DOWNLOAD Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) Service Manual ↓ Size: 28.13 MB | Pages: 78 in PDF or view online for FREE

Model
PT-DZ8700U PT-DS8500U PT-DW8300U PT-DZ110XE PT-DS100XE PT-DW90XE (serv.man11)
Pages
78
Size
28.13 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / 3-CHIP DLP BASED PROJECTOR
File
pt-dz8700u-pt-ds8500u-pt-dw8300u-pt-dz110xe-pt-ds1.pdf
Date

Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) Service Manual ▷ View online

ORDER NO. BSD1008A26CE 
D10
3-chip DLP Based Projector
Model No.   
PT-DZ8700U 
PT-DS8500U 
PT-DW8300U 
PT-DZ110XE 
PT-DS100XE 
PT-DW90XE 
The projection lens is sold separately. 
Rev.-1  (2017-06)
  PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE   
  
 
   
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual. 
WARNING 
 
This service information is designed for experienced repair technicians only and is not designed for use by the general public. 
 
It dose not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. 
 
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service 
 
or repair the product or products dealt with in this service information by anyone else could result in serious injury or death. 
 
 
WARNING : Use UV Radiation eye and skin protection during servicing. 
 
CAUTION 
Lithium Battery 
    Risk of explosion if battery is replaced by an incorrect type, 
  Replace only with the same of equivalent type recommended by the manufacturer. 
    Dispose of used batteries according to the manufacturer’s instructions. 
 
Precaution 
If using of this projector at high altitudes (above 1,400m), set HIGHT ALTITUDE MODE to “ON”. 
(Refer to “PROJECTOR SETUP menu” in Operating Instructions.) 
Failure to observe this may cause malfunctions. Never use this projector at an altitude of 2,700m or higher. 
Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations. 
 
About lead free solder (PbF) 
This projector is using the P.C.Board which applies lead free solder. 
Use lead free solder in servicing from the standpoint of antipollution for the global environment. 
Notes: 
・Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder. Typically the melting point 
・is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation function and set it to 370 ± 10 °C. 
・Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 600°C or higher). 
・Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead solder, use lead 
・solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before applying lead solder.) 
・After soldering to double layered P.C.Boards, check the component side for excess solder which may flow onto the opposite side.   
About the identification of the lead free solder P.C.Board.   
For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface or the back of 
P.C.Board. 
 
 
 
 
For US 
 
There are special parts used in Panasonic LCD Projectors which are important for safety. These parts are shaded on the schematic diagram. 
It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other hazards. 
Do not modify the original design without permission of PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY.
 
 
WARNING: 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. 
If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, 
The user is encouraged to try to correct the interference by one or more of the following measures. 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
- Consult the dealer or an experienced radio/TV technician for help. 
CAUTION : 
Any unauthorized changes or modifications to this equipment will void the users authority to operate. 
 
IMPORTANT SAFETY NOTICE
  PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE   
  
 
               
CONTENTS 
 
■ Cover Page 
1. Safety Precautions 
2. Specifications 
 
■ SECTION 1 <Service Information> 
1. The name of each part 
2. Menu Navigation 
3. Service Mode 
4. External Controls 
5. Cautions for Service
 
6. Troubleshooting 
   
■ SECTION 2 <Disassembly Procedures> 
1. Parts Location 
2. Disassembly Instructions 
3. Processing of Lead wire 
 
■ SECTION 3 <Adjustment> 
1. Adjustment Procedure 
2. Software update procedure 
 
■ SECTION 4 <Schematic Diagrams> 
1. Block Diagram 
2. Interconnection Block Diagram 
3. Schematic Diagram 
4. Circuit Boards Diagrams 
 
 SECTION 5 <Exploded Views & Replacement Parts List> 
1. Exploded Views 
2. Replacement Parts List 
 
SECTION 6 <Control Commands List> 
 
  PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE   
  
 
1. Safety Precautions 
1.1. General Guidelines 
·  
For continued safety, no modification of any circuit must be 
attempted. 
·  Unplug the power cord from the power outlet before 
disassembling this projector. 
·  Use correctly the supplied power cord and must ground it. 
·  It is advisable to use an isolation transformer in the AC power 
line before the service. 
·  Be careful not to touch the rotation part (cooling fan, etc.) of 
this projector when you service with the upper case removed 
and the power supply turned ON. 
·  Observe the original lead dress during the service. If a short 
circuit is found, replace all the parts overheated or damaged 
by the short circuit. 
·  After the service, all the protective devices such as insulation 
barriers, insulation papers, shields, and isolation R-C 
combinations must be properly installed. 
·  After the service, check the leakage current to prevent the 
customer from getting an electric shock. 
 
1.2. Leakage Current Check 
1.  Prepare the measuring circuit as shown in Fig.1. 
Be sure to use a voltmeter having the performance described in 
Table 1. 
 
 
 
 
 
 
 
 
Fig. 1 
 
Table 1 
 
 
 
 
 
 
 
 
 
Fig. 2 
2.  Assemble the circuit as shown in Fig. 2. Plug the power 
cord in a power outlet. 
3.  Connect M1 to T1 according to Fig. 2 and measure the 
voltage. 
4.  Change the connection of M1 from T1 to T2 and measure 
the voltage again. 
5.  The voltmeter must read 0.375 V or lower in both of steps 3 
and 4. This means that the current must be 0.75mA or less. 
6.  If the reading is out of the above standard, the projector 
must be repaired and rechecked before returning to the 
customer because of a possibility of an electric shock. 
1.3. UV Precaution and UHM Lamp 
Precautions 
·  Be sure to unplug the power cord from the power outlet when 
replacing the lamp. 
·  Because the lamp reaches a very high temperature during its 
operation, wait until it cools completely when replacing the 
Lamp Unit. 
·  The lamp emits small amounts of UV-radiation, avoid 
direct-eye contact with the light. 
·  The lamp unit has high internal pressure. If improperly 
handled, explosion might result. 
·  Because the high pressure lamp involves a risk of failure, 
never touch the lamp wire lead during the service. 
 
 
 
 
Page of 78
Display

Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) Service Manual ▷ Download

  • DOWNLOAD Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) Service Manual ↓ Size: 28.13 MB | Pages: 78 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) Projector. Information contained in Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.