Panasonic PT-LW373 / PT-LW333 / PT-LB423 / PT-LB383 / PT-LB353 / PT-LB303 (serv.man3) Service Manual ▷ View online
9
PREFACE
<LW373/LW333/LB423/LB383/LB353/LB303>
ENGLISH - 111
Dimensions
<Unit : mm (inch)>
335 (13-3/16")
87 (3-7/16")
250 (9-27/32")
252 (9-29/32")
61 (2-13/32")
9 (11/32")
96 (3-25/32")
167.5 (6-19/32")
68.5 (2-11/16")
55 (2-5/32")
Actual dimension may differ by product.
*1 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*2
For details of video signals that can be projected using this projector, refer to “List of compatible signals”. (x page 107)
*3
Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
*4 Only for PT-LW373, PT-LW333, PT-LB423, PT-LB383 and PT-LB353.
*5 This is an average value. It may differ depending on individual product.
*5 This is an average value. It may differ depending on individual product.
*6 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*7 [Lamp control] will be switched to [
*7 [Lamp control] will be switched to [
(Eco 1)] automatically when [High land] is set to [Off] and the operating environment temperature is 35 °C to 40 °C.
[Lamp control] will be switched to [
(Eco 1)] automatically when [High land] is set to [On 1] or [On 2] and the operating environment temperature
is 30 °C to 35 °C.
Note
f The part numbers of accessories and separately sold components are subject to change without notice.
Chapter 7 Appendix - Dimensions
n
Dimensions
10
PREFACE
<LW373/LW333/LB423/LB383/LB353/LB303>
SECTION
1
INF-1
SECTION 1 SERVICE INFORMATION
(2017-01)
CONTENTS
1. Circuits Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-2
1. 1. Thermal switch
1. 2. Lamp cover switch
1. 3. Fuse (F2003)
1. 2. Lamp cover switch
1. 3. Fuse (F2003)
2. Maintenance/Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-3
2. 1. Maintenance
2. 2. Replacing the Unit
2. 3. How to check the lamp runtime
2. 4. Cleaning
2. 2. Replacing the Unit
2. 3. How to check the lamp runtime
2. 4. Cleaning
3. Notes on service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-10
3. 1. Before service operation
3. 2. Service
3. 3. Security functions
3. 4. Standby mode
3. 5. How to change the baud rate of serial communication port
3. 2. Service
3. 3. Security functions
3. 4. Standby mode
3. 5. How to change the baud rate of serial communication port
4. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INF-14
4. 1. LED indicators
4. 2. Shutdown system
4. 3. Error log
4. 4. Troubleshooting chart
4. 5. I/O port functions
4. 2. Shutdown system
4. 3. Error log
4. 4. Troubleshooting chart
4. 5. I/O port functions
INF-2
SECTION 1 SERVICE INFORMATION
<LW373/LW333/LB423/LB383/LB353/LB303>
1. Circuits Protection
This projector provides the following circuit protections to operate in safety. If the abnormality occurs inside the projector, it will
automatically turn off by operating one of the following protection circuits.
automatically turn off by operating one of the following protection circuits.
1. 1. Thermal switch
There is a thermal switch inside of the projector to detect the inter-
nal temperature rising abnormally. When the internal temperature
around lamp reaches near 120°C , the thermal switch will open to
cut off the power supply to the lamp power circuit.
The thermal switch is not reset to normal automatically even if the
internal temperature becomes normal. Please reset the thermal
switch following to the procedure below.
cut off the power supply to the lamp power circuit.
The thermal switch is not reset to normal automatically even if the
internal temperature becomes normal. Please reset the thermal
switch following to the procedure below.
How to reset the thermal switch
1. Remove the cabinet top case.
2. Press the reset button on the thermal switch.
2. Press the reset button on the thermal switch.
Caution:
Before press the reset button, disconnect the AC cord from the projector.
1. 2. Lamp cover switch
The lamp cover switch cuts off the drive signal to the lamp circuit
when the lamp cover is removed or not closed completely. After open-
ing the lamp cover for replacing the lamp unit, place the lamp cover
correctly otherwise the projector cannot turn on.
ing the lamp cover for replacing the lamp unit, place the lamp cover
correctly otherwise the projector cannot turn on.
1. 3. Fuse (F2003)
A fuse is located inside of the projector. When the ON (G)/STAND-
BY (R) indicator is not lighting, the fuse may be opened. Please
check the fuse as following steps.
The fuse should be used with the following type;
check the fuse as following steps.
The fuse should be used with the following type;
Fuse Part No.: K5E632YY0007
TYPE VBS UBM 6.3A 250V (PF) FUSE
CONQUER. TYPE VBS UBM
TYPE VBS UBM 6.3A 250V (PF) FUSE
CONQUER. TYPE VBS UBM
How to replace the fuse
1. The fuse is placed on the filter board. Remove the cabinet
top according to the section 2 "Mechanical Disassembly".
2. Take the fuse off from the fuse holder, then replace the new
one with the specified type.
Fuse
(F2003)
(F2003)
Thermal fuse
Lamp cover switch
Click on the first or last page to see other PT-LW373 / PT-LW333 / PT-LB423 / PT-LB383 / PT-LB353 / PT-LB303 (serv.man3) service manuals if exist.