PT-JW130GWE, PT-JW130GBE (serv.man2) — Panasonic Projector Service Manual (repair manual). Page 2

View Panasonic PT-JW130GWE / PT-JW130GBE (serv.man2) Service Manual online

PREFACE
<PT-JW130>
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.
Notice on laser
This projector is the Class 2 laser product that complies with IEC 60825-2007.
This projector is a Class 2 laser product, is equipped with a Class 4 laser module to an inside.
CAUTION
    Lithium Battery
    Precaution
    About lead free solder (PbF)
This projector is using the P.C.Board which applies lead free solder.
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
Notes:
 Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder. Typically the melting point
 is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation function and set it to 370 ± 10 °C.
 Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 600°C or higher).
 Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead solder, use lead
 solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before applying lead solder.)
 After soldering to double layered P.C.Boards, check the component side for excess solder which may flow onto the opposite side.
About the identification of the lead free solder P.C.Board.
  For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
  or the back of P.C.Board.
WARNING
  This service information is designed for experienced repair technicians only and is not designed for use by the general public.
  It dose not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
  Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
  or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
WARNING : Use Laser Light Radiation eye and skin protection during servicing
If using of this projector at high altitudes (above 1,400m), set HIGHT ALTITUDE MODE to “ON”.
(Refer to “PROJECTOR SETUP menu” in Operating Instructions.)
Failure to observe this may cause malfunctions. Never use this projector at an altitude of 2,700m or higher.
Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations.
Risk of explosion if battery is replaced by an incorrect type,
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
AVERTISSEMENT : Utilisez laser lumière œil radioprotection et la protection de la peau lors de l'entretien
or
TQFX513
IEC / EN 60825-1 : 2007
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
WAVE LENGTH:448-462nm
MAXIMUM OUTPUT:53.0mW
PULSE DURATION:1.2ms
IEC / EN 60825-1 : 2007
RAYONNEMENT LASER 
NE PAS REGARDER DANS LE 
FAISCEAU APPAREIL À LASER 
DE CALSSE2
LONGUEURS D'ONDES:
448-462nm
MAXIMALE DU RAYONNEMENT:
53.0mW
DURÉE DE L'IMPULSION:
1.2ms
TQFX514
CAUTION-CLASS 4 LASER RADIATION WHEN OPEN AVOID EYE OR
SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION
ATTENTION-RAYONNEMENT LASER DE CLASSE 4-EN CAS
D'OUVERTURE EXPOSITION DANGEREUSE AU
RAYONNEMENT DIRECT OU DIFFUS DES YEUX OU DE
LA PEAU
TQFX338AB
2
Page of 92
Display

Click on the first or last page to see other PT-JW130GWE / PT-JW130GBE (serv.man2) service manuals if exist.