DOWNLOAD Panasonic PT-RQ22KEJ (serv.man3) Service Manual ↓ Size: 46.88 MB | Pages: 127 in PDF or view online for FREE

Model
PT-RQ22KEJ (serv.man3)
Pages
127
Size
46.88 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / 3-CHIP DLP BASED PROJECTOR
File
pt-rq22kej-sm3.pdf
Date

Panasonic PT-RQ22KEJ (serv.man3) Service Manual ▷ View online

ADJ-11
SECTION 3 ADJUSTMENTS
< RQ22K >
5. Read the Adjusted data file by the following procedure.
    ① Select the projector name to read of Adjusted data.
    ② Select a [Service] tab.
    ③ Click [Receive] button.
  
  
6. Select the save place and click [Save(S)] button.
7. The data save is complete when the "Complete" dialog window appears.
    Click [OK] button to close the window.
ADJ-12
SECTION 3 ADJUSTMENTS
< RQ22K >
1. 4. 4. Restore the backup Adjusted data (after circuit board replace)
1.  Start up service software [LogTool.exe] with a computer according to steps 1 - 4 of "1. 4. 3. Backup the Adjusted data 
(before circuit board exchange)" and connect it to the projector.
2. Restore the Adjusted data file by the following procedure.
    ① Select the projector name to send of Adjusted data.
    ② Select a [Service] tab.
    ③ When replacing [A]-P.C.Board, check-mark [Replace A-Pwb] in "Data Restore".
     When replacing [DG]-P.C.Board, check-mark [Replace DG-Pwb] in "Data Restore".
    ④ Click [Send] button in "Data Restore".
3. Select the saved file and click [OPEN(O)] button.
ADJ-13
SECTION 3 ADJUSTMENTS
< RQ22K >
4.  Once the progress bar reaches the right side end and when the "Complete" dialog window appears, it is a write comple-
tion of the data.
5. Click [OK] button to close the window and quit the software.
• Turn off the main power, turn on the power again, and check that it operates properly.
1. 5. Main-firmware update
f
  After replacing the [A] or [DG], [DF], [DP] printed circuit board, write the latest version of main firmware again to make 
consistency between Main and FPGA firmware.
   Each FPGA firmware is updated at the same time as the main firmware.
f
 For the procedure, refer to "2. Firmware update procedure".
•  Even if the Main firmware is already latest version, the each FPGA firmware may not be  latest version,
so please update again.
ADJ-14
SECTION 3 ADJUSTMENTS
< RQ22K >
1. 6. Model information setup
 1.  Enter the service mode, and select submenu [MODEL] of           
[EXTRA OPTION] menu.
 2.  Press [ a ][ s ] button to select the model, and press the             
[ENTER] button.
 3. The model information will be applied after the main power restart.
 4.  Confirm the model information in the sub menu [STATUS] of the 
menu [PROJECTOR SETUP].
MODEL
WQXGA : PT-RQ22K
WQXGA : PT-RQ22KD
D
WQXGA : PT-SRQ22KC
C
SELECT
SET
ENTER
1. 7. Luminance sensor calibration
1. For proper adjustment, power on the projector for at least 5 minutes with the following settings.
   • [DYNAMIC CONTRAST] of [PICTURE] menu : [OFF]
   • [OPERATION SETTING] of [PROJECTOR SETUP] menu : [NORMAL]
   • [LIGHT OUTPUT] of [PROJECTOR SETUP] menu : [100.0%]
2.  Enter the service mode, and select [PHOTO SENSOR CALIBRATION] of [EXTRA OPTION] menu and then press the 
[ENTER] button.
 
3. Select the [OK], and press the [ENTER] button to start the calibration.
    Approximately 10 seconds later, if "COMPLETE" is displayed, calibration is complete. Press the [MENU] button to finish.
4. Turn off the main power, turn on the power again, and check that it operates properly.
SUB MENU
ENTER
EXTRA OPTION
DYNAMIC GAMMA MODE
3DCMS
SHUTTER KEEP
ON
ON
OFF
0SEC.
SELF CHECK
POWER OFF MESSAGE
ERROR OSD
ELECTRICAL CONVERGENCE
MECHANICAL CONVERGENCE
MODEL
INDICATOR SETTING
LIGHT ADJUST
COMMAND CONTROL TIMEOUT
PHOTO SENSOR CALIBRATION
MENU SELECT
PHOTO SENSOR CALIBRATION
OK
CANCEL
EXECUTE
CHANGE
ENTER
PHOTO SENSOR CALIBRATION
PROGRESS
PHOTO SENSOR CALIBRATION
COMPLETE
EXIT
MENU
1. 8. Date and time setup
f
 Set the time zone, date, and time of the built-in clock of the projector.
1. Select the [DATE AND TIME] of [PROJECTOR SETUP] menu and press the [ENTER] button.
2. Press [ a ][ s ] button to select [ADJUST CLOCK] and press the [ENTER] button.
3. Press [ a ][ s ] button to select an item, and press [ q ][ w ] button to set the local date and time.
4. Press [ a ][ s ] button to select [APPLY], then press the [ENTER] button to complete the date and time setting.
 • Refer to the operating instructions for the detailed procedures.
PROJECTOR SETUP
1/2
PROJECTOR ID
PROJECTION METHOD
NORMAL
100.0%
OFF
NORMAL
DISABLE
ALL
LAST MEMORY
DISABLE
LAST USED
LENS
OPERATION SETTING
LIGHT OUTPUT
BRIGHTNESS CONTROL
NO SIGNAL SHUT-OFF
STANDBY MODE
NO SIGNAL LIGHTS-OUT
INITIAL STARTUP
STARTUP INPUT SELECT
DATE AND TIME
MENU SELECT
SUB MENU
ENTER
DATE AND TIME
TIME ZONE
ADJUST CLOCK
12:00:00
+09:00
2018/01/01
LOCAL DATE
LOCAL TIME
MENU SELECT
SUB MENU
ENTER
Page of 127
Display

Click on the first or last page to see other PT-RQ22KEJ (serv.man3) service manuals if exist.