Panasonic PT-EZ57 Service Manual ▷ View online
DIS-3
SECTION 2 DISASSEMBLY PROCEDURES
<EZ57>
1.3. Mechanical parts location
1.4. Optical parts location
Prism cover
Filter cover
Intake fan holder 1
Intake fan holder 2
Intake duct assy
Air filter unit
Top case
Lighting block
PBS duct
AC inlet
Terminal dust cover
Operation button
Power duct holder
Speaker case
Lamp cover
Terminal cover
G-Polarizer
R-Polarizer
Projection lens &
optical block *
B-Polarizer
Lighting case top
Lighting case bottom
PBS
Integrator lens-out
Integrator lens-in
Integrator lens-in
Lamp unit
Power box
Lamp house
Lamp fan holder
Bottom case
Duct top cover
Lens cover bottom
Lens cover top
LED light guide
Front cover
* Projection lens & mounter and optical block are not supplied separately. Only they will be
supplied as an assembled parts.
DIS-4
SECTION 2 DISASSEMBLY PROCEDURES
<EZ57>
2. Disassembly Instructions
[Caution]
* Before disassembly the projector, turn off the power switch and disconnect the power plug from the wall outlet.
* During the disassemble work, please wear gloves to protect your hands from metal parts and shield plate.
* Electrical parts such as PCBs, may get damaged by electrostatics discharge and/or surges which affects the set reliability.
Please take care for electrostatic discharges by using grounded wrist straps to release the electricity from the body.
* When tore off sticky tapes, please use a new thing without reusing it on the occasion of assembling.
Please use the special table pad specified below or substitution when disassembling and assembling.
Place the projector onto the special table pad to disassemble and assemble.
Place the projector onto the special table pad to disassemble and assemble.
When mounting the lighting case or duct block onto the cabinet bottom case, the cabinet bottom case might be bent due to
applying the over power force.
As the result, the tiny gap will be come up between the air duct and cabinet bottom case. This gap have an effect on the
temperature control inside projector.
applying the over power force.
As the result, the tiny gap will be come up between the air duct and cabinet bottom case. This gap have an effect on the
temperature control inside projector.
Before disassembling and assembling
500 (19.7)
250 (9.8)
70 (2.76)
70 (2.76)
70 (9.45)
70 (2.76)
70 (2.76)
100 (3.94)
10 (0.39)
310 (12.2)
Special table pad
Table pad demensions mm (inches)
DIS-5
SECTION 2 DISASSEMBLY PROCEDURES
<EZ57>
2.1. Disassembly flow chart
* Follow the flow chart below when disassembling.
Cable reforming
2.11. G, R/B, PBS intake fan removal
2.10. Duct assy removal
2.9. Power box removal
2.8. Lamp fans assy and lamp house removal
2.7. Lighting block removal
2.6. Front cover removal
2.5. Exhaust fan, [S], [A]/[J]-P.C.Board assy removal
2.4. Top cover removal
2.3. Lamp and lamp cover removal
2.2. Air filter unit, filter cover removal
Completed Product
DIS-6
SECTION 2 DISASSEMBLY PROCEDURES
<EZ57>
2.3. Lamp and lamp cover removal
1. Loosen 1 screw-A and open the lamp cover to slide it in the arrow direction.
2. Loosen 3 screws-B on the lamp and pull it upward off.
A
Lamp
Lamp cover
A
B
B
2.2. Air filter unit, air filter cover removal
1. Put out the air filter cover from the hook of the projector while slightly pushing
upward the tabs of the air filter cover and open it outward.
2. Unhook the hook of air filter unit and take it out.
Air filter unit
Air filter cover
Tabs
Click on the first or last page to see other PT-EZ57 service manuals if exist.