DOWNLOAD Panasonic PT-LB80NTU / PT-LB80NTE / PT-LB80NTEA / PT-LB80U / PT-LB80E / PT-LB80EA / PT-LB75NTU / PT-LB75NTE / PT-LB75NTEA / PT-LB75U / PT-LB75E / PT-LB75EA Service Manual ↓ Size: 12.86 MB | Pages: 118 in PDF or view online for FREE

Model
PT-LB80NTU PT-LB80NTE PT-LB80NTEA PT-LB80U PT-LB80E PT-LB80EA PT-LB75NTU PT-LB75NTE PT-LB75NTEA PT-LB75U PT-LB75E PT-LB75EA
Pages
118
Size
12.86 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / LCD PROJECTOR
File
pt-lb80ntu-pt-lb80nte-pt-lb80ntea-pt-lb80u-pt-lb80.pdf
Date

Panasonic PT-LB80NTU / PT-LB80NTE / PT-LB80NTEA / PT-LB80U / PT-LB80E / PT-LB80EA / PT-LB75NTU / PT-LB75NTE / PT-LB75NTEA / PT-LB75U / PT-LB75E / PT-LB75EA Service Manual ▷ View online

8 Measurement and Adjustments
When the following components in this projector are replaced, adjustments are required. Adjust each item according to the table
below.
8.1. Cautions for Adjustment
     ·    
Never unplug the power cord until the power indicator on the projector illuminates red.
     ·    
To maintain and ensure safety, always use the designated components for replacement parts.
     ·    
If removing any clamps, lead wires or connectors, always place them back in their proper locations.
     ·    
Be careful not to damage the lead wires or components when using a soldering iron or similar tool.
8.2. Setting Before Adjustment
     ·    
Set up the projector to obtain the projection distance below.
     ·    
Turn the zoom ring of the projector to obtain the largest size of the picture.
8.3. Convergence Adjustment
Execute this adjustment when replacing the LCD panel (B) .
8.3.1. Tools to be used
Service Kit (Part No. TZSH07026) : This kit is composed of 3 extension flexible cables.
Note:
     ·    
Consult your dealer or Authorized Service Center for the service kit.
8.3.2. Preparation
 1. Loosen 2 screws fixing the panel adjuster and 2 screws fixing the panel attachment, then tighten the 4 screws temporarily just
until the LCD panel can be shifted by your fingers.
Note:
     ·    
See figures in the section 7.13. "Replacement of LCD Panel (B)" for 2 screws fixing the panel adjuster and 2 screws
fixing the panel attachment.
 2. Reassemble the projector in the reverse order of disassembling, but leave the upper case and the screws fixing the A-
P.C.Board block as they are removed.
 3. Connect the service kit (extension flexible cables).
     ·    
Each flexible cable of LCD Panels (R/G/B) - Connectors (A1/A2/A3) on A-P.C.Board
21
PT-LB80NTU / PT-LB80NTE / PT-LB80NTEA / PT-LB80U / PT-LB80E / PT-LB80EA / PT-LB75NTU / PT-LB75NTE / PT-LB75NTEA / PT-LB75U / PT-LB75E / PT-LB75EA
 4. Covering with an insulator (cloth or the like) to prevent a short circuit, set the A-P.C.Board block on the main unit.
Note:
     ·    
Handle with care not to apply external force to connecting parts which connect the main unit and A-P.C.Board.
8.3.3. Adjustment Procedure
Prepare 2 pieces of thick black paper (23 mm × 100 mm) that can be shaded.
     ·    
Cover and shade LCD panels (R) and (G) with the paper.
 1. Display the green crosshatch pattern and adjust the lens focus.
 2. Display green and blue crosshatch patterns.
 3. Adjust focus by shifting the panel adjuster for LCD panel (B) back and forth, then tighten the 2 screws.
 4. Adjust the LCD panel (B) position so that the vertical center of blue crosshatch pattern is overlapped with the vertical center of
green crosshatch pattern.
 5. Adjust the LCD panel (B) position so that the horizontal center of blue crosshatch pattern is overlapped with the horizontal
center of green crosshatch pattern.
 6. Correct the tilt of the blue crosshatch pattern by adjusting the LCD panel (B) position.
 7. Display green, red and blue crosshatch patterns and confirm the convergence. If it is necessary, fine adjust the convergence
so that the blue crosshatch pattern is overlapped with green one.
Repeat steps (1) to (3) until the green and blue crosshatch
patterns merge into a cyan pattern.
 8. After the adjustment, reassemble the projector according to the steps 8 in the section 7.13. "Replacement of LCD Panel (B)".
8.4. Software for Adjustment
8.4.1. Outline
     ·    
This projector needs computer-aided adjustments.
     ·    
After the software adjustments, this projector must be turned off and on again to memorize the settings.
     ·    
Connect the cable between the projector and a PC as shown below.
     ·    
Updating the software will change the version number.
22
PT-LB80NTU / PT-LB80NTE / PT-LB80NTEA / PT-LB80U / PT-LB80E / PT-LB80EA / PT-LB75NTU / PT-LB75NTE / PT-LB75NTEA / PT-LB75U / PT-LB75E / PT-LB75EA
8.4.2. Operating Procedure
 1. Run software program by the keyboard entry.
Note:
     ·    
Use the software program as below.
Adjustment Tool [PT-LB80, LW80 Series]
 2. The first menu is Port selection menu.
 3. Adjust the projector by selecting the necessary item from the menu in each stage.
8.4.3. Port Selection Menu
Select the applying item with the list box and click "Data" or "Adjustment".
8.4.3.1. Explanation of Buttons
Port:
Port name of PC which connects with the projector
Data:
Displays the data setting menu.
Adjustment:
Displays the adjustment menu.
Exit:
Exits this application.
23
PT-LB80NTU / PT-LB80NTE / PT-LB80NTEA / PT-LB80U / PT-LB80E / PT-LB80EA / PT-LB75NTU / PT-LB75NTE / PT-LB75NTEA / PT-LB75U / PT-LB75E / PT-LB75EA
8.4.4. Data Setting Menu
8.4.4.1. Explanation of Buttons
Micom Data Transmission:
Reads the microcomputer data from the file and transmits it to the projector.
Micom Data Reception:
Receives the microcomputer data from the projector and writes it in the file.
Gamma Data Transmission:
Reads the gamma data from the file and transmits it to the projector.
Gamma Data Reception:
Receives the gamma data from the projector and writes it in the file.
Uniformity Data Transmission:
Reads the color unevenness correction data from the file and transmits it to the projector.
Uniformity Data Reception:
Receives the color unevenness correction data from the projector and writes it in the file.
Serial Number
Displays the serial number setting menu.
Log Display
Displays the log receiving menu.
Exit:
Exits this application.
8.4.4.2. Receiving and transmitting of the data
Click a target button and specify a file name.
8.4.4.3. Setting the Serial Number
Set the serial number if the A-P.C.Board is replaced and the product serial number disappears.
Note:
     ·    
Set the projector into standby mode (POWER indicator on the projector illuminated red), and execute the procedure in
24
PT-LB80NTU / PT-LB80NTE / PT-LB80NTEA / PT-LB80U / PT-LB80E / PT-LB80EA / PT-LB75NTU / PT-LB75NTE / PT-LB75NTEA / PT-LB75U / PT-LB75E / PT-LB75EA
Page of 118
Display

Click on the first or last page to see other PT-LB80NTU / PT-LB80NTE / PT-LB80NTEA / PT-LB80U / PT-LB80E / PT-LB80EA / PT-LB75NTU / PT-LB75NTE / PT-LB75NTEA / PT-LB75U / PT-LB75E / PT-LB75EA service manuals if exist.