Panasonic PT-RQ13K (serv.man2) Service Manual ▷ View online
10
PREFACE
< RQ13K >
2.4. Dimensions
DIGITAL LINK input
f
Moving image signal resolution: 480i
*2
/576i
*2
to 4 096 x 2 160
Still image signal resolution: 640 x 400 to 2 560 x 1 600 (non-interlace)
f
Dot clock frequency: 25 MHz to 297 MHz
HDMI input
*3
f
Moving image signal resolution: 480i
*2
/576i
*2
to 4 096 x 2 160
Still image signal resolution: 640 x 400 to 2 560 x 1 600 (non-interlace)
f
Dot clock frequency: 25 MHz to 594 MHz
DVI-D input
*4
f
Moving image signal resolution: 480i
*2
/576i
*2
to 2 048 x 1 080
Still image signal resolution: 640 x 400 to 1 920 x 1 200 (non-interlace)
f
Dot clock frequency: 25 MHz to 162 MHz
*1 In addition to the standard SDI input, this supports the input from the optional 3G-SDI Terminal Board with Audio (Model No. TY-TBN03G) installed
in the slot.
Optional 3G-SDI Terminal Board with Audio (Model No. TY-TBN03G) is required to be installed in both of <SLOT 1> and <SLOT 2> when
performing quad link using the input of the optional 3G-SDI Terminal Board with Audio (Model No. TY-TBN03G) installed in the slot.
*2 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
*3 This is supported when the optional Interface Board for HDMI 2 input (Model No. ET-MDNHM10) is installed in the slot.
*4 This is supported when the optional Interface Board for DVI-D 2 input (Model No. ET-MDNDV10) is installed in the slot.
Note
f
The model numbers of accessories and optional accessories are subject to change without prior notice.
Unit: mm
242 (9-17/32")
289 (11-3/8")
578 (22-3/4")
637 (25-3/32")
484 (19-1/16")
53.5 (2-3/32")
142 (5-1
9/32")
270 (10-5/8")
15 (19/32")
725 (28-1
7/32")
* Actual dimensions may differ depending on the product.
INF-1
CONTENTS
Service Information
Model No.
PT-RQ13K
SECTION 1 SERVICE INFORMATION
1. The name of each part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-2
1.1 Projector body
1.2 Control panel
1.3 Connecting terminals
1.4 Remote controls
1.2 Control panel
1.3 Connecting terminals
1.4 Remote controls
2. Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-8
3. Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-12
3. Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-12
3. 1. Setting to Service Mode
3. 2. Resetting to User Mode
3. 3. Functions of Service Mode
3. 2. Resetting to User Mode
3. 3. Functions of Service Mode
4. Notes on service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-21
4. 1. Before service operation
4. 2. Service
4. 3. Replacement of consumable parts
4. 4. Installing the Interface Board (optional)
4. 5. Security password
4. 2. Service
4. 3. Replacement of consumable parts
4. 4. Installing the Interface Board (optional)
4. 5. Security password
5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-28
5. 1. Power/Light source/temperature/fIlter indicators
5. 2. Shutdown system
5. 3. System log data acquisition method
5. 4. Troubleshooting
5. 2. Shutdown system
5. 3. System log data acquisition method
5. 4. Troubleshooting
INF-2
SECTION 1 SERVICE INFORMATION
< RQ13K >
1. The name of each part
1.1 Projector body
1 2 3 4 5 6
7
7
9
8
8
8
12
16 17
13
14
15
10
Front
Side
Rear
11
Projection direction
Bottom
1 Remote control signal receiver (front)
2 Power indicator <ON (G)/STANDBY (R)>
2 Power indicator <ON (G)/STANDBY (R)>
Indicates the status of the power.
3 Light source indicator <LIGHT1>
Indicates the status of light source 1.
4 Light source indicator <LIGHT2>
Indicates the status of light source 2.
5 Temperature indicator <TEMP>
Indicates the internal temperature status.
6 Filter indicator <FILTER>
7 Adjustable feet
Adjusts the projection angle.
8 Air intake port
9 Remote control signal receiver (rear)
9 Remote control signal receiver (rear)
10 Air exhaust port
11 Burglar hook port
11 Burglar hook port
Attaches a burglar prevention cable, etc.
12
13 Control panel
14 Connecting terminals
15 Security slot
14 Connecting terminals
15 Security slot
This security slot is compatible with the Kensington security
cables.
16 <AC IN> terminal
Connect the supplied power cord.
17 <MAIN POWER> switch
Turns on/off the main power.
Attention
f
Do not block the ventilation ports (intake and exhaust) of the projector.
INF-3
SECTION 1 SERVICE INFORMATION
< RQ13K >
1.2 Control panel
7
8
8
9
10
11
10
11
12
1
2
3
4
5
6
1 Power on <b> button
Sets the projector to projection mode when the <MAIN
POWER> switch on the projector is set to <ON> and the power
is turned off (standby mode).
2 Power standby <v> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
3 Input selection buttons (<SDI 1/2>, <SDI 3/4>, <DIGITAL
LINK>, <SLOT 1>, <SLOT 2>)
Switches the input signal to project.
<SLOT 1> button and <SLOT 2> button can be used when the
optional Interface Board is installed in the slot on the projector.
4 Input selection terminal indicator
Indicator that shows the selected input terminal. This indicator
lights up when a video signal is being input to the selected
terminal, and blinks when there is no video signal being input.
5 <INPUT MENU> button
Displays the input selection screen.
The indicator of the button is lit while this button is pressed.
6 <AUTO SETUP> button
Automatically adjusts the image display position while the
image is projected. [PROGRESS] is displayed while in
automatic adjustment.
7 <MENU> button
Displays or hides the main menu.
Returns to the previous menu when a sub-menu is displayed.
If you press the <MENU> button on the control panel for at least
three seconds while the on-screen display is off (hidden), the
on-screen display is turned on.
8 <LENS> button
Adjusts the focus, zoom, and shift (position) of the lens.
9 <ENTER> button
Determines and executes an item in the menu screen.
10 <SHUTTER> button
Used to temporarily turn off the image.
11 asqw buttons
Used to select items in the menu screen, change settings, and
adjust levels.
Also used to enter a password in [SECURITY] or enter
characters.
12 Self-diagnosis display
Automatically displays the value of the input supply voltage, or
details of errors or warnings when they occur.
Click on the first or last page to see other PT-RQ13K (serv.man2) service manuals if exist.