DOWNLOAD Panasonic PT-RCQ10 / PT-RCQ80 (serv.man3) Service Manual ↓ Size: 35.62 MB | Pages: 116 in PDF or view online for FREE

Model
PT-RCQ10 PT-RCQ80 (serv.man3)
Pages
116
Size
35.62 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / 1-CHIP DLP BASED PROJECTOR
File
pt-rcq10-pt-rcq80-sm3.pdf
Date

Panasonic PT-RCQ10 / PT-RCQ80 (serv.man3) Service Manual ▷ View online

ADJ-13
SECTION 3 ADJUSTMENTS
< RCQ10 / RCQ80 >
(2) [SLOPE] adjustment
  • If the three lines are blurred even after adjusting the focus, adjust so that there is no bleeding.
(3) [PHASE 60Hz] / [PHASE 50Hz] adjustment
  •  Normally no adjustment is required. 
If there are jaggies on the slanted lines or curved ilnes of the image, adjust it so that it is not noticeable.
NG image
OK image
ADJ-14
SECTION 3 ADJUSTMENTS
< RCQ10 / RCQ80 >
2. Firmware update procedure
f
  Firmware updating can be done via the LAN terminal or the SERIAL terminal. 
   DIGITAL LINK firmware can be done via the serial terminal only.
f
 It is recommended to use the LAN terminal for updating the firmware.(updating speed is faster than serial terminal)
2. 1. Equipment to be used
1. Computer : Use it for firmware transferring
2. Communication cable : 
    
3. Service Software : [MainSubNtUpdateTool.exe ]      Download from the projector service website.
4. Firmware software : Download the firmware file from the projector service website to the PC.
2. 2. Connection Preparations
1. Check the settings of the projector.
 
LAN terminal connection
  1) Set [NETWORK CONTROL] → [TYPE SELECT] in the [NETWORK] menu to [LAN].
  2) Check the projector IP address in [NETWORK STATUS] of the [NETWORK] me and take a note.
  3) Set the IP address of computer to approximate (same network group) value of the projector IP address.
 
  SERIAL terminal connection
  1)  The [INPUT SELECT] of sub menu [RS-232C] in [PROJECTOR SETUP] must be set according to the connection meth-
od.
  2) Enter the service mode, set [RS-232C] → [EMULATE] in the [PROJECTOR SETUP] menu to [OFF].
  3) Check the RS-232C settings (ID, Baudrate and Parity) and take a note.
  
• If you have changed the each menu settings, please return settings to the original (customers) after work.
2. Connect the projector and the PC by using a communication cable.
 
LAN terminal connection example
SERIAL terminal connection example
Projector SERIAL IN
Communication cable (straight)
Computer
D-Sub 9P
(male)
D-Sub 9p (female)
LAN cable (straight)
LAN cable (straight)
Projector LAN
Computer
Hub
2. 3. Update procedure
1. Switch the projector to "Normal-Standby" mode.
2. Start up service software [MainSubNetUpdateTool.exe] with a computer.
LAN terminal connection
LAN cable. (When connecting directly, use a cross cable)
SERIAL terminal connection D-sub 9pin (male/female RS-232C straight)
ADJ-15
SECTION 3 ADJUSTMENTS
< RCQ10 / RCQ80 >
4.  Select connection (LAN or Serial) method and enter the setting information of the projector.
 
LAN terminal connection
  • Select [LAN] menu and set up the IP address of the projector.
    
 
  SERIAL terminal connection
  • Select [SERIAL] menu and set up the Serial Port, Baudrate and Parity of the PC.
 
•  Setting of Username, Password, Command Port is unnecessary.
3. Select the model number in the following way and click the [OK] button.
  1) Model selection by keyword search
    • Select "Manual Select" and enter all or part of model name in the "Keyword" frame.
  2)  Model selection by network search
    •  Select "Network Selection" and select the IP address of the computer and click the [Search] button to display a list of 
the connected projectors in the network.
Items
Default
SERIAL
Port
Baud Rate
9600bps
Parity
None
LAN
IP Address
192.168.0.8
Username
dispadmin
Password
@Panasonic
Command Port
1024
ADJ-16
SECTION 3 ADJUSTMENTS
< RCQ10 / RCQ80 >
5. When the connection setup is completed, click the [Connection Check] button and check the connection with projector.
    • If "Check : OK" is displayed, click the [OK] button and proceed to the next step.
    • If "Check : NG" is displayed, check the setting in step 4.
6. Click [load] button which you want to firmware update in the "Select Microcomputer's firmware file" frame.
    • Click the [NEXT] / [PREVIOUS] button to switch "Select Microcomputer's firmware file" frames.
    • When updating the optional interface board, select "SLOT1".
• LAN connection
• SERIAL connection
Page of 116
Display

Click on the first or last page to see other PT-RCQ10 / PT-RCQ80 (serv.man3) service manuals if exist.