Panasonic PT-RZ670 / PT-RW630 (serv.man4) Service Manual / Other ▷ View online
SECTION 2 DISASSEMBLY PROCEDURES
< RZ670/RW630 >
3. 1) Remove the fixing screws of the each terminals. (6 screws)
2) Unscrew the 5 screws and remove the DG-P.C.Board.
The DG-P.C.Board is directly connected to the A-P.C.Board with the connector. Be careful when removing.
3) Unscrew the 1 screw and remove the M1-P.C.Board.
4. 1) Remove the fixing screws of the each terminals. (8 screws)
2) Unscrew the 5 screws and remove the A-P.C.Board.
2. 6. Removal of LD Driver Block (D-P.C.Board / DR-P.C.Board)
1. Remove the signal processing block according to the section 2.5 "Removal of Signal Processing Block
(DG-P.C.Board / A-P.C.Board)".
2. Unscrew the 3 screws and remove the Exhaust fan block.
Note :
DG-P.C.Board
M1-P.C.Board
Terminal metal panel
Terminal metal panel
A-P.C.Board
Exhaust fan Block
5
1
6
5
1
2
4
1
3
DIS-9
SECTION 2 DISASSEMBLY PROCEDURES
<RZ670J/RW630J>
3. Unscrew the 5 screws and remove the LD drive block.
4. 1) Remove the 2 clips and remove the Sheet1.
2) Unscrew the 2 screws and remove the DR-P.C.Board.
5. Unscrew the 4 screws and remove the D-P.C.B top plate.
LD drive block
Sheet1
DR-P.C.Board
D-P.C.B. top plate
5
2
4
DIS-10
SECTION 2 DISASSEMBLY PROCEDURES
< RZ670/RW630 >
6. Unscrew the 2 screws and remove the D-P.C.B (LD2).
7. Unscrew the 2 screws and remove the D-P.C.B (LD1).
2. 7. Removal of Power Supply Block
1. Remove the signal processing block according to the section 2.5 "Removal of Signal Processing Block
(DG-P.C.Board/A-P.C.Board)".
2. Unscrew the 6 screws and remove the Power Supply Block.
2. 8. Removal of DMD Block (FM-P.C.Board / DMD Chip / Trim Wheel)
1. Remove the front cover according to the section 2.4 "Removal of Side cover (L) / Side cover (R) / Front cover / Rear cover).
2. Unscrew the 3 screws and remove the Lens cover.
D-P.C.Board
（LD1）
D-P.C.Board
（LD2）
Power supply block
Lens cover
4
4
6
3
DIS-11
SECTION 2 DISASSEMBLY PROCEDURES
< RZ670/RW630 >
3. Unscrew the 3 screws and remove the Trim wheel cover.
[Coution] ・Carefully pull out the flex cable of trim wheel from the through slit of the dust protection sheet.
・When re-assembling, make sure flex cable is properly placed without stackness.
1) Unscrew the 2 screws and remove the Trim plate.
2) Unscrew the 3 screws and remove the Trim wheel.
（Torque:22±2 N・cm）
4. Unscrew the 6 screws and remove the DMD block.
[ Caution ]
・Refer section 2.1 to remove the flexible cables.
5. Unscrew the 4 screws and remove the heat-sink.
[ Note for re-assembling ]
1) Evenly put heat compound on the attaching surface of heat sink.
2) Take care the compound not overflowing.
Trim wheel cover
DMD block
Put heat compound
Heat compound : Shinnetsu Silicon X-23-7898D
Heat-sink
Heat-sink
Smaller R of
spring to screw head
spring to screw head
3
6
4
3
2
DIS-12
Click on the first or last page to see other PT-RZ670 / PT-RW630 (serv.man4) service manuals if exist.