DOWNLOAD Panasonic PT-RZ370U / PT-RZ370E / PT-RZ370EA / PT-RW330U / PT-RW330E / PT-RW330EA (serv.man8) Service Manual ↓ Size: 20.55 MB | Pages: 82 in PDF or view online for FREE

  2. SELF CHECK

・ Each self check item is displayed.

SELF CHECK

MAIN : 1.00.00   SUB : 1.00.00

Main, Sub microprocessor software version

NETWORK : 1.00.00   FPGA : 0x2A

Network and FPGA software version

BALLAST : 230  DIGITAL LINK : 1.30.33.1

BALLAST and DIGITAL LINK software version

EMULATE : DEFAULT

Setting and Version of EMULATE

OK

INTR.   026/224

Internal air temperature check (Celsius/Fahrenheit)

OK

INTK.   041/151

Intake air temperature check (Celsius/Fahrenheit)

OK

DMD.    054/104

DMD temperature check (Celsius/Fahrenheit)

OK

TEMP_R  036/101

LED-R temperature check (Celsius/Fahrenheit)

OK

TEMP_G  036/101

LD unit temperature check (Celsius/Fahrenheit)

OK

TEMP-B  036/101

LED-B temperature check (Celsius/Fahrenheit)

OK

WIND.   075/054/+5

Airflow sensor check (Sensor, AD conversion, Correction value)

OK

LIGHT   200h30m / 1  ON

Light source check (lighting accumulative time, number of times

OK

FAN     1111 11

the replacement, ON-OFF)

OK

PHOSPHOR WHEEL

Fan check (1:Normal/0: Abnormal)

From the left, LD-G, LED-R, LED-B, DMD, EXHAUST, DRIVER

Phosphor wheel check

  3. MODEL

・ Set this when the A-P.C.Board is replaced.

* If you can copy EEPROM data from the old A-P.C.Board, this setting is unnecessary.

* This model setting is changed after power restart.

  4. CLOG SENSOR CALIBRATION

・Calibrate the clogging sensor circuit.

  Execute this after EEPROM（IC1405）/A-P.C.Board or Airflow sensor (M3-P.C.Board） is replaced.

* Refer to the "SECTION3 (ADJUSTMENT PROCEDURE)" about method.

  5. DVI SELECT COMMAND

・Setting for DVI-I input terminal

DVI : Functions as a terminal for DVI input.

(When this item is selected, this terminal can be selected to Digital or Analog with DISPLAY OPTION menu.)

COMPUTER2 : Functions as a terminal for COMPUTER2 input. (Analog mode only.)

  1. "POSITION" menu

The following one item is added.
・DVI EQUALIZER

When noise contamination to DVI input caused by long cable or external device, set this item so that the 

noise decreases.

  2. "ADVANCED" menu.

The following one items are added.
・FRAME LOCK

Set this item when moving picture is disturbed with RGB input.

  3. "DISPLAY OPTION" menu

The following one items are added.
・CUT OFF

Red(R), Green(G), Blue(B) color component is selected and display or non-display set.

* If check items are indicated with "NG" in red, the projector has an abnormality now.
　If the projector has an abnormality in the past and operates normally now, the first self-check screen is indicates
　in red with "OK". (Except fan error.)  Error information is cleared after exiting from self-check mode.

INF - 6

INF - 7

  4. "PROJECTOR SETUP" menu

1) The selections below are added on "Emulate" in the sub menu "RS-232C" setting.

-MODE_HI （Other company products）

-MODE_MI （Other company products）

-MODE_NE （Other company products）

-MODE_SO （Other company products）

-MODE_EP （Other company products）

-MODE_IN （Other company products）

-MODE_SA （Other company products）

-OTHER （Other company products）

-MODE_SH （Other company products）

2) The following items are added on "STATUS" sub menu (page 1/3).

・OPTICS MODULE TEMP.

・EMULATE-VERSION

3) The following items are added on "STATUS" sub menu (page 2/3).

・

FPGA VERSION (software version)

・

BALLAST VERSION (software version)

・

DIGITAL LINK VERSION (software version)

4) This page will be added on "STATUS" sub menu (page 3/3).

・

Displays the temperature of the various parts, and

  the number of fan rotation etc.

  5. "TEST PATTERN" menu

・

 The following test patterns are added.

"Flag", "Reverse flag", "Whole red", "Whole green", "Whole blue", "Whole cyan", "Whole magenta",
 "Whole yellow", "Convergence (RGB bar)” patterns.

INF - 8

●

To connect directly

●

To connect using DIGITAL LINK compatible device

      Note : Interface cable is not a standard accessory. Please purchase locally

Pin

①

②

③

④

⑤

⑥

⑦

⑧

 (Factory default)

⑨

1.　Press MENU button of main body or remote controller.
      Go to Main menu → Projector setup.   In sub menu,
      select "RS-232C" and press ENTER.  
2.　Select communication condition by pressing ▲ ▼ button.
      Set it with pressing ◀ ▶ button.
3.　Press MENU button 3 times and return to regular display.

　　

In case of connecting to PC

NC

NC

NC

NC

DSR

NC

NC

NC

7
8

1
2
3
4
5
6
7
8

Signal level

 

RS-232C standard

Synchronization

 Asynchronous

Baud rate

 

9 600 bps

Parity

 None

Character length

 8 bit

Stop bit

 1 bit 

X Parameter

 None

S Parameter

 None

1

Signal name

Contents

－

 NC

TXD

Transmitting data

－

 ＮＣ

GND

Ground

RXD

Receiving data

－

 NC

CTS

Connected each

other inside

RTS

－

 NC

2
3
4
5
6

The <SERIAL IN> terminal of the projector conforms with RS-232C so that the projector can be connected to and controlled

from a computer.

9

9

Projector

(SERIAL IN terminal)

Computer

(DTE specifications)

D-sub 9pin(Female)

 

Outside view

 

<Computer>

 

D-Sub 9p (male)

 

<Projector connecting terminals>

 

Communication cable (straight)

 

<Computer>

 

D-Sub 9p (male)

 

<Projector connecting terminals>

 

Communication cable (straight)

 

LAN cable (straight)

 

DEGITAL LINK Terminal

 

<DIGITAL LINK compatible device>

 

INF - 9

The transmission from PC starts with STX, ID, Command, Parameter and EXT are sent in order.
Parameter is added depending on the control.

1.　Basic control command (No parameter)

2.　Basic control command (with Parameter)

3.　Basic control command (with sub command)

4.　Calculation

Direction of how to deal the indicated value by parameter

Direction
　

Set the value of indicated value by parameter.

　

Add the indicated value by parameter on current value.

5.　Code

Direction of plus / minus for the indicated value by parameter

Direction
　

The value indicated by parameter is plus. ( If it is 0, set this.)

　

The value indicated by parameter is minus.

6.　Parameter

Indicate the setting or adjustment value with right justification.( 0 is not suppressed.)
For example, indicate "00001" for the setting value "1".

7.　ID for the basic commands

・This projector will respond to the computer only in the following cases.

Respond only when the transmitted ID is matched to this projector's ID.
RESPONSE(ID ALL) in RS232C settings of this projector is ON and the sent ID is ALL.

RESPONSE(ID GROUP) in RS232C settings of this projector is ON.

・Specifically, please refer to "Control Commands List"

8.　Response of basic control commands

In accepted period

It depends on each command.

Out of accepted period or no command

Parameter or REMOTE 2 terminal is active

9.　Note

If a command is transmitted after the light source starts illuminating, there may be a delay in response or the 
command may not be executed. Try sending or receiving any command after 60 seconds.
When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the response
from the projector before sending the next command.
There is a case that it takes some time for responding because of internal processing.
Please set the timeout period to more than 10 seconds until the responses comes back.

1 byte

4 bytes

1 byte

45h

52h

Character

30h

32h

0

E

R

4

E

R

Separator

Parameter

Terminal symbol

(ETX)

1 byte

Sub

d

Calculation

Command

Character

3 bytes

1 byte

Hexadecimal

02h

45h

0

1

31h

34h

Command

(Semi colon)

Undefined length

03h

Code

Hexadecimal

02h

2

52h

Hedder

Command

30h

Terminal symbol

（

STX）

(ETX)

1 byte

3 bytes

1 byte

1 byte

Separator

（

STX）

(Colon)

Hedder

Hedder

ＩＤ

Separator

(Colon)

1 byte

4

1 byte

4 bytes

1 byte

3 bytes

(ETX)

1 byte

5 bytes

1 byte

+

-

Code

=

_( underbar)

03h

34h

ＩＤ

Separator

(Semi colon)

ＩＤ

4 bytes

Separator

(Semi colon)

5 bytes

1 byte

Code

（

STX）

Parameter

Terminal symbol