Panasonic PT-RZ670 / PT-RW630 (serv.man14) Service Manual / Other ▷ View online
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
1. The name of each part
1. 1. Projector body
1
2
3
4
5
6
7
7
10
8
8
11
9
16
17
14
13
15
7
7
7
Front
Side
Rear
8
8
8
12
Projection direction
Bottom
1 Remote control signal receiver (front)
2 Power indicator <ON (G)/STANDBY (R)>
Displays the status of the power.
3 Light source indicator <LIGHT1>
Displays the status of light source 1.
4 Light source indicator <LIGHT2>
Displays the status of light source 2.
5 Temperature indicator <TEMP>
Displays the internal temperature status.
6 (Not available with this projector)
7 Adjustable
feet
Adjusts the projection angle.
8 Air intake port
9 Projection
lens
(Only models with lens)
10 Remote control signal receiver (rear)
11 Air exhaust port
12 Burglar hook port
Attaches a burglar prevention cable, etc.
13 Control
panel
14 Connecting
terminals
15 Security
slot
This security slot is compatible with the Kensington security
cables.
cables.
16 <MAIN POWER> switch
Turns on/off the main power.
17 <AC IN> terminal
Connect the supplied power cord.
Attention
f Do not block the ventilation ports (intake and exhaust) of the projector.
INF - 2
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
1. 2. Control panel
1. 3. Connecting terminals
9
10
11
12
13
14
2
4
3
1
5
6
7
8
1 Power on <
b> button
Starts projection when the <MAIN POWER> switch on the
projector is set to <ON> when the power is switched off
(standby mode).
projector is set to <ON> when the power is switched off
(standby mode).
2 Power standby <
v> button
Sets the projector to the state where the projector is switched
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
3 <RGB1>
button
Switches the input to RGB1.
4 <RGB2>
button
Switches the input to RGB2.
5 <DVI-D>
button
Switches the input to DVI-D.
6 <HDMI>
button
Switches the input to HDMI.
7 <DIGITAL LINK> button
Switches the input to DIGITAL LINK.
8 <SDI>
button
Switches the input to SDI.
(Only for PT-RZ670)
(Only for PT-RZ670)
9 <MENU>
button
Displays or hides the main menu.
Returns to the previous menu when a sub-menu is displayed.
If you press the <MENU> button on the control panel for at least
three seconds while the on-screen display is off (hidden), the
on-screen display is turned on.
If you press the <MENU> button on the control panel for at least
three seconds while the on-screen display is off (hidden), the
on-screen display is turned on.
10 <LENS>
button
Adjusts the focus, zoom, and shift (position) of the lens.
11 <ENTER>
button
Determines and executes an item in the menu screen.
12 <SHUTTER>
button
Used to temporarily turn off the image.
13
asqw buttons
Used to select items in the menu screen, change settings, and
adjust levels.
Also used to enter a password in [SECURITY] or enter
characters.
Used to select items in the menu screen, change settings, and
adjust levels.
Also used to enter a password in [SECURITY] or enter
characters.
14 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image. [PROGRESS] is displayed while in automatic
adjustment.
the image. [PROGRESS] is displayed while in automatic
adjustment.
1
2
3
4
5
6
7
8
9
10
1 <REMOTE 1 IN> terminal/<REMOTE 1 OUT> terminal
These are the terminals to connect the remote control for serial
control in a multiple projector environment.
control in a multiple projector environment.
2 <REMOTE 2 IN> terminal
This is a terminal to remotely control the projector using the
external control circuit.
external control circuit.
3 <SERIAL IN> terminal
This is the RS-232C compatible terminal to externally control
the projector by connecting a computer.
the projector by connecting a computer.
4 <SERIAL OUT> terminal
This is a terminal to output the signal connected to the <SERIAL
IN> terminal.
IN> terminal.
5 <SDI IN> terminal
This is the terminal to input SDI signals.
(Only for PT-RZ670)
(Only for PT-RZ670)
6 <RGB 1 IN> (<R/P
R
/VIDEO>, <G/Y>, <B/P
B
/C>, <SYNC/HD>,
<VD>) terminals
These are terminals to input RGB signals, YC
These are terminals to input RGB signals, YC
B
C
R
/YP
B
P
R
signals, Y/C signals, or video signals.
7 <RGB 2 IN> terminal
This is a terminal to input RGB signals or YC
B
C
R
/YP
B
P
R
signals.
8 <DVI-D IN> terminal
This is the terminal to input DVI-D signals.
9 <HDMI IN> terminal
This is the terminal to input HDMI signals.
10 <DIGITAL LINK/LAN> terminal
This is the LAN terminal to connect to the network. This is also
used when connecting a video signal transmission device via
the LAN terminal.
used when connecting a video signal transmission device via
the LAN terminal.
Attention
f When a LAN cable is directly connected to the projector, the network connection must be made indoors.
INF - 3
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
1. 4. Remote control
1
3
2
4
5
7
6
8
9
10
15
12
11
13
14
14
16
17
Front
Top
Bottom
1 Power standby <
v> button
Sets the projector to the state where the projector is switched
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
2 Power on <
b> button
Starts projection when the <MAIN POWER> switch on the
projector is set to <ON> when the power is switched off
(standby mode).
projector is set to <ON> when the power is switched off
(standby mode).
3 Remote control indicator
Blinks if any button in the remote control is pressed.
4 Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons
Adjusts the projection lens.
5 <MENU> button/<ENTER> button/
asqw buttons
Used to navigate through the menu screen.
6 <ON SCREEN> button
Switches the on-screen display function on (display) or off
(hide).
(hide).
7 Input selection (<RGB1/2>, <DIGITAL LINK>, <DVI-D>,
<VIDEO>, <SDI>, <HDMI>) buttons
Switches the input signal to project.
Switches the input signal to project.
(SDI input is supported only for PT-RZ670.)
8 <FUNCTION>
button
Assigns a frequently used operation as a shortcut button.
9 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
projector environment.
10 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed while in automatic adjustment.
the image.
[PROGRESS] is displayed while in automatic adjustment.
11 <SHUTTER>
button
Used to temporarily turn off the image.
12 <TEST PATTERN> button
Displays the test pattern.
13 <STATUS>
button
Displays the projector information.
14 <DEFAULT>
button
Resets the content of the sub-menu to the factory default.
15 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment.
environment.
16 Remote control signal transmitter
17 Remote control wired terminal
This is the terminal used to connect to the projector via a cable
when used as a wired remote control.
when used as a wired remote control.
Attention
f Do not drop the remote control.
f Avoid contact with liquids or moisture.
f Do not attempt to modify or disassemble the remote control.
Note
f When operating the remote control by directly pointing at the remote control signal receiver of the projector body, operate the remote
control within a distance approx. 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30°
vertically and horizontally, but the effective control range may be reduced.
vertically and horizontally, but the effective control range may be reduced.
f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
f
. Use
it in a place distant from the light source.
f The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
f The operation of the <VIDEO> button is disabled in the factory default settings. The operation is enabled when [REMOTE CONTROL] is set
to [USER] and [VIDEO BUTTON] of [INPUT SELECT BUTTON] is set to other than [DISABLE], from the [SECURITY] menu
→ [CONTROL
DEVICE SETUP]
INF - 4
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
2. OSD Menu Navigation
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu selection screen.
Main menu item
[PICTURE]
[POSITION]
[ADVANCED MENU]
[DISPLAY LANGUAGE]
[DISPLAY OPTION]
[PROJECTOR SETUP]
[P IN P]
[TEST PATTERN]
[SIGNAL LIST]
[SECURITY]
[NETWORK]
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
[PICTURE]
Sub-menu item
Factory default
[PICTURE MODE]
[STANDARD]
*1
[CONTRAST]
[0]
[BRIGHTNESS]
[0]
[COLOR]
[0]
[TINT]
[0]
[COLOR TEMPERATURE]
[DEFAULT]
[WHITE GAIN]
[+10]
[GAMMA]
[DEFAULT]
[SYSTEM DAYLIGHT VIEW]
[OFF]
[SHARPNESS]
[+6]
[NOISE REDUCTION]
[OFF]
[DYNAMIC CONTRAST]
[2]
[SYSTEM SELECTOR]
[YP
B
P
R
]
*1
*1 Depends on the signal input.
Note
f The factory default settings may vary depending on the picture mode.
INF - 5