Panasonic PT-RZ21KE / PT-RS20K Service Manual ▷ View online
5
PREFACE
< RZ21K / RS20K >
CONTENTS
1. Safety Precautions
2. Specifications
SECTION 1 SERVICE INFORMATION
1. The name of each part
2. Menu Navigation
3. Service Mode
4. Notes on service
5. Troubleshooting
SECTION 2 DISASSEMBLY PROCEDURES
1. Parts Locations
2. Disassembly Instructions
<Reference> Wiring connection
SECTION 3 ADJUSTMENTS
1. Adjustment item and procedure
2. Firmware update procedure
For the schematic diagram and parts list, refer to the separated booklet "Schematic diagram" and "Parts List"
respectively.
6
PREFACE
< RZ21K / RS20K >
1. Safety Precautions
1. 1. General Guidelines
- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this projector.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed
and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated or damaged
by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C combi-
nations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.
1. 2. Leakage Current Check
1. Prepare the measuring circuit as shown in Fig.1.
Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75mA or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer
because of a possibility of an electric shock.
M1
M2
Rs
Cs
Rb
10KΩ ±0.1%
0.022µF
±1.0%
Vb
(V) V
Rs: 1500 Ω±0.1%
Cs: 0.22 µF±1.0%
Rb: 500 Ω±0.1%
to T1
or T2
in FIg.2
Weighted leakage current=Vb / 500 (A)
Fig. 1
Isolation transformer
T1
T2
connection
to power outlet
M1
M2
Fig.2
Projector
Measuring
Circuit (Fig.1)
Performance
Voltmeter
(rms reading)
Accurancy:
≤ 2%
Input resistance:
≥ 1 MΩ
Input capacitance: ≤ 200 pF
Frequency range: 15 Hz to 1 MHz
Table. 1
7
PREFACE
< RZ21K / RS20K >
2. Specifications
2. 1 Specifications
The specifications of the projector are as follows.
Power supply
100 V - 120 V / 200 V - 240 V ~ (100 V ‑ 120 V / 200 V ‑ 240 V alternating current), 50 Hz/60 Hz
Power consumption
940 W (9.6 A) / 1 510 W (7.7 A)
Power consumption (during
standby)
When [STANDBY MODE] is set to [ECO]: 0.3 W
When [STANDBY MODE] is set to [NORMAL]: 4 W
When [STANDBY MODE] is set to [NORMAL]: 4 W
DLP chip
Size
PT-RZ21K
24.4 mm (0.96") (aspect ratio 16:10)
PT-RS20K
24.1 mm (0.95") (aspect ratio 4:3)
Display system
DLP chip x 3, DLP projection system
Number of pixels
PT-RZ21K
2 304 000 pixels (1 920 x 1 200 dots)
PT-RS20K
1 470 000 pixels (1 400 x 1 050 dots)
Lens
Optional
Light source
Laser x 2
Light output
20 000 lm
*1 *3
, 21 000 lm (center)
*2 *3
(When [OPERATING MODE] is set to [NORMAL])
Center to corner zone ratio
*1
90 %
Contrast ratio
*1
20 000:1 (when [DYNAMIC CONTRAST] is set to [3])
Color system
7 standards (NTSC/NTSC4.43/PAL/PAL‑N/PAL‑M/SECAM/PAL60)
Projected image size
1.78 m (70") to 25.40 m (1 000")
*4
Image aspect ratio
PT-RZ21K
16:10
PT-RS20K
4:3
Projection method
[FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
Power cord length
3.0 m (118‑1/8")
Outer case
Molded plastic
Outer color
Black
Dimensions
Width
598 mm (23‑17/32") (excluding protrusions)
Height
307 mm (12‑3/32") (with the feet at shortest position)
270 mm (10‑5/8") (excluding the feet and protrusion)
270 mm (10‑5/8") (excluding the feet and protrusion)
Depth
725 mm (28‑17/32") (excluding the protrusion)
Weight
Approx. 49.0 k] (108.0 lbs.)
*5
Noise level
*1
46 dB
Operating
environment
Operating
environment
temperature
0 °C (32 °F) to 50 °C (122 °F)
*6*7
Operating
environment
humidity
10 % to 80 % (no condensation)
Remote
control
Power supply
DC 3 V (AA/R6/LR6 battery x 2)
Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight
Weight
150 ] (5.3 ozs.) (including batteries)
Dimensions
Width: 47.5 mm (1‑7/8"), Height: 181.5 mm (7‑5/32"), Depth: 27.5 mm (1‑3/32")
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2012 international standards.
*2 The value of the light output at the center region of the projected image is extracted based on the light output measurement method defined by the
ISO/IEC 21118:2012 international standards.
*3 When a projection lens other than ET-D75LE95, ET-D75LE90 is used with the power supply voltage of AC 200 V.
*4 When the Zoom Lens (Model No.: ET‑D75LE8) is used, the projected image size for the maximum projection distance will be 1.78 m (70") to
15.24 m (600"). When the Fixed‑focus Lens (Model No.: ET‑D75LE95, ET‑D75LE90) is used, the projected image size for the maximum projection
distance will be 3.05 m (120") to 15.24 m (600").
*5 Average value. Weight varies for each product.
*6 The operating environment temperature should be between 0 °C (32 °F) and 45 °C (113 °F) if the projector is used at an altitude between 1 400 m
(4 593') and 4 200 m (13 780') above sea level.
*7 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [NORMAL] or [ECO], the light output may be
reduced to protect the projector.
f
When using the projector at an altitude lower than 2 700 m (8 858') above sea level: 35 °C (95 °F)
f
When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
Note
f
The light output will decrease to approximately 1/2 when using the projector with AC 100 V to AC 120 V.
f
The model numbers of accessories and optional accessories are subject to change without prior notice.
8
PREFACE
< RZ21K / RS20K >
2. 2 Terminal
<RGB 1 IN> terminal
1 set (BNC x 5 (RGB/YP
B
P
R
/YC
B
C
R
/YC/VIDEO x 1))
RGB signal
0.7 V [p‑p] 75 Ω (SYNC ON GREEN: 1.0 V [p‑p] 75 Ω)
SYNC/HD
SYNC/HD
TTL high impedance, automatic positive/negative
polarity compatible
VD
TTL high impedance, automatic positive/negative
polarity compatible
YP
B
P
R
signal
Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p‑p] 75 Ω
Y/C signal
Y: 1.0 V [p‑p], C: 0.286 V [p‑p] 75 Ω
VIDEO signal
1.0 V [p‑p] 75 Ω
<RGB 2 IN> terminal
1 set, high‑density D‑Sub 15 p (female)
RGB signal
RGB signal
0.7 V [p‑p] 75 Ω (SYNC ON GREEN: 1.0 V [p‑p] 75 Ω)
SYNC/HD
SYNC/HD
TTL high impedance, automatic positive/negative
polarity compatible
VD
TTL high impedance, automatic positive/negative
polarity compatible
YP
B
P
R
signal
Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p‑p] 75 Ω
<DVI-D IN> terminal
1 set, DVI-D 24 p, single link, DVI 1.0 compliant, HDCP compatible
<HDMI IN> terminal
1 set, HDMI 19 p, HDCP compatible, Deep Color compatible
<SDI IN 1> terminal
1 set (BNC)
Single link SD-SDI
Single link SD-SDI
signal
SMPTE ST 259 compliant
Single link HD-SDI
signal
SMPTE ST 292 compliant
Single link 3G-SDI
signal
SMPTE ST 424, 425-2 compliant
Dual link HD-SDI
signal (Link A signal)
SMPTE ST 372 compliant
Dual link 3G-SDI signal
(Link 1 signal)
SMPTE ST 425-3 compliant
<SDI IN 2> terminal
1 set (BNC)
Single link SD-SDI
Single link SD-SDI
signal
SMPTE ST 259 compliant
Single link HD-SDI
signal
SMPTE ST 292 compliant
Single link 3G-SDI
signal
SMPTE ST 424, 425-2 compliant
Dual link HD-SDI
signal (Link B signal)
SMPTE ST 372 compliant
Dual link 3G-SDI signal
(Link 2 signal)
SMPTE ST 425-3 compliant
<MULTI PROJECTOR SYNC
IN> terminal/<3D SYNC 1 IN/
OUT> terminal (dual purpose)
1 set (BNC)
TTL high impedance
When [3D SYNC MODE] is set to output, TTL output: Maximum 10 mA
TTL high impedance
When [3D SYNC MODE] is set to output, TTL output: Maximum 10 mA
<MULTI PROJECTOR SYNC
OUT> terminal/<3D SYNC 2
OUT> terminal (dual purpose)
1 set (BNC)
TTL output: Maximum 10 mA
<SERIAL IN>/ <SERIAL OUT>
terminal
D-Sub 9 p, 1 set each, RS-232C compliant, for computer control
<REMOTE 1 IN>/ <REMOTE 1
OUT> terminal
M3 stereo mini jack, 1 set each, for remote control (wired)/for projector connection control
<REMOTE 2 IN> terminal
1 set, D-Sub 9 p, for contact control
<DIGITAL LINK/LAN> terminal 1 set, RJ‑45, for network and DIGITAL LINK connections (HDBaseT
TM
compliant), PJLink compatible,
100Base-TX, Art-Net compatible, HDCP compatible, Deep Color compatible
<DC OUT 1> terminal/<DC
OUT 2> terminal
2 sets, USB connector (type A), for power supply only (DC 5 V, 2 A total for two sets)
Click on the first or last page to see other PT-RZ21KE / PT-RS20K service manuals if exist.