DOWNLOAD Panasonic PT-LW373 / PT-LW333 / PT-LB423 / PT-LB383 / PT-LB353 / PT-LB303 (serv.man3) Service Manual ↓ Size: 20.74 MB | Pages: 70 in PDF or view online for FREE

ADJ-3

[Before]
- 

Input a 100% white signal. 

1. Adjust the condenser lens (OUT) to obtain a completely white screen. 

  1) In case the shadow appears on the left or right edge of the   

      screen. Loosen 1 screw A and move the condenser lens unit  

      right or left to disappear the shadow on the screen. (Fig2-1)

  2) In case the shadow appears on the top or bottom edge of the 

      screen. Loosen 2 screws B and move the condenser lens unit 

      upper or lower to disappear the shadow on the screen. (Fig.2-2)

2. Tighten screws A and B to fix the condenser lens unit. 

Fig. 2-2 

Completely 

white screen

Completely 

white screen

Fig. 2-1 

a

b

y

x

x

B

B

y

a

A

b

ADJ-4

To enter the "Service Mode", press and hold the MENU button and  button on the projector for more than 3 seconds or press 

and hold the MENU button on the remote control for more than 20 seconds.

The service menu appears on the screen as follows. 

1. Select the adjusting items "Group", "No." or "Data" by pressing the MENU button repeatedly. The red cursor will 
    move to show the selected item.
2. To change the value of selected item, press the  or  button repeatedly. Refer to the "Service adjustment 
    data table" for further information. 

Press 

 to exit the service mode. 

Service Mode       PANASONIC
Input 

     Computer 1 

Image            Dynamic
Group 

No. 

Data

  200              

1

             

0

 Ver.

             

  1.00             XXXXX

 

Group No.

F/W version

Item No.

Data value

ADJ-5

*  Before setting, check which type of Optical block is used by 

  the projector according to the "Optical block removal" 

  chapter in Optical Parts Disassembly.

1. Enter the service mode.
2. Optical block type check
Select Group 290 and No. 0 to check the following values;

  Data "0" 

:  L-type Optical block

  Data "20"  

:  R-type Optical block

  If the installed type of Optical block is different from the  
  set display mode, perform the following procedures.
3. Optical block type mode setting

    Select Group 290 and No. 1, set the Data value between 

10 and 0 or 20 according to the Optical block type. When     

   the value reaches 0 or 20, it will return to 10. 

    Equipment 

Digital voltmeter

1. Enter the service mode.
2. Connect the digital voltmeter to the test points listed 
    below.
3. Select Group no. 250, No. 0 and change the Data 

    value to adjust the reading of voltmeter to be 

    specified value.

4. Adjust the remaining adjustments of the No. 1 to 5 
    listed below.

 

Group-No. 

Test Points  

Adjustment value

  250  -  0 

FAN-A1  

4.0 ±0.1Vdc

  250  -  1 

FAN-A1  

12.5 ±0.1Vdc

  250  -  2 

FAN-B1  

4.0 ±0.1Vdc

  250  -  3 

FAN-B1  

12.5 ±0.1Vdc

  250  -  4 

FAN-C1  

4.0 ±0.1Vdc

  250  -  5 

FAN-C1  

12.5 ±0.1Vdc

 

  Input signal            No signal

1.  Enter the service mode.
2.   

Select Group No.30 and change Data value as follows.  

  Obtain the minimum screen flickering value by adjusting   

     the value. 
 

Group-No.      Adjustment

 

30 - 3 

Red flickering

 

30 - 4 

Green flickering 

 

30 - 5 

Blue flickering

     Input signal No signal

1.   

Put the projector on a horizontal place with the adjust-
able feet being minimum range and then enter the

      service mode. 
2.  Select Group 102, No.3 and set data value from 0 to 5. 

3.   By pressing the INPUT/ENTER button, the Keystone 

  Offset adjustment will start. 

4.    When it has completed, the "OK" message will appear 

on the screen. 

5.    By pressing any button on the projector or the remote  

  control, the "OK" message will disappear.  

  (Data value of Group 102, No.3 will be back to 0 for

      initial value.)

ADJ-6