Panasonic PT-TW370 / PT-TX430 / PT-TX340 Service Manual ▷ View online
9
PREFACE
<TW370/TX430/TX340>
108 - ENGLISH
r
Compatible signals
Refer to “List of compatible signals” of Operating Instructions for the types of video signals that can be used with the projector.
For Video signal
Horizontal : 15.73 kHz, Vertical : 59.94 Hz
Horizontal : 15.63 kHz, Vertical : 50.00 Hz
Horizontal : 15.63 kHz, Vertical : 50.00 Hz
For Y/C signal
Horizontal : 15.73 kHz, Vertical : 59.94 Hz
Horizontal : 15.63 kHz, Vertical : 50.00 Hz
Horizontal : 15.63 kHz, Vertical : 50.00 Hz
For RGB signal
Horizontal 15 kHz - 91 kHz, Vertical 24 Hz - 85 Hz
Dot clock frequency: 162 MHz or less
Dot clock frequency: 162 MHz or less
For YC
B
C
R
/YP
B
P
R
signal
Displayable resolution: 480i/576i to 1 920 x 1 080
Dot clock frequency: 148.5 MHz or less
Dot clock frequency: 148.5 MHz or less
For HDMI signal
Displayable resolution for movie-based signals: 480i/576i
*1
to 1 920 x 1 080
Displayable resolution for still image signals: 640 x 480 to 1 920 x 1 200 (non-interlaced)
Dot clock frequency: 25 MHz to 162 MHz
Dot clock frequency: 25 MHz to 162 MHz
*1 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
Chapter 7 Appendix - Specifications
10
PREFACE
<TW370/TX430/TX340>
r
Dimensions
ENGLISH - 109
Dimensions
Unit : mm (inch)
63 (2-15
/32")
57 (2-1/4")
69 (2-23/32")
335 (13-3/16")
124 (4-7/8")
329 (12-1
5/16")
10 (13/32")
97 (3-13/16")
88 (3-15/32")
134 (5-9/32")
168 (6-5/8")
Actual dimension may differ by product.
Chapter 7 Appendix - Dimensions
SECTION
1
INF-1
(2018-12)
CONTENTS
1. Circuits Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-2
1. 1. Thermal switch
1. 2. Lamp cover switch
1. 3. Fuse (F2003)
1. 2. Lamp cover switch
1. 3. Fuse (F2003)
2. Maintenance/Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-3
2. 1. Maintenance
2. 2. Replacing the Unit
2. 3. How to check the lamp runtime
2. 4. Cleaning
2. 2. Replacing the Unit
2. 3. How to check the lamp runtime
2. 4. Cleaning
3. Notes on service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-10
3. 1. Before service operation
3. 2. Service
3. 3. Security functions
3. 4. Standby mode
3. 5. How to change the baud rate of serial communication port
3. 2. Service
3. 3. Security functions
3. 4. Standby mode
3. 5. How to change the baud rate of serial communication port
4. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-14
4. 1. LED indicators
4. 2. Shutdown system
4. 3. Error log
4. 4. Troubleshooting
4. 5. I/O port functions
4. 2. Shutdown system
4. 3. Error log
4. 4. Troubleshooting
4. 5. I/O port functions
SECTION 1 SERVICE INFORMATION
INF-2
SECTION 1 SERVICE INFORMATION
<TW370/TX430/TX340>
1. Circuits Protection
This projector provides the following circuit protections to operate in safety. If the abnormality occurs inside the projector, it will auto-
matically turn off by operating one of the following protection circuits.
1. 1. Thermal switch
There is a thermal switch inside of the projector to detect the
internal temperature rising abnormally. When the internal tem-
perature around lamp reaches near 120°C , the thermal switch
will open to cut off the power supply to the lamp power circuit.
The thermal switch is not reset to normal automatically even if the
internal temperature becomes normal. Please reset the thermal
switch following to the procedure below.
How to reset the thermal switch
1. Remove the cabinet top case.
2. Press the reset button on the thermal switch.
Caution:
Before press the reset button, disconnect the AC cord from the
projector.
1. 2. Lamp cover switch
The lamp cover switch cuts off the drive signal to the lamp circuit
when the lamp cover is removed or not closed completely. After
opening the lamp cover for replacing the lamp unit, place the
lamp cover correctly otherwise the projector cannot turn on.
1. 3. Fuse (F2003)
A fuse is located inside of the projector. When the <ON (G)/
STANDBY (R) > indicator is not lighting, the fuse may be opened.
Please check the fuse as following steps.
The fuse should be used with the following type;
Fuse Part No.: K5E632YY0007
TYPE VBS UBM 6.3A 250V (PF) FUSE
CONQUER. TYPE VBS UBM
How to replace the fuse
1. The fuse is placed on the filter board. Remove the cabinet
top according to the section 2 "Mechanical Disassembly".
2. Take the fuse off from the fuse holder, then replace the new
one with the specified type.
Thermal fuse
Lamp cover switch
Lamp cover switch
Fuse
(F2003)
Click on the first or last page to see other PT-TW370 / PT-TX430 / PT-TX340 service manuals if exist.