DOWNLOAD Panasonic PT-MZ16K / PT-MZ13K / PT-MZ10K (serv.man2) Service Manual ↓ Size: 18.05 MB | Pages: 116 in PDF or view online for FREE

ADJ-9

Before taking this setting, confirm the type of optical block (L-Type or 

R-Type) according to the item "Optical block type check" in the sec-

tion 1 "Service Information".

1.  Enter the service mode (EXTRA OPTION) and select [PANEL 

TYPE SETTING].

2.  Change the panel type to [L] or [R] with [

t

] [

u

] buttons to match 

the optical block type which is installed on the projector.

  L: L-Type

  R: R-Type

1.  Enter the service mode (EXTRA OPTION) and select [FLICKER 

ADJUST] and press [ENTER] button to enter the flicker adjustment 

mode.

2.  The whole red raster pattern will displayed on the screen when 

entering the adjustment mode.

3. Adjust the flicker to be minimum with [

t

] [

u

] buttons.

4.  Change another adjustment pattern with [

p

] [

q

] buttons and 

repeat the step 3 above.

  Projector provide 3 adjustment patterns "Red", "Green" and "Blue".

5.  After finishing the adjustment, press [MENU] button to exit the 

adjustment mode.

1.  Enter the service mode (EXTRA OPTION) and select [MODEL] 

and press [ENTER] button to enter the model setting mode.

2.  Select the model of the projector with [

p

] [

q

] buttons and press 

[ENTER] button.

3.  After finishing the setting, press [MENU] button to exit the setting 

mode.

4. Turn the main switch and on again, then the setting will applied.

5.  Check the model information to display the [STATUS] of [PROJEC-

TOR SETUP] menu.

● In case of the Optical block replaced: 
  Confirm that the type of optical block and setting are matched. 
● In case of A-PCB replaced: 
   After transferring the standard or original gamma/uniformity data, 

confirm that the type of optical block and setting are matched.

EXTRA OPTION

1/2

DYNAMIC GAMMA MODE
3DCMS

SHUTTER KEEP

ON
ON

OFF

L

---

SELF CHECK
FLICKER ADJUST
POWER OFF MESSAGE
ERROR OSD
MODEL
LIGHT RUNTIME RESET

PANEL TYPE SETTING

RGB PIXEL ADJUST
GHOST FB CALIBRATION
CLOG SENSOR CALIBRATION

MENU SELECT

CHANGE

EXTRA OPTION

1/2

DYNAMIC GAMMA MODE
3DCMS

SHUTTER KEEP

ON
ON

OFF

L

---

SELF CHECK

FLICKER ADJUST

POWER OFF MESSAGE
ERROR OSD
MODEL
LIGHT RUNTIME RESET
PANEL TYPE SETTING
RGB PIXEL ADJUST
GHOST FB CALIBRATION
CLOG SENSOR CALIBRATION

MENU SELECT

CHANGE

EXTRA OPTION

1/2

DYNAMIC GAMMA MODE
3DCMS

SHUTTER KEEP

ON
ON

OFF

L

PT-MZ16K

SELF CHECK
FLICKER ADJUST
POWER OFF MESSAGE
ERROR OSD

MODEL

LIGHT RUNTIME RESET
PANEL TYPE SETTING
RGB PIXEL ADJUST
GHOST FB CALIBRATION
CLOG SENSOR CALIBRATION

MENU SELECT

CHANGE

MODEL

 

    WUXGA  :PT-MZ16K

 

  D WUXGA  :PT-MZ16KD

   X 

WUXGA :PT-MZ16KX

 

  E WUXGA  :PT-MZ16KE

 

  J WUXGA  :PT-MZ16KJ

  

C WUXGA :PT-SMZ16KC

 

  X WUXGA  :PT-MZ13KX

 

  E WUXGA  :PT-MZ13KE

 

  J WUXGA  :PT-MZ13KJ

 

  C WUXGA  :PT-SMZ13KC

 

    WUXGA  :PT-MZ13K

 

  D WUXGA  :PT-MZ13KD

MENU SELECT

SET

ENTER

ADJ-10

This ghost feedback (GCFB) function operates to control the ghost 

to be the best position constantly by detecting the aging fluctuation 

of GCFB pulse generated from LCD panels. Projector reads out the 

pulse status at the production and memorizes it as initial value.

*  This calibration should be done when the optical block is replaced. 

When the A-PCB is replaced, the item "1.4. Adjusted data transfer"  

should be done to get its initial value.

1.  Enter the service mode (EXTRA OPTION) and select [GHOST FB 

CALIBRATION].

2. Press [ENTER] button to start the calibration.

3.  When calibration is complete, the message will appear on the 

screen.

4.  Press [MENU] button to exit the adjustment mode.

EXTRA OPTION

1/2

DYNAMIC GAMMA MODE
3DCMS

SHUTTER KEEP

ON
ON

OFF

L

PT-MZ16K

SELF CHECK
FLICKER ADJUST
POWER OFF MESSAGE
ERROR OSD
MODEL
LIGHT RUNTIME RESET
PANEL TYPE SETTING
RGB PIXEL ADJUST

GHOST FB CALIBRATION

CLOG SENSOR CALIBRATION

MENU SELECT

CHANGE

EXTRA OPTION

1/2

DYNAMIC GAMMA MODE
3DCMS

SHUTTER KEEP

ON
ON

OFF

L

PT-MZ16K

SELF CHECK
FLICKER ADJUST
POWER OFF MESSAGE
ERROR OSD
MODEL
LIGHT RUNTIME RESET
PANEL TYPE SETTING
RGB PIXEL ADJUST
GHOST FB CALIBRATION

CLOG SENSOR CALIBRATION

MENU SELECT

CHANGE

GHOST FB CALIBRATION

OK

CLOG SENSOR CALIBRATION

OK

CANCEL

This is to calibrate the clog sensor circuit.

•  This calibration should be done in the condition that the projector is 

completely assembled and place on the floor and the adjuster legs 

are set in the cabinet bottom.

• Replace the air filter with new one before starting calibration.

•  The work should be done at the location where there are no heat 

apparatus and the ventilation opening of the air-conditioner and the 

object to block the exhaust air.

•  This calibration can be done under the intake temperature between 

15℃ to 35℃.

1.  Enter the service mode (EXTRA OPTION) and select [CLOG 

SENSOR CALIBRATION], and press [ENTER] button to enter the 

adjustment mode.

2. Select [OK] and press [ENTER] button to start the calibration.

   During the calibration, the projector displays white raster and the 

progression will be displayed with [0%- 100%].

3.  After apporox. 15 minutes, [CLOG CLIB OK] will display to show 

the calibration completed.

• Do not turn off the projector during the calibration.

ADJ-11

DATE AND TIME

TIME ZONE

ADJUST CLOCK

+09:00

2019/10/25

18:18:24

LOCAL DATE
LOCAL TIME

MENU SELECT

CHANGE

EXTRA OPTION

1/2

DYNAMIC GAMMA MODE
3DCMS

SHUTTER KEEP

ON
ON

OFF

L

PT-MZ16K

SELF CHECK
FLICKER ADJUST
POWER OFF MESSAGE
ERROR OSD
MODEL

LIGHT RUNTIME RESET

PANEL TYPE SETTING
RGB PIXEL ADJUST
GHOST FB CALIBRATION
CLOG SENSOR CALIBRATION

MENU SELECT

CHANGE

LD unit

(TOP)

LD unit

(FRONT)*

LD unit

(BOTTOM)

MODEL

LD unit

TOP

FRONT

BOTTOM

PT-MZ16K

LD1-1

LD1-2

LD2-1

PT-MZ13K

LD1-1

LD2-1

LD1-2

PT-MZ10K

LD1-1

-

LD2-1

• After replaceing the LD unit with new one, the runtime of LD unit should 

be reset with the service menu.

1.  Enter the service mode (EXTRA OPTION) and select [LIGHT RUNTIME 

RESET] and press [ENTER] button.

2. Select LD unit no. to reset and press [ENTER] button

Take care that the LD unit placement and type differ dependong on the models.

* Model PT-MZ10K does not provide the LD unit (FRONT).

3. The conformation window will appear. Select [OK] and press [OK] button. The runtime of the LD unit will be reset.

4. Please check that the runtime has been reset and proper lighting condition will be indicated on the [STATUS] menu

1.  Select THE SUB MENU [DATE AND TIME] of [PROJECTOR SETUP] 

menu.

2. Set the time zone, date, and time of the built-in clock of the projector.

• For further instructions, refer to the operating instructions.

ADJ-12

• Firmware updating can be done via LAN terminal or the serial terminal. (Updating of DIGITAL LINK firmware can be done via  

  the serial terminal only.) 

•  It is recommend to use the LAN terminal for faster updating.

1. Computer : Use it for transmitting the firmware data.

2. Communication cable :

 

Serial terminal connection

D-sub 9 pin (male/female RS-232C straight)

LAN terminal connection

LAN cable. (When connecting directly, use a cross cable)

 

3. Service tool :[MainSubNtUpdatetool.exe] Download from the projector service Web (PASS).

4.  Microprocessor firmware: Please download the file from the projector service homepage to your PC.

1.  Check the settings of the projector.  

     Serial terminal connection

1)  Select the sub menu [RS-232C] of the main menu [PROJECTOR SETUP] and setup [INPUT SELECT] to your connecting 

environment.

2)  Enter the service mode and select sub menu [RS232C] of main menu[PROJECTOR SETUP], and setup [EMULATE] to 

[OFF].

3) Check the RS-232C settings (ID/Baudrate/Parity) and take them note.

    

 

LAN terminal connection

1)   Select the sub menu [NETWORK LINK MODE] of the main menu [NETWORK] and set up [AUTO] or [ETHERNET].

2) Select sub menu [NETWORK STATUS] of main menu [NETWORK] and check the IP address and take a note. 

3) 

3) Setup the IP address of computer's network to the same network group of the projector.

• Setup the projector not to set into the standby mode or shutdown during the updating. 

• If you have changed the each menu settings, please return settings of the original (customers) after work.

2. Connect the projector and the PC by using a communication cable.

Serial terminal connection example

LAN terminal connection example

Projector SERIAL IN

Communication cable (straight)

Computer

D-Sub 9P

(male)

D-Sub 9p (female)

LAN cable (straight)

LAN cable (straight)

Projector LAN

Computer

Hub

1. Set the projector to "Normal-Standby" mode (ON(G)/STANDBY(R) indicator lights in red).

2. Start up service software (MainSubNtUpdateTool.exe) with a computer. The model setting window will appear.