
control
Power supply
DC 3 V (battery (AAA/R03 or AAA/LR03 Type ) x 2)
Operating range Approx. 7 m (275.6") (when operated directly in front of receptor)
Weight
Weight
102 g (3.60 ozs.) (including batteries)
Dimensions
Width : 48 mm (1.89"), Length : 145 mm (5.71"), Height : 27 mm (1.06")
*4 This is an average value. It may differ depending on individual product.
*5 Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*6 [LAMP POWER] will be switched to [ECO1] automatically when the operating environment temperature is 35 °C to 40 °C.
Note
f
The part numbers of accessories and separately sold components are subject to change without notice.
ENGLISH - 133
Chapter 6 Appendix - Specifications
INF-1
CONTENTS
Service Information
Model No. PT-VW345NZ
PT-VX415NZ
SECTION 1 SERVICE INFORMATION
(2013-11)
SECTION 1 SERVICE INFORMATION
1. The name of each part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-2
1.1 Projector body
1.2 Control panel / Indicators
1.3 Connecting terminals
1.4 Remote controls
1.2 Control panel / Indicators
1.3 Connecting terminals
1.4 Remote controls
2. Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-6
3. Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-10
3. Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-10
3. 1. Setting to Service Mode
3. 2. Cancelling the Service Mode
3. 3. Functions of Service Mode
3. 2. Cancelling the Service Mode
3. 3. Functions of Service Mode
4. External Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-13
4. 1. Control through Serial terminal
4. 2. Control through LAN terminal
4. 3. Control commands List
4. 2. Control through LAN terminal
4. 3. Control commands List
5. Notes on service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-18
5. 1. Before service operation
5. 2. Service
5. 3. Replacement of consumable parts
5. 2. Service
5. 3. Replacement of consumable parts
6. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-23
6. 1. Shutdown system
6. 2. Troubleshooting
6. 2. Troubleshooting
INF-2
SECTION 1 SERVICE INFORMATION
1. The name of each part
1.1 Projector body
Zoom ring (Back)
1
Adjust the zoom.
Control Panel and Indicators (
Control Panel and Indicators (
2
Æ
page 27)
Lamp cover (
3
Æ
page 118)
The lamp unit is located inside.
Projection Lens
Projection Lens
4
Attention
Do not drop the remote control.
f
Avoid contact with liquids.
f
Do not attempt to modify or disassemble the remote control.
f
Please observe the following contents that are described on
f
the back of the remote control unit (see the right picture).
1. Do not use a new battery together with an old battery.
2. Do not use unspecified batteries.
3. Make sure the polarities (+ and -) are correct when inserting the batteries.
In addition, please read the contents that are related to batteries in the "Read this first!".
f
Note
The remote control can be used within a distance of about 7 m (22.97') if pointed directly at the remote control signal
f
receiver. The remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control
range may be reduced.
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not
f
operate correctly.
You can operate the projector by reflecting the remote control signal on the screen. The operating range may differ due to
f
the loss of light caused by the properties of the screen.
When the remote control signal receiver is lit with a fluorescent light or other strong light source, the projector may become
f
inoperative. Set the projector as far from the luminous source as possible.
Projector body
WARNING
Keep your hands and other objects away from the air
exhaust port.
Keep your hand and face away.
f
Do not insert your finger.
f
Keep heat-sensitive articles away.
f
Heated air from the air exhaust port can cause burns or
Heated air from the air exhaust port can cause burns or
external damage.
Focus ring (Front)
5
Adjust the focus.
Remote control signal receiver/Camera
Remote control signal receiver/Camera
6
Air exhaust port
7
Speaker
8
<AC IN> terminal
9
Connect the supplied power cord.
Rear terminals (
Rear terminals (
10
Æ
page 28)
Air intake port / Air filter cover (
11
Æ
page 116)
The air filter unit is inside.
Adjustable feet
Adjustable feet
12
Adjust the projection angle.
Security Chain Hook
Security Chain Hook
13
Attaches a burglar prevention cable, etc.
Attention
Do not block the ventilation ports (intake and exhaust) of the projector.
f
1
2
3
4
6
7
8
9
10
11
12
5
13
1. 请勿把旧电池和新电池一起使用。
2. 请勿使用不合规格的电池。
3. 确保电池安装正确。
原产地：中国
1.Do not use old battery with new one.
2.Do not use batteries other than the
2.Do not use batteries other than the
type specified.
3.Be sure the batteries are inserted properly.
3.Be sure the batteries are inserted properly.
Made in China
26 - ENGLISH
Chapter 1 Preparation - About your projector
Some of the pages on this section are excerpted from the owner's
manual, thus the reference page numbers on pages indicate those
for owner's manual .
INF-3
SECTION 1 SERVICE INFORMATION
1.2 Control panel / Indicators
Control panel and Indicators
r
<
1 v/b> button
Turns the projector on/off.
<ON(G)/STANDBY(R)> indicator
<ON(G)/STANDBY(R)> indicator
2
Displays the status of the power.
<LAMP> indicator
<LAMP> indicator
3
Lights red when the projection lamp reaches its end of
life.
<WARNING> indicator
<WARNING> indicator
4
Indicates the abnormal conditions of the projector.
Ambient Luminance sensor
Ambient Luminance sensor
5
Detects room's light and select proper image quality.
<MENU> button
<MENU> button
6
Displays the menu screen. (
Æ
page 54)
<ENTER> button
7
Executes the selected item.
asqw
asqw
8
buttons
Navigates the menu screen.
Adjusts the volume level (qw).
<INPUT SELECT> button
<INPUT SELECT> button
9
Selects the input signal for projection. (
Æ
page 48)
<EASY SETTING/CANCEL> button
10
Executes the EASY SETTING function.
In addition, it acts as <CANCEL> button when using the
MEMORY VIEWER function.
1
2
3
4
5
6
7
8
9
10
ENGLISH - 27
Chapter 1 Preparation - About your projector
Click on the first or last page to see other PT-VW345NZ / PT-VW345NZD / PT-VX415NZ / PT-VX415NZD service manuals if exist.