DOWNLOAD Panasonic PT-RQ13K Service Manual ↓ Size: 66.72 MB | Pages: 127 in PDF or view online for FREE

Model
PT-RQ13K
Pages
127
Size
66.72 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / 3-CHIP DLP BASED PROJECTOR
File
pt-rq13k.pdf
Date

Panasonic PT-RQ13K Service Manual ▷ View online

INF-4
SECTION 1 SERVICE INFORMATION
< RQ13K >
1.3 Connecting terminals
1
2
3
4
5
8
9
6
7
1  <REMOTE 1 IN> terminal/<REMOTE 1 OUT> terminal
These are terminals to connect the remote control for serial 
control in a multiple projector environment.
2  <REMOTE 2 IN> terminal
This is a terminal to remotely control the projector using the 
external control circuit.
3  <SERIAL IN> terminal
This is the RS-232C compatible terminal to externally control 
the projector by connecting a computer.
4  <SERIAL OUT> terminal
This is a terminal to output the signal connected to the <SERIAL 
IN> terminal.
5  <FRAME SYNC 1 IN/OUT> terminal/<FRAME SYNC 2 OUT> 
terminal
These are terminals to input and output the control signal 
to synchronize the projected images in a multiple projector 
environment.
The projected images of second and subsequent projectors can 
projected simultaneously.
6  Slots (<SLOT 1>, <SLOT 2>)
Interface Board internally.
7  Slot cover
8  <DIGITAL LINK/LAN> terminal
This is the LAN terminal to connect to the network. This is also 
used when connecting a video signal transmission device via 
the LAN terminal.
9  <SDI IN 1> terminal/<SDI IN 2> terminal/<SDI IN 3> 
terminal/<SDI IN 4> terminal
These are terminals to input SDI signals.
Attention
 
f
When a LAN cable is directly connected to the projector, the network connection must be made indoors.
INF-5
SECTION 1 SERVICE INFORMATION
< RQ13K >
Names and functions of the Interface Board (optional)
There are four SDI input terminals and one DIGITAL LINK input terminal equipped on this projector as the 
standard video input terminals. The input for HDMI, DVI-D, and SDI can be added by installing the optional 
Interface Board in the slot.
The terminal name of the optional Interface Board is described with different terminal name in this document when 
it is installed in <SLOT 1> and when it is installed in <SLOT 2>. Refer to following information for details.
 
r
Interface Board for HDMI 2 input (Model No.: ET-MDNHM10)
This board supports the HDMI signal.
1
3
3
2
1  <HDMI IN 1> terminal (when installed in <SLOT 1>), <HDMI 
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input the HDMI signal.
2  <HDMI IN 2> terminal (when installed in <SLOT 1>), <HDMI 
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input the HDMI signal.
3  Handle
 
r
Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10)
This board supports the DVI-D signal.
1
3
3
2
1  <DVI-D IN 1> terminal (when installed in <SLOT 1>), <DVI-D 
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input the DVI-D signal.
2  <DVI-D IN 2> terminal (when installed in <SLOT 1>), <DVI-D 
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input the DVI-D signal.
3  Handle
 
r
3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G)
This board supports the SD-SDI signal, HD-SDI signal, and 3G-SDI signal.
1
2
3
4
5
1  <3G-SDI 2 OUT> terminal (when installed in <SLOT 1>), 
<3G-SDI 4 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input 
to the <3G-SDI 2 IN> terminal/<3G-SDI 4 IN> terminal of this 
board.
2  <3G-SDI 2 IN> terminal (when installed in <SLOT 1>), 
<3G-SDI 4 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input the SDI signal.
3  <3G-SDI 1 OUT> terminal (when installed in <SLOT 1>), 
<3G-SDI 3 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input 
to the <3G-SDI 1 IN> terminal/<3G-SDI 3 IN> terminal of this 
board.
4  <3G-SDI 1 IN> terminal (when installed in <SLOT 1>), 
<3G-SDI 3 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input the SDI signal.
5  Handle
Note
 
f
This projector does not support audio output because it is not equipped with audio function. However, when SDI signal with audio is input to 
the <3G-SDI 1 IN>/<3G-SDI 2 IN>/<3G-SDI 3 IN>/<3G-SDI 4 IN> terminal, a signal with audio is output from the <3G-SDI 1 OUT>/<3G-SDI 
2 OUT>/<3G-SDI 3 OUT>/<3G-SDI 4 OUT> terminal.
INF-6
SECTION 1 SERVICE INFORMATION
< RQ13K >
1.4 Remote controls
1
2
6
4
7
5
8
9
10
3
13
12
11
20
14
15
16
23
17
18
19
21
22
Front
Top
Bottom
A strap can be attached 
depending on the usage.
1  Remote control indicator
Blinks if any button in the remote control is pressed.
2  Power on <b> button
Sets the projector to projection mode when the <MAIN 
POWER> switch on the projector is set to <ON> and the power 
is turned off (standby mode).
3  Power standby <v> button
Sets the projector to the state where the projector is turned 
off (standby mode) when the <MAIN POWER> switch on the 
projector is set to <ON> and in projection mode.
4  <MENU> button/<ENTER> button/asqw buttons
Used to navigate through the menu screen. 
5  <ON SCREEN> button
Switches the on-screen display function on (display) or off 
(hide).
6  <AUTO SETUP> button
Automatically adjusts the image display position while projecting 
the image.
[PROGRESS] is displayed while in automatic adjustment. 
7  <ASPECT> button
Switches the aspect ratio of the image. 
8  Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple 
projector environment.
9  <STATUS> button
Displays the projector information.
10  <LIGHT> button
Pressing this button lights up the remote control buttons. The 
lights will go off when the remote control operation goes idle for 
10 seconds.
11  <INPUT MENU> button
Displays the input selection screen. 
12  Input selection buttons (<DIGITAL LINK>, <DVI-D>, <HDMI>, 
<SLOT 1>, <SLOT 2>, <SDI>)
Switches the input signal to project.
<DVI-D> button, <HDMI> button, <SLOT 1> button, and 
<SLOT 2> button can be used when the optional Interface 
Board equipped with corresponding input is installed in the slot 
on the projector.
Following buttons are not used with this projector.
<RGB 1> button, <RGB 2> button, <VIDEO> button, <S-VIDEO 
Y/C> button, <DISPLAY PORT> button
13  <SHUTTER> button
Used to temporarily turn off the image.
14  <TEST PATTERN> button
Displays the test pattern. 
15  Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)
Adjusts the projection lens. 
16  <FUNCTION> button
Assigns a frequently used operation as a shortcut button. 
17  <DEFAULT> button
Resets the content of the sub-menu to the factory default. 
18  <ID SET> button
Sets the ID number of the remote control in a multiple projector 
environment.
19  <ID ALL> button
Used to simultaneously control all the projectors with a 
single remote control in a multiple projector environment. 
20  <LOCK> button
Used to prevent unintended operation by careless pressing of 
the buttons and prevent draining the remote control batteries.
Operation of each button on the remote control is disabled by 
sliding the <LOCK> button toward the arrow.
21  Remote control signal transmitter
22  Remote control wired terminal
This is a terminal used to connect to the projector via a cable 
when the remote control is used as a wired remote control. 
23  Strap hole
INF-7
SECTION 1 SERVICE INFORMATION
< RQ13K >
Attention
 
f
Do not drop the remote control.
 
f
Avoid contact with liquids or moisture.
 
f
Do not attempt to modify or disassemble the remote control.
 
f
Do not swing the remote control holding onto the strap when a strap is attached.
 
f
Observe the following instructions that are indicated on the caution label at the back of the remote control:
 
g
Do not use old battery with new one.
 
g
 
g
Be sure the batteries are inserted properly.
1.Do not use old battery with new one.
2.Do not use batteries other than the
   type specified.
3.Be sure the batteries are inserted properly.
Made in China
N2QAYB001052
Caution label at the back of the remote control
Note
 
f
When operating the remote control by directly pointing the remote control signal receiver of the projector, operate the remote control at 
a distance approx. 30 m (98'5") or shorter from the remote control signal receiver. The remote control can control at angles of up to ±15° 
vertically and ±30° horizontally, but the effective control range may be reduced.
 
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
 
f
 
f
. Use 
it in a place distant from the light source.
 
f
The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
Page of 127
Display

Click on the first or last page to see other PT-RQ13K service manuals if exist.