DOWNLOAD Panasonic PT-RZ570 (serv.man2) Service Manual ↓ Size: 28.22 MB | Pages: 98 in PDF or view online for FREE

1-chip DLP Based  Projector

ORDER NO. VED1603598CE

■ This service manual is common to the models regardless of suffixes of the Model No.

• for Taiwan

BT: Black model WT: White model

• for India

BD: Black model WD: White model

• for for Asia (except for Taiwan, India, Korea) / Oceania / Africa

BA: Black model WA: White model

• for other countries or regions

B: Black model W: White model

■ Illustrations in this service manual

• Illustrations of the projector, screen, and other parts may vary from the actual product.

• Illustrations of the projector with the power cord attached are only examples.

The shape of the supplied power cords varies depending on the country where you purchased the product.

Model No.

 

PT-RZ570

2

 

 

This projector is using the P.C.Board which applies lead free solder.

 

 

Use lead free solder in servicing from the standpoint of antipollution for the global environment.

 

 

Notes:

 

 

•  Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder Typically 

the melting point is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation func-

tion and set it to 370 ± 10 °C.

 

 

•  Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 

600°C or higher).

 

 

•  Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead 

solder, use lead solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before 

applying lead solder.)

 

 

•  After solder to double layered P.C Boards, check the component side for excess solder which may flow onto the opposite side.

 

 

About the identification of the lead free solder P.C.Board.

 

 

 For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface 

or the back of P.C.Board.

PbF

DPQT1023ZA

Éユチュユチロトリヮヱヶロヴリヰワホヒハパㄎㄔ

The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.

Le technicien d'entretien doit lire et suivre les «Précautions de sécurité» et «Avis important de sécurité» dans ce manuel d'entretien.

7

This service information is designed for experienced repair technicians only and is not designed for use by the general public.

It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Prod-

ucts powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair 

the product or products dealt with in this service information by anyone else could result in serious injury or death.

7

 

Ce document d'entretien est destiné aux techniciens d'entretien expérimentés uniquement et n'est pas conçu pour une utilisation par le 

grand public. Il ne contient pas des avertissements ou des mises en garde pour aviser les non-techniciens des dangers potentiels lorsqu'ils 

tentent de réparer un produit. Les appareils alimentés par l'électricité doivent être révisés ou réparés uniquement par des techniciens pro-

fessionnels expérimentés. Toute tentative d'entretenir ou de réparer le ou les produits traités dans ce document d'entretien par autrui peut 

entraîner des blessures graves ou la mort.

 

 

Risk of explosion if battery is replaced by an incorrect type,

 

 

Replace only with the same of equivalent type recommended by the manufacturer.

 

 

Dispose of used batteries according to the manufacturer’s instructions.

 

 

Risque d'explosion si la batterie est remplacée par un type incorrect,

 

 

Remplacez-la uniquement par le même type ou le type équivalent recommandé par le fabricant.

 

 

Jetez les batteries usagées conformément aux instructions du fabricant.

TQFX608

3

There are special components used in this equipment which are important for safety. These parts are marked by 7 in the schematic 

diagram, circuit board diagrams, exploded views and replacement parts list. It is essential that these critical parts should be replaced 

with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original design without permission of 

manufacturer.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

 

f

When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. They 

may damage the internal components and result in malfunctions.

 

f

Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

r

The projector is designed for indoor use only.

r

 

f

Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal 

components or malfunction.

 

f

Location close to sea or where corrosive gas may occur: The projector may fall due to corrosion. Also, failure to 

do so may shorten the life of the components and result in malfunction.

 

f

Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare 

cases due to the heated air from the air exhaust port or the hot or cooled air from the air conditioner. Make sure 

that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward 

the front of the projector.

 

f

Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of 

the light source, or result in deformation of the projector due to heat, which may cause malfunctions.
Follow the operating environment temperature of the projector.

 

f

Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.

 

f

Places where there is high-power laser equipment: Directing a laser beam onto the projection lens surface 

causes damage to the DLP chips.

4

r

The optional Ceiling Mount Bracket is required.
Model No.: ET-PKD120H (for High Ceilings), ET-PKD120S (for Low Ceilings), ET-PKD130B (Projector Mount 

Bracket)

r

Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate 

installation.

r

If there is any facility or equipment which outputs strong radio waves near the installation location, install the 

projector at a location sufficiently far from the source of the radio waves. Or, wrap the LAN cable connected to the 

<DIGITAL LINK/LAN> terminal using a piece of metal foil or a metal pipe which is grounded at both ends.

r

The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in 

the period just after switching on the power. It is recommended that images be projected continuously for at least 

30 minutes before the focus is adjusted.

r

r

Using the projector in a location that the altitude is too high or the ambient temperature is too high may reduce the 

life of the components or result in malfunctions.
The upper limit of the operating environment temperature differs depending on the altitude or the setting of the 

[PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [OPERATING MODE].

Altitude of 0 m (0') or higher to lower 

than 1 400 m (4 593')

0 °C (32 °F) to 45 °C (113 °F)

Altitude of 1 400 m (4 593') or higher to 

lower than 2 700 m (8 858')

0 °C (32 °F) to 40 °C (104 °F)

Altitude of 2 700 m (8 858') or higher to 

lower than 4 200 m (13 780')

0 °C (32 °F) to 40 °C (104 °F)

The projector cannot be used.

r

360°

360°

360°

360° vertically

360° horizontally

360° tilted

(combination of vertical and horizontal)

r

 

f

Use the adjustable feet only for the floor standing installation and for adjusting the angle. Using them for other 

purposes may damage the projector.

 

f

When installing the projector with a method other than the floor installation using the adjustable feet or the 

ceiling installation, use the five screw holes for ceiling mount (as shown in the figure) to fix the projector to the 

mount. (Screw diameter: M6, tapping depth inside the projector:15 mm (19/32"), torque: 4 ± 0.5 N·m)