DOWNLOAD Panasonic PT-RZ970 / PT-RW930 / PT-RX110 (serv.man6) Service Manual ↓ Size: 35.32 MB | Pages: 125 in PDF or view online for FREE

3

There are special components used in this equipment which are important for safety. These parts are marked by 7 in the schematic 

diagram, circuit board diagrams, exploded views and replacement parts list. It is essential that these critical parts should be replaced 

with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original design without permission of 

manufacturer.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

f

 Move the lens position to the home position and attach the lens protection material when transporting.

   The projector with the lens sold separately, move the lens position to the home position, remove the projection

   lens, and attach the lens hole cover when transporting. 
f

 Hold the bottom of the projector and do not hold the projection lens or the opening around the projection 

lens when transporting. Failure to do so may cause damage. Also, handle the projector in a way not to apply 

excessive vibration or shock. Failure to do so may cause a failure due to the damaged internal components.

 

f

Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

r

Not doing so may cause failure due to accumulating dust internally.

r

The projector is designed for indoor use only.

r

 

f

Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal 

components or malfunction.

 

f

Location close to sea or where corrosive gas may occur: The projector may fall due to corrosion. Also, failure to 

do so may shorten the life of the components and result in malfunction.

 

f

Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare 

cases due to the heated air from the air exhaust port or the hot or cooled air from the air conditioner. Make sure 

that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward 

the front of the projector.

 

f

Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of 

the light source, or result in deformation of the projector due to heat, which may cause malfunctions.
Follow the operating environment temperature of the projector.

 

f

Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.

 

f

Places where there is high-power laser equipment: Directing a laser beam onto the projection lens surface 

causes damage to the DLP chips.

4

r

The optional Ceiling Mount Bracket is required.
Model No.: ET-PKD120H (for High Ceilings), ET-PKD120S (for Low Ceilings), ET-PKD130H (for High Ceilings, 

6-axis Adjustment), ET-PKD130B (Projector Mount Bracket)

r

Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate 

installation.

r

If there is any facility or equipment which outputs strong radio waves near the installation location, install the 

projector at a location sufficiently far from the source of the radio waves. Or, wrap the LAN cable connected to the 

<DIGITAL LINK/LAN> terminal using a piece of metal foil or a metal pipe which is grounded at both ends.

r

The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in 

the period just after switching on the power. It is recommended that images be projected continuously for at least 

30 minutes before the focus is adjusted.

r

r

Using the projector in a location that the altitude is too high or the ambient temperature is too high may reduce the 

life of the components or result in malfunctions.

r

360°

360°

360°

360° vertically

360° horizontally

360° tilted

(combination of vertical and horizontal)

r

The geometric adjustment function cannot be used when projecting the input signal rotated by 90°. When 

installing the projector, follow the following instructions to prevent distortion in the projected image.
f

 Use a flat screen.

f

 Install the projector so that the front side of the projector is parallel to the screen.

f

 Install the projector so that the image can be projected within the range of shift adjustment by moving the lens 

position.

The 90° rotation of the image can be set in the [DISPLAY OPTION] menu → [IMAGE ROTATION]

5

r

f

 Use the adjustable feet only for the floor standing installation and for adjusting the angle. Using them for other 

   purposes may damage the projector. 
f

 When installing the projector with a method other than the floor installation using the adjustable feet, top placed

   on the floor, or the ceiling installation, use the five screw holes for ceiling mount (as shown in the figure) to fix   

   the projector to the mount.

   (Screw diameter: M6, tapping depth inside the projector: 12 mm (15/32"), torque: 4 ± 0.5 N·m)

6

1. Safety Precautions
2. Specifications

1. The name of each part
2. Menu Navigation
3. Service Mode
4. Notes on service
5. Troubleshooting

1. Parts Locations
2. Disassembly Instructions

1. Adjustment item and a procedure
2. Firmware Update Procedure