Panasonic PT-MZ16K / PT-MZ13K / PT-MZ10K (serv.man2) Service Manual ▷ View online
6
PREFACE
<MZ16K/MZ13K/MZ10K>
1. Safety Precautions
1.1. General Guidelines
- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this projector.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed
and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated or damaged
by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C combi-
nations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.
1.2. Leakage Current Check
1. Prepare the measuring circuit as shown in Fig.1.
Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75mA or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer
because of a possibility of an electric shock.
M1
M2
Rs
Cs
Rb
10KΩ ±0.1%
0.022µF
±1.0%
Vb
(V) V
Rs: 1500 Ω±0.1%
Cs: 0.22 µF±1.0%
Rb: 500 Ω±0.1%
to T1
or T2
in FIg.2
Weighted leakage current=Vb / 500 (A)
Fig. 1
Isolation transformer
T1
T2
connection
to power outlet
M1
M2
Fig.2
Projector
Measuring
Circuit (Fig.1)
Performance
Voltmeter
(rms reading)
Accurancy:
≤ 2%
Input resistance:
≥ 1 MΩ
Input capacitance: ≤ 200 pF
Frequency range: 15 Hz to 1 MHz
Table. 1
7
PREFACE
<MZ16K/MZ13K/MZ10K>
2. Specifications
Chapter 7 Appendix — Specifications
234 - ENGLISH
Specifications
The specifications of the projector are as follows.
Power supply
100 V - 240 V ~ (100 V - 240 V alternating current), 50 Hz/60 Hz
Power consumption
PT-MZ16K
1 050 W (11.0 A - 4.5 A)
PT-MZ13K
800 W (8.3 A - 3.4 A)
PT-MZ10K
640 W (6.5 A - 2.7 A)
Power consumption (during
standby)
Approx. 0.5 W
When [STANDBY MODE] is set to [ECO]
Approx. 8 W
When [STANDBY MODE] is set to [NORMAL]
Approx. 150 W
When [QUICK STARTUP] is set to [ON] and the power is supplied from the <DC
OUT> terminal
LCD panel
Size
25.4 mm (1.0") (aspect ratio 16:10)
Display system
Translucent screen LCD panel 3 panels, 3 primary colors system
Drive system
Active matrix
Number of pixels 2 304 000 pixels (1 920 x 1 200 dots) x 3
Lens
Optional
Light source
Laser diode
Light output
PT-MZ16K
16 000 lm
*1
(when [OPERATING MODE] in [OPERATION SETTING] is set to [NORMAL])
PT-MZ13K
13 000 lm
*1
(when [OPERATING MODE] in [OPERATION SETTING] is set to [NORMAL])
PT-MZ10K
10 000 lm
*1
(when [OPERATING MODE] in [OPERATION SETTING] is set to [NORMAL])
Center to corner zone ratio
*1
90 %
Contrast ratio
*1
3 000 000:1 (when [DYNAMIC CONTRAST] is set to [3])
Projected image size
2.03 m (80") to 12.70 m (500")
Image aspect ratio
16:10
Projection method
[FRONT]/[FLOOR], [FRONT]/[CEILING], [REAR]/[FLOOR], [REAR]/[CEILING]
Power cord length
3.0 m (118-1/8")
Outer case
Molded plastic
Outer color
Black model
Black
White model
White
Dimensions
Width
650 mm (25-19/32")
Height
185 mm (7-9/32") (with the feet at shortest position)
Depth
440 mm (17-5/16") (excluding the optional lens)
Weight
Approx. 22.3 k] (49.1 lbs.)
*2
(excluding the optional lens)
Noise level
*1
PT-MZ16K
38 dB
(when [OPERATING MODE] in [OPERATION SETTING] is set to [NORMAL])
PT-MZ13K,
PT-MZ10K
35 dB
(when [OPERATING MODE] in [OPERATION SETTING] is set to [NORMAL])
Laser
Classification
Laser Class
USA and Canada: Class 3R (IEC 60825-1:2007)
Other countries or regions: Class 1 (IEC/EN 60825-1:2014)
Other countries or regions: Class 1 (IEC/EN 60825-1:2014)
Risk Group
PT-MZ16K
ET-EMW200, ET-EMW300,
ET-EMW400, ET-EMW500,
ET-EMS600
Risk group 2 (IEC 62471-5:2015)
ET-EMT700
*3
Risk group 2 or Risk group 3 (IEC
62471-5:2015)
ET-EMT800
Risk group 3 (IEC 62471-5:2015)
PT-MZ13K
ET-EMW200, ET-EMW300,
ET-EMW400, ET-EMW500,
ET-EMS600
Risk group 2 (IEC 62471-5:2015)
ET-EMT700
*4
Risk group 2 or Risk group 3 (IEC
62471-5:2015)
ET-EMT800
Risk group 3 (IEC 62471-5:2015)
PT-MZ10K
ET-EMW200, ET-EMW300,
ET-EMW400, ET-EMW500,
ET-EMS600, ET-EMT700
Risk group 2 (IEC 62471-5:2015)
ET-EMT800
*5
Risk group 2 or Risk group 3 (IEC
62471-5:2015)
8
PREFACE
<MZ16K/MZ13K/MZ10K>
Chapter 7 Appendix — Specifications
ENGLISH - 235
Operating
environment
Operating
environment
temperature
0 °C (32 °F) to 45 °C (113 °F)
*6
Operating
environment
humidity
10 % to 80 % (no condensation)
Remote
control
Power supply
DC 3 V (AAA/R03/LR03 battery x 2)
Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight
Weight
102 ] (3.6 ozs.) (including batteries)
Dimensions
Width: 48 mm (1-7/8"), Height: 145 mm (5-23/32"), Depth: 27 mm (1-1/16")
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2012 international standards.
*2 Average value. Weight varies for each product.
*3 When the throw ratio is 2.9:1 or less: Risk group 2
When the throw ratio exceeds 2.9:1: Risk group 3
*4 When the throw ratio is 3.4:1 or less: Risk group 2
When the throw ratio exceeds 3.4:1: Risk group 3
*5 When the throw ratio is 4.6:1 or less: Risk group 2
When the throw ratio exceeds 4.6:1: Risk group 3
*6 When using the projector at an altitude lower than 2 700 m (8 858') above sea level, and the operating environment temperature becomes 35 °C
(95 °F) or higher, the light output may be reduced to protect the projector.
Note
f
The model numbers of accessories and optional accessories are subject to change without prior notice.
r
Connecting terminal
<RGB IN> terminal
1 set, high-density D-Sub 15 p (female)
RGB signal
RGB signal
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD
SYNC/HD
TTL high impedance, automatic positive/negative
polarity compatible
VD
TTL high impedance, automatic positive/negative
polarity compatible
YP
B
P
R
signal
Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
<DVI-D IN> terminal
1 set, DVI-D 24 p, single link, DVI 1.0 compliant, HDCP compatible
<HDMI IN> terminal
1 set, HDMI 19 p, HDCP 2.2 compatible, Deep Color compatible
<SDI IN> terminal
1 set (BNC)
HD-SDI signal
HD-SDI signal
SMPTE ST 292 compliant
3G-SDI signal
SMPTE ST 424, 425-2 compliant
<SERIAL/MULTI PROJECTOR
SYNC IN>/ <SERIAL/MULTI
PROJECTOR SYNC OUT>
terminal
D-Sub 9 p, 1 set each, RS-232C compliant, for computer control
<REMOTE 1 IN> terminal
1 set, D-Sub 9 p, for contact control
<REMOTE 2 IN>/ <REMOTE 2
OUT> terminal
M3 stereo mini jack, 1 set each, for remote control (wired)/for projector connection control
<DIGITAL LINK> terminal
1 set, RJ-45, for network and DIGITAL LINK connections (HDBaseT
TM
compliant), PJLink (class 2)
compatible, 100Base-TX, Art-Net compatible, HDCP 2.2 compatible, Deep Color compatible
<LAN> terminal
1 set, RJ-45, for network connection, PJLink (class 2) compatible, 10Base-T/100Base-TX, Art-Net
compatible
<DC OUT> terminal
USB connector (type A) x 1, for power supply (DC 5 V, maximum 2 A)
9
PREFACE
<MZ16K/MZ13K/MZ10K>
Chapter 7 Appendix — Specifications
236 - ENGLISH
r
Compatible signal
For details of the types of video signals that can be used with the projector, refer to “List of compatible
signals”.
RGB signal input
f
Resolution: 640 x 480 to 1 920 x 1 200
f
Dot clock frequency: 162 MHz or less
f
PIAS (Panasonic Intelligent Auto Scanning) system
YC
B
C
R
/YP
B
P
R
signal input
f
Resolution: 480p/576p to 1 920 x 1 080
f
Dot clock frequency: 148.5 MHz or less
f
The HD/SYNC and VD terminals do not support 3 value SYNC.
DVI-D signal input
f
Moving image signal resolution: 480p/576p to 1 920 x 1 080
Still image signal resolution: 640 x 480 to 1 920 x 1 200 (non-interlace)
Still image signal resolution: 640 x 480 to 1 920 x 1 200 (non-interlace)
f
Dot clock frequency: 25 MHz to 162 MHz
HDMI signal input
f
Moving image signal resolution: 480p/576p to 4 096 x 2 160
Still image signal resolution: 640 x 480 to 1 920 x 1 200 (non-interlace)
Still image signal resolution: 640 x 480 to 1 920 x 1 200 (non-interlace)
f
Dot clock frequency: 25 MHz to 594 MHz
DIGITAL LINK signal input
f
Moving image signal resolution: 480p/576p to 4 096 x 2 160
Still image signal resolution: 640 x 480 to 1 920 x 1 200 (non-interlace)
Still image signal resolution: 640 x 480 to 1 920 x 1 200 (non-interlace)
f
Dot clock frequency: 25 MHz to 297 MHz
SDI signal input
HD-SDI signal
3G-SDI signal
HD-SDI signal
3G-SDI signal
Click on the first or last page to see other PT-MZ16K / PT-MZ13K / PT-MZ10K (serv.man2) service manuals if exist.