Panasonic PT-JX200HBU / PT-JX200HWU / PT-JX200GBE / PT-JX200GWE / PT-JX200GBD / PT-JX200GWD (serv.man2) Service Manual ▷ View online
2
PREFACE
< JX200 >
Notice on laser
■
U model
This projector is the Class 3R laser product that complies with IEC 60825-1:2007.
■
U model
This projector is the Class 1 laser product that complies with IEC/EN 60825-1:2014.
■
Inside of product
CAUTION
About lead free solder (PbF)
This projector is using the P.C.Board which applies lead free solder.
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
Notes:
• Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder Typically
the melting point is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation func-
tion and set it to 370 ± 10 °C.
• Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx.
600°C or higher).
• Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead
solder, use lead solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before
applying lead solder.)
• After solder to double layered P.C Boards, check the component side for excess solder which may flow onto the opposite side.
About the identification of the lead free solder P.C.Board.
For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
or the back of P.C.Board.
PbF
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.
Le technicien d'entretien doit lire et suivre les «Précautions de sécurité» et «Avis important de sécurité» dans ce manuel d'entretien.
7
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Prod-
ucts powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair
the product or products dealt with in this service information by anyone else could result in serious injury or death.
7
AVERTISSEMENT
Ce document d'entretien est destiné aux techniciens d'entretien expérimentés uniquement et n'est pas conçu pour une utilisation par le
grand public. Il ne contient pas des avertissements ou des mises en garde pour aviser les non-techniciens des dangers potentiels lorsqu'ils
tentent de réparer un produit. Les appareils alimentés par l'électricité doivent être révisés ou réparés uniquement par des techniciens pro-
fessionnels expérimentés. Toute tentative d'entretenir ou de réparer le ou les produits traités dans ce document d'entretien par autrui peut
entraîner des blessures graves ou la mort.
WARNING : Use laser Light Radiation eye and skin protection during servicing
AVERTISSEMENT : Utilisez laser lumière oeil radioprotection et la protection de la peau lors de l'entretien
CAUTION / MISE EN GARDE
Lithium Battery
Risk of explosion if battery is replaced by an incorrect type,
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Batterie au lithium
Risque d'explosion si la batterie est remplacée par un type incorrect,
Remplacez-la uniquement par le même type ou le type équivalent recommandé par le fabricant.
Jetez les batteries usagées conformément aux instructions du fabricant.
チチƷチチᬼယყଙڻǾոᄃყଙǺ᭩ڻǾ℉ȡᇷ⯶ǤǪǹǓǢǷ
DPQT1025ZA
ュモワヨユンノヤロモヴヴチフチロモヴユンチンモュリモヵリヰワチヸラユワチヰヱユワチモヷヰリュチユヺユチヰン
チチチチチチチチチチチチチチチチチチチヴレリワチユヹヱヰヴヶンユチヵヰチュリンユヤヵチヰンチヴヤモヵヵユンユュチンモュリモヵリヰワ
ュモワヨユンノンモヺヰワワユヮユワヵチロモヴユンチュユチヤロモヴヴユチフチノチユワチヤモヴチュトヰヶヷユンヵヶンユチ
ュモワヨユンノンモヺヰワワユヮユワヵチロモヴユンチュユチヤロモヴヴユチフチノチユワチヤモヴチュトヰヶヷユンヵヶンユチ
チチチチチチチチチチチチチチチチチチユヹヱヰヴリヵリヰワチュモワヨユンユヶヴユチモヶチンモヺヰワワユヮユワヵチュリンユヤヵチヰヶチ
チチチチチチチチチチチチチチチチチチュリョョヶヴチュユヴチヺユヶヹチヰヶチュユチロモチヱユモヶ
3
PREFACE
< JX200 >
CAUTION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one of the following measures:
f Reorient or relocate the receiving antenna.
f Increase the separation between the equipment and receiver.
f Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
f Consult the dealer or an experienced radio/BD technician for help.
CAUTION:
Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
There are special components used in this equipment which are important for safety. These parts are marked by 7 in the schematic
diagram, circuit board diagrams, exploded views and replacement parts list. It is essential that these critical parts should be replaced
with manufacturer’s specified parts to prevent shock, fire, or other hazards. Do not modify the original design without permission of
manufacturer.
IMPORTANT SAFETY NOTICE
Cautions when installing
r
Do not set up the projector outdoors.
The projector is designed for indoor use only.
r
Do not set up the projector in the following locations.
f
Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal
components or malfunction.
f
Locations near the sea or areas affected by corrosive gas: Corrosion may cause the projector to fall off, shorten
the life of the parts or cause the projector to malfunction.
f
Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare
cases due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from
the projector or other equipment, or the air from the air conditioner does not blow toward the front of the main
unit of the projector.
f
Places with sharp temperature fluctuations near lights (such as studio lamps): Doing so may result in
deformation of the projector due to heat, which may cause malfunctions.
The operating environment temperature of the projector should be between 0 °C (32 °F) and 40 °C (104 °F)
The operating environment temperature of the projector should be between 0 °C (32 °F) and 40 °C (104 °F)
when using it at elevations lower than 1 000 m (3 281') above sea level, and between 0 °C (32 °F) and 35 °C
(95 °F) when using it at elevations between 1 000 m (3 281') and 2 700 m (8 858') above sea level.
f
Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
f
Places where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage
to the DLP chip.
r
Do not install the projector at elevations of 2 700 m (8 858') or higher above sea level.
Doing so may shorten the life of the components and result in malfunctions.
4
PREFACE
< JX200 >
r
Mount the projector to the track system which is installed in the horizontal ceiling or
beam and can withstand the weight of the projector .
Mounting the projector to the following track system will result in fire, electric shocks, or falling of the projecto .
f
Track system that is installed in the wall surface
f
Track system that is installed in the sloping ceiling or beam
f
Track system that cannot withstand the load
f
Track system that is installed on the floo
Cannot be installed
r
Focus adjustment
The projection lens is thermally affected by the light from the light source, making the focus unstable in the period
just after switching on the power. It is recommended that images be projected continuously for at least 30 minutes
before the focus is adjusted.
r
Cautions when setting up the projector
f
Do not block the ventilation ports (intake and exhaust) of the projector.
f
Prevent hot and cool air from the air conditioning system to blow directly to the ventilation ports (intake and
exhaust) of the projector.
f
Do not install the projector in a confined space.
When installing the projector in a confined space, provide air conditioning or ventilation separately. Exhaust heat
may accumulate when the ventilation is not enough, triggering the protection circuit of the projector.
5
PREFACE
< JX200 >
CONTENTS
1. Safety Precautions
2. Specifications
2. Specifications
SECTION 1 SERVICE INFORMATION
1. The name of each part
2. Menu Navigation
3. Service Mode
4. Notes on service
5. Troubleshooting
2. Menu Navigation
3. Service Mode
4. Notes on service
5. Troubleshooting
SECTION 2 DISASSEMBLY PROCEDURES
1. Parts Locations
2. Disassembly Instructions
2. Disassembly Instructions
SECTION 3 ADJUSTMENTS
1. Adjustment item and a procedure
2. Firmware Update Procedure
2. Firmware Update Procedure
SECTION 4 SCHEMATIC DIAGRAM
1. Block Diagram
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram
