Panasonic PT-RZ370U / PT-RZ370E / PT-RZ370EA / PT-RW330U / PT-RW330E / PT-RW330EA (serv.man8) Service Manual ▷ View online
5. When assembling, the sponge of a lighting top case sticks a new sponge on the original position.
ⓐ ： TMKH589 × 8
ⓑ ： TMKH512 × 1
< Reference > Wiring diagram
ⓑ
ⓐ
ⓐ
ⓐ
ⓐ
ⓐ
ⓐ
ⓐ
ⓐ
DIS-14
2.10. Procedure for Assembling of LD unit and Heat-pipe unit
2.10.0. Preparation
Necessary tools and grease
No.
4
Spatula
For painting the grease
5
Grease
・ Please make sure to use the grease below for
assembling LD unit and Heat-pipe.
Please purchase this grease locally.
[Information of grease]
Manufacturer : Shin-Etsu Chemical Co.,Ltd
Item : Thermal Interface compounds
Manufacturer : Shin-Etsu Chemical Co.,Ltd
Item : Thermal Interface compounds
(High reliability)
Model : G-776
Packing : 100g or 1kg
Packing : 100g or 1kg
Please contact
service department of VSBD
for the detail.
service department of VSBD
for the detail.
2
Torque driver ( 60 cN・m ~ 80 cN・m)
Bits ( +bit No.1, + bit No.2 )
3
LD GREASE MASK PLATE
Part No. : TZSH0703
9
Item
Trmark
1
Philips screw driver (Normal ones)
DIS-15
2.10.1. Greasing for Heat-pipe unit
1. Set a LD GREASE MASK PLATE on a Heat-pipe unit by clips as shown below.
2. Paint the grease on the Heat-pipe unit by spatula.
3. Remove the LD GREASE MASK PLATE.
LD GREASE MASK PLATE
Heat-pipe unit
Please make sure that the boss of
the Heat-pipe is fitted into the
hole of the plate.
the Heat-pipe is fitted into the
hole of the plate.
Clip
Clip
Please make sure that the plate is
flat and attached to the Heat-pipe.
flat and attached to the Heat-pipe.
Heat-pipe unit
Paint the grease over the entire
surface of orange area of heat-pipe
surface of orange area of heat-pipe
Paint the grease on the heat-pipe with
the same thickness as the plate.
the same thickness as the plate.
Heat-pipe unit
LD GREASE
MASK PLATE
DIS-16
2.10.2. Greasing for Heat-pipe unit
< Caution for LD unit >
Don't put a LD unit on the desk otherwise LD lenses may be damaged.
Don't put a LD unit on the desk otherwise LD lenses may be damaged.
Please prepare some pedestals and use these as shown below.
Don't touch the LD lenses on the LD unit.
Don't touch the terminal of flexible cable on the LD unit.
Don't touch the LD lenses on the LD unit.
Don't touch the terminal of flexible cable on the LD unit.
1. Set the LD unit on a Pedestal.
2. Set the Heat-pipe unit on the LD unit.
3. Tighten 4 screws A (Original silver screws with washers) by torque driver.
LD lenses
Don’t touch the LD lenses.
Don’t touch the terminal
Don’t put the LD unit on the desk
LD unit
Pedestal
Edge
Edge
LD unit
Pedestal
Heat-pipe unit
Screw A
.
Tightening torque
Screw A : 70
Screw A : 70
10 cNm
DIS-17
Click on the first or last page to see other PT-RZ370U / PT-RZ370E / PT-RZ370EA / PT-RW330U / PT-RW330E / PT-RW330EA (serv.man8) service manuals if exist.