Panasonic PT-JX200HBU / PT-JX200HWU / PT-JX200GBE / PT-JX200GWE / PT-JX200GBD / PT-JX200GWD (serv.man2) Service Manual ▷ View online
4
PREFACE
< JX200 >
r
Mount the projector to the track system which is installed in the horizontal ceiling or
beam and can withstand the weight of the projector .
Mounting the projector to the following track system will result in fire, electric shocks, or falling of the projecto .
f
Track system that is installed in the wall surface
f
Track system that is installed in the sloping ceiling or beam
f
Track system that cannot withstand the load
f
Track system that is installed on the floo
Cannot be installed
r
Focus adjustment
The projection lens is thermally affected by the light from the light source, making the focus unstable in the period
just after switching on the power. It is recommended that images be projected continuously for at least 30 minutes
before the focus is adjusted.
r
Cautions when setting up the projector
f
Do not block the ventilation ports (intake and exhaust) of the projector.
f
Prevent hot and cool air from the air conditioning system to blow directly to the ventilation ports (intake and
exhaust) of the projector.
f
Do not install the projector in a confined space.
When installing the projector in a confined space, provide air conditioning or ventilation separately. Exhaust heat
may accumulate when the ventilation is not enough, triggering the protection circuit of the projector.
5
PREFACE
< JX200 >
CONTENTS
1. Safety Precautions
2. Specifications
2. Specifications
SECTION 1 SERVICE INFORMATION
1. The name of each part
2. Menu Navigation
3. Service Mode
4. Notes on service
5. Troubleshooting
2. Menu Navigation
3. Service Mode
4. Notes on service
5. Troubleshooting
SECTION 2 DISASSEMBLY PROCEDURES
1. Parts Locations
2. Disassembly Instructions
2. Disassembly Instructions
SECTION 3 ADJUSTMENTS
1. Adjustment item and a procedure
2. Firmware Update Procedure
2. Firmware Update Procedure
SECTION 4 SCHEMATIC DIAGRAM
1. Block Diagram
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram
6
PREFACE
< JX200 >
1. Safety Precautions
1. 1. General Guidelines
- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this projector.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed
and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated or damaged
by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C combi-
nations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.
1. 2. Leakage Current Check
1. Prepare the measuring circuit as shown in Fig.1.
Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75mA or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer
because of a possibility of an electric shock.
M1
M2
Rs
Cs
Rb
10KΩ ±0.1%
0.022µF
±1.0%
Vb
(V) V
Rs: 1500 Ω±0.1%
Cs: 0.22 µF±1.0%
Rb: 500 Ω±0.1%
to T1
or T2
in FIg.2
Weighted leakage current=Vb / 500 (A)
Fig. 1
Isolation transformer
T1
T2
connection
to power outlet
M1
M2
Fig.2
Projector
Measuring
Circuit (Fig.1)
Performance
Voltmeter
(rms reading)
Accurancy:
≤ 2%
Input resistance:
≥ 1 MΩ
Input capacitance: ≤ 200 pF
Frequency range: 15 Hz to 1 MHz
Table. 1
7
PREFACE
< JX200 >
2. Specifications
2. 1. Specifications
The specifications of the projector are as follows.
▪PT-JX200HBU/JX200HWU
Model No.
PT-JX200HBU/PT-JX200HWU
Power supply
120 V ~ (120 V alternating current), 50 Hz/60 Hz
Power consumption
240 W (2.3 A)
In standby mode (when [STANDBY MODE] is set to [ECO]): 0.4 W
In standby mode (when [STANDBY MODE] is set to [ECO]): 0.4 W
*1
In standby mode (when [STANDBY MODE] is set to [NETWORK]): 0.5 W
*2
In standby mode (when [STANDBY MODE] is set to [NORMAL] and the fans are stopping): 12 W
DLP chip
Size
14.0 mm (0.55") (aspect ratio 4:3)
Display system
1-unit DLP chip, DLP type
Number of pixels 786 432 pixels (1 024 x 768 dots)
Lens
Electric zoom
1.3 to 2.9:1
Electric focus
F = 2.0 to 2.7
f = 15.2 mm to 32.7 mm
Light source
Laser diode (Maximum output: 36 W x 2, Wavelength: 452 - 458 nm)
Light output
*3
2 000 lm (ANSI)
Contrast ratio
*3
1 000:1
Projected image size
0.76 m (30") to 5.08 m (200")
Screen aspect ratio
4:3
Projection method
[FRONT]/[REAR]
(On/off of vertical flip can be set with [VERTICAL FLIP])
Card slot
SD card slot
*4
x 1 (supports SDHC memory card)
Outer case
Molded plastic
Outer color
PT-JX200HBU: Black, PT-JX200HWU: White
Weight
4.5 k] (9.92 lbs.)
Noise level
*3
When [LIGHT POWER] is set to [NORMAL]: 33 dB
When [LIGHT POWER] is set to [ECO]: 30 dB
Operating
environment
Temperature
*5
0 °C (32 °F) to 40 °C (104 °F)
Humidity
10 % to 80 % (no condensation)
Remote
control
Power supply
DC 3 V (AAA/R03 or AAA/LR03 battery x 2)
Operating range Within approx. 7 m (22'11") (when operated directly in front of signal receiver)
Weight
Weight
63 ] (2.2 ozs.) (including batteries)
Dimensions
Width: 44 mm (1-23/32"), Height: 105 mm (4-1/8"), Depth: 20.5 mm (13/16")
*1 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO], the network function (both wireless LAN and wired LAN)
cannot be used in standby mode.
*2 When the [SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NETWORK], the network function while in standby mode is
restricted to the projector operations via wired LAN using the Wake on LAN function.
*3 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*4 Operations of the Panasonic SD memory card up to capacity of 2 GB and Panasonic SDHC memory card up to capacity of 32 GB are confirmed.
*5 The operating environment temperature should be between 0 °C (32 °F) and 35 °C (95 °F) when using the projector at elevations between 1 000 m
(3 281') and 2 700 m (8 858') above sea level.