Panasonic PT-MZ16K / PT-MZ13K / PT-MZ10K (serv.man2) Service Manual ▷ View online
ADJ-4
SECTION 3 ADJUSTMENTS
<MZ16K/MZ13K/MZ10K>
1.2. Lens calibration
1. Select the sub menu [LENS CALIBRATION] on the main menu [PRO-
JECTOR SETUP], and then press [ENTER] button.
2. A confirmation window appears. Select [OK] and press [ENTER]
button.
3. Lens will move vertically/horizontally to detect the limit value of the
lens shift, and setup the home position automatically. After that, the
focus/zoom motors will move to detect the limit value automatically.
4. After finishing the calibration, the main manu will be displayed.
1.3. Electrical convergence adjustment
This is a function to correct a convergence by a pixel unit every
R/G/B ingredient.
Each pixel can be shifted in 1 dot and 2 dots maximum from right to
left and up and down.
1. Project cross-hatch pattern, confirm a position gap of R/G/B.
2. Enter the service mode (EXTRA OPTION) and select [RGB
PIXEL ADJUST] and press [ENTER] button to enter the conver-
gence adjustment mode.
3. Select the item of color and direction with [
p
] [
q
] button, and
press [
t
] [
u
] button to correct the convergence.
4. After finishing the adjustment, press [MENU] button to exit the
adjustment mode. The setting value will stored this time.
EXTRA OPTION
1/2
DYNAMIC GAMMA MODE
3DCMS
3DCMS
SHUTTER KEEP
ON
ON
ON
OFF
L
---
SELF CHECK
FLICKER ADJUST
POWER OFF MESSAGE
ERROR OSD
MODEL
LIGHT RUNTIME RESET
PANEL TYPE SETTING
FLICKER ADJUST
POWER OFF MESSAGE
ERROR OSD
MODEL
LIGHT RUNTIME RESET
PANEL TYPE SETTING
RGB PIXEL ADJUST
GHOST FB CALIBRATION
CLOG SENSOR CALIBRATION
CLOG SENSOR CALIBRATION
MENU SELECT
CHANGE
RGB PIXEL ADJUST
RED HSHIFT
GREEN HSHIFT
0
0
0
0
0
0
0
0
0
0
0
BLUE HSHIFT
RED VSHIFT
GREEN VSHIFT
BLUE VSHIFT
RED VSHIFT
GREEN VSHIFT
BLUE VSHIFT
MENU SELECT
ADJUST
ADJ-5
SECTION 3 ADJUSTMENTS
<MZ16K/MZ13K/MZ10K>
1.4. Adjusted data transfer
f
Data backup and restore can be done via the LAN terminal. This function cannot be used with SERIAL terminal connection.
1.4.1. Equipment to be used
1. Computer : Use it for transferring of backup data.
2. Communication cable : LAN cable (When connecting directly, use a cross cable)
3. Service Software : LogTool.exe [Ver. 2.1.0.9~] Download from the projector service website.
1.4.2. Connection Preparations
1. Check the settings of the projector
1) Select the sub menu [NETWORK CONTROL] of main menu [NETWORK] and set the [TYPE] to [LAN].
2) Check the network IP address of the projector and take a note.
3) Set the IP address of computer to approximate (same network group) value of the projector IP address.
• If you have changed the each menu settings, please return settings to the original (users) after work.
2. Connect the projector and the PC by using a communication cable.
LAN cable (straight)
LAN cable (straight)
Projector LAN
Computer
Hub
Connection example
1.4.3. Backup the adjusted data (before PCB exchange)
1. Turn the projector to "Normal-Standby" mode. (ON(G)/STANDBY)R) LED turns in red.)
2. Start up service software [LogTool.exe] with a computer.
3. The projector connection setting window appears.
1) Select [Option] → [Password] to display the password input window.
2) Enter the service password [ 1565z ] and then click [OK] button.
①
②
③
• The e-mail address cannot be backup. After completing the work, you need to re-setup the e-mail address.
• The NFC activation cannot be backup if activated with the NFC upgrade kit. Explain it to users to reactivate.
ADJ-6
SECTION 3 ADJUSTMENTS
<MZ16K/MZ13K/MZ10K>
①
③
②
4. Select [LAN] of connection method and setup the connection information to connect to the projector.
🅰 In case of known IP address of projector
• Select [Manual] and setup the [IP address, Port (Command Port)] and then click [Connect] button.
①
②
③
• After searching result, the available projectors are listed on the window as the below.
Check mark the projector for which you want to acquire the system log and then click [OK] button.
🅱 In case of unknown IP address of projector
• Select [Search] and setup the [IP Address/subnet mask] to the same network of the projector and [Port(Command
port)] and then click [Search] button.
④
⑤
ADJ-7
SECTION 3 ADJUSTMENTS
<MZ16K/MZ13K/MZ10K>
5. Read the EEPROM data file by the following procedure.
① Select the projector name to read of EEPROM data.
② Select a [Service] tab.
③ Click [Receive] button.
6. Select the save place and click [Save(S)] button.
7. The data save is complete when the "Complete" dialog window appears.
Click [OK] button to close the window.
③
①
②
Click on the first or last page to see other PT-MZ16K / PT-MZ13K / PT-MZ10K (serv.man2) service manuals if exist.