PT-RQ13K — Panasonic Projector Service Manual (repair manual). Page 7

View Panasonic PT-RQ13K Service Manual online

7
PREFACE
< RQ13K >
2. Specifications
2.1 Specifications
Power supply
100 V - 240 V 
~  (100 V - 240 V alternating current), 50 Hz/60 Hz
Power consumption
1 270 W (12.0 A - 6.0 A)
When [STANDBY MODE] is set to [ECO]: 0.3 W
When [STANDBY MODE] is set to [NORMAL]: 4 W
DLP chip
Size
22.9 mm (0.90") (aspect ratio 16:10)
Display system
DLP chip x 3, DLP projection system
Number of pixels 4 096 000 pixels (2 560 x 1 600 dots)
Lens
Optional
Light source
Laser, 2-bank type
Light output
*1
10 000 lm (ANSI)
Contrast ratio
*1
20 000:1 (when [DYNAMIC CONTRAST] is set as [3])
Projected image size
1.78 m (70") to 25.40 m (1 000")
*2
Image aspect ratio
16:10
Projection method
[FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
Power cord length
3.0 m (118-1/8")
Outer case
Molded plastic
Dimensions
Width
578 mm (22-3/4")
Height
270 mm (10-5/8") (excluding the feet)
Depth
725 mm (28-17/32") (excluding the protrusion)
Weight
Approx. 49.0 k] (108.0 lbs.)
*3
Noise level
*1
46 dB
Operating 
environment
Operating 
environment 
temperature
0 °C (32 °F) to 45 °C (113 °F)
*4 *5
Operating 
environment 
humidity
10 % to 80 % (no condensation)
Remote 
control
Power supply
DC 3 V (AA/R6/LR6 battery x 2)
Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight
150 ] (5.3 ozs.) (including batteries)
Dimensions
Width: 47.5 mm (1-7/8"), Height: 181.5 mm (7-5/32"), Depth: 27.5 mm (1-3/32")
*1  Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*2  When the Zoom Lens (Model No.: ET-D75LE8) is used, the projected image size for the maximum projection distance will be 1.78 m (70") to 
15.24 m (600"). When the Fixed-focus Lens (Model No.: ET-D75LE90) is used, the projected image size for the maximum projection distance will be 
3.05 m (120") to 15.24 m (600").
*3  Average value. Weight varies for each product.
*4  The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) if the projector is used at an altitude between 1 400 m 
(4 593') and 4 200 m (13 780') above sea level. When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is 
set to [ECO], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3], the operating environment temperature should be between 0 °C (32 °F) and 40 °C 
(104 °F), regardless of the altitude. When the Smoke Cut Filter is used, the operating environment temperature should be between 0 °C (32 °F) and 
35 °C (95 °F).
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [ECO], [LONG LIFE1], [LONG LIFE2], or 
[LONG LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level. When the Smoke Cut Filter is used, the 
projector cannot be used at an altitude of 1 400 m (4 593') or higher above sea level.
*5  When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [NORMAL], and the operating environment 
temperature exceeds the following value, the light output may be reduced to protect the projector.
 
f
When using the projector at an altitude lower than 2 700 m (8 858') above sea level: 35 °C (95 °F)
 
f
When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [ECO], [LONG LIFE1], [LONG LIFE2], or 
[LONG LIFE3], and the operating environment temperature exceeds 35 °C (95 °F), the light output may be reduced to protect the projector.
Note
 
f
The light output will decrease as much as the power supply voltage is decreased. It is recommended to use with AC 200 V or higher to 
prioritize luminance.
Page of 127
Display

Click on the first or last page to see other PT-RQ13K service manuals if exist.