Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man10) Service Manual ▷ View online
PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE
INF-7
6. SELF CHECK
■Self-diagnosing information Displays.
■Self-diagnosing information Displays.
① Main microprocessor Software Version
② Sub microprocessor Software Version
③ Network microprocessor Software Version
④ Geometry Software Version/FPGA Software Version
(No display for DW8300U/DW90XE)
⑤ Emulate setting / Software Version
(No display for DW8300U/DW90XE)
⑤ Emulate setting / Software Version
⑥ Intake Air Temperature (Celsius/Fahrenheit)
⑦ DMD Temperature (Celsius/Fahrenheit)
⑧ Exhaust Air Temperature (Celsius/Fahrenheit)
⑨ Airflow Sensor
(Sensor value/AD conversion value/Correction value)
⑩ LAMP1 Condition (Cumulative Usage Time/ON-OFF)
(Sensor value/AD conversion value/Correction value)
⑩ LAMP1 Condition (Cumulative Usage Time/ON-OFF)
⑪ LAMP2 Condition (Cumulative Usage Time/ON-OFF)
⑫ Fan Condition (1:
normal /0:stop)
From the left : DMD2/DMD1/Color prism/DMD Exhaust/
Synthetic Mirror/Ballast/Power/Lamp2/
Lamp1/ Intake2/ Intake1/ Exhaust-L/
Exhaust-C/ Exhaust-R/
⑬ Brightness sensor Condition
Synthetic Mirror/Ballast/Power/Lamp2/
Lamp1/ Intake2/ Intake1/ Exhaust-L/
Exhaust-C/ Exhaust-R/
⑬ Brightness sensor Condition
⑭ Iris Condition
7. POWER ON SHUTTER
- OPEN: Opens the shutter when power ON.
- CLOSE: Closes the shutter when power ON.
8. POWER OFF MESSAGE
7. POWER ON SHUTTER
- OPEN: Opens the shutter when power ON.
- CLOSE: Closes the shutter when power ON.
8. POWER OFF MESSAGE
Shutter open/close action setting, at the time of the standby operation.
- SHUTTER KEEP: The shutter keeps open or close.
- SHUTTER OPEN: The shutter is opened.
9. ERROR OSD
When I do not watch the error instructions LED of the lamp by a back projection,
the errors of the lamp can be displayed in the OSD.
- ON: OSD does not display the lamp error.
- OFF: OSD display a lamp error.
10. UNIFORMITY
Sets the value of color unevenness correction.
11. CONVERGENCE
When the ingredient of each R/G/B color deviation, revise it electrically.
Specifically, please refer to Clause 1 of SECTION 3 (adjustments).
12. MODEL
After replacing A-PCB, setting the model info.
13. ACF 1) FILTER TYPE ･･･Setting kind of the filter.
- SHUTTER OPEN: The shutter is opened.
9. ERROR OSD
When I do not watch the error instructions LED of the lamp by a back projection,
the errors of the lamp can be displayed in the OSD.
- ON: OSD does not display the lamp error.
- OFF: OSD display a lamp error.
10. UNIFORMITY
Sets the value of color unevenness correction.
11. CONVERGENCE
When the ingredient of each R/G/B color deviation, revise it electrically.
Specifically, please refer to Clause 1 of SECTION 3 (adjustments).
12. MODEL
After replacing A-PCB, setting the model info.
13. ACF 1) FILTER TYPE ･･･Setting kind of the filter.
- NORMAL: Default setting. (Usually)
- SPECIAL: Sets it when the smoke cut filter is installed.
2) ROLL･･･Rewinds the filter once compulsorily.
14. CLOG SENSOR CALIBRATION
Execute the sensor calibration when EEPROM (IC3108 or IC3109) / A-P.C.Board or Airflow sensor (M2-P.C.Board)
is replaced.
Please refer to Clause 1 of SECTION 3 (Adjustments) for the procedure.
2) ROLL･･･Rewinds the filter once compulsorily.
14. CLOG SENSOR CALIBRATION
Execute the sensor calibration when EEPROM (IC3108 or IC3109) / A-P.C.Board or Airflow sensor (M2-P.C.Board)
is replaced.
Please refer to Clause 1 of SECTION 3 (Adjustments) for the procedure.
* In the item where there was abnormality, the "OK" is red.
PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE
INF-8
3.3.2 Additional function of each menu
1. PICTURE menu
Additional Function for DYNAMIC IRIS.
- AI WINDOW: Sets the APL detection area.
2. POSITION menu
- DVI EQUALIZER: If noise appears when DVI input, sets the value so that the noise decreases.
3. ADVANCED Menu
- FRAME LOCK: When the input signal is RGB, FRAME LOCK is added.
4. PROJECTOR SETUP Menu
The following choices are added to "EMULATE " of the sub menu "RS-232C" setting.
- MODE_CH(Other companies model) - MODE_BA(Other companies model)
- MODE_NE(Other companies model) - MODE_SA(Other companies model)
- OTHER(Models other than the above-mentioned)
The following items are added to an indication screen of the sub menu "STATUS ".
Page 1 - APPROXIMATE TIME: Prediction remainder time of the filter in ACF.
Page 2 - BALLAST VERSION: Ballast Software Version
Additional Function for DYNAMIC IRIS.
- AI WINDOW: Sets the APL detection area.
2. POSITION menu
- DVI EQUALIZER: If noise appears when DVI input, sets the value so that the noise decreases.
3. ADVANCED Menu
- FRAME LOCK: When the input signal is RGB, FRAME LOCK is added.
4. PROJECTOR SETUP Menu
The following choices are added to "EMULATE " of the sub menu "RS-232C" setting.
- MODE_CH(Other companies model) - MODE_BA(Other companies model)
- MODE_NE(Other companies model) - MODE_SA(Other companies model)
- OTHER(Models other than the above-mentioned)
The following items are added to an indication screen of the sub menu "STATUS ".
Page 1 - APPROXIMATE TIME: Prediction remainder time of the filter in ACF.
Page 2 - BALLAST VERSION: Ballast Software Version
Page 2
- GEOMETRY VERSION: Geometry Software Version/FPGA Software Version
Page 2
- EMULATE – VERSION: Emulate Software Version
Page 4 - FM R VERSION: Formatter Software Version(Configuration/Main Application/Sequence/De-Gamma)
Page 4
- FM G VERSION: Formatter Software Version(Configuration/Main Application/Sequence/De-Gamma)
Page 4
- FM B VERSION: Formatter Software Version(Configuration/Main Application/Sequence/De-Gamma)
Page 5 - TEMP(°C): Intake air temperature / Exhaust air temperature / Optical module temperature
Page 5
- P.SENSOR: Brightness Sensor value
Page 5
- VOLT: Voltage of LAMP1/LAMP2
Page 5
- AIR FLOW: Sensor value / AD conversion value, Sensor Correction value/ AD conversion value
Page 5
- FAN MODE: FAN control mode
Page 5
- CLOG: Filter condition (NONE-)
Page 5
- R-EXST: Condition of Exhaust-R fan [rotational speed ]
Page 5
- C-EXST: Condition of Exhaust-C fan [rotational speed ]
Page 5
- L-EXST: Condition of Exhaust-L fan [rotational speed ]
Page 5
- INTAKE 1: Condition of Intake-1 fan [rotational speed ]
Page 5
- INTAKE 2: Condition of Intake-2 fan [rotational speed ]
Page 5
- LAMP 1: Condition of Lamp-1 fan [rotational speed ]
Page 5
- LAMP 2: Condition of Lamp-2 fan [rotational speed ]
Page 5
- P-UNIT: Condition of Power fan [rotational speed ]
Page 5
- BALLAST: Condition of Ballast fan [rotational speed ]
Page 5
- C-MIRROR: Condition of Synthetic Mirror fan [rotational speed ]
Page 5
- DMD-EXST : Condition of DMD Exhaust fan [rotational speed ]
Page 5
- C-PRISM : Condition of Color prism fan [rotational speed ]
Page 5
- DMD1 : Condition of DMD-1 fan [rotational speed ]
Page 5
- DMD2: Condition of DMD-2 fan [rotational speed ]
Page 6 - The ON/OFF history of the Lamp 1
Page 7
Page 7
- The ON/OFF history of the L 2amp
5.
SIGNAL LIST Menu
"PRIORITY MODE" item is enabled on the "REGISTERED SIGNAL STATUS".
It becomes easy to recognize an input signal to be a registered signal.
-OFF : Normal mode
-ON : Extended mode signal determination
-OFF : Normal mode
-ON : Extended mode signal determination
PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE
INF-9
4. External Controls
4.1. Control through Serial terminal
SERIAL terminals which are on the side of the projector conform to RS-232C standard. This projector can be controlled
by a PC which is connected as shown below. Also SERIAL OUT terminal is provided to enable plural projector control.
by a PC which is connected as shown below. Also SERIAL OUT terminal is provided to enable plural projector control.
4.1.1 Examples of Connection
4.1.2 Pin Layout and Signal Names for SERIAL Connector
4.1.3 Communication conditions (Factory setting)
Signal Level
RS-232C compliant
Character length
8 bit
Sync. Method
Asynchronous
Stop bit
1 bit
Baud rate
9 600 bps
X parameter
None
Parity
None
S parameter
None
4.1.4 Procedure of Communication Condition Settings
1. Push the menu button and choose sub menu "RS-232C"
of the main menu "projector setup", and please push the
enter button.
2. Press the ▼ or ▲ button to select communication settings.
3. Press the or button to confirm the setting.
4. Press the MENU button three times.
The on-screen indications disappear, and the system returns
to the normal screen.
of the main menu "projector setup", and please push the
enter button.
2. Press the ▼ or ▲ button to select communication settings.
3. Press the or button to confirm the setting.
4. Press the MENU button three times.
The on-screen indications disappear, and the system returns
to the normal screen.
4.1.5 Cable Specifications
< When connected to a computer >
Pin
Signal
name
Contents
①
－
NC
②
RXD Received
data
③
TXD Transmitted
data
④
－
NC
⑤
GND Earth
⑥
－
NC
⑦
RTS
⑧
CTS
Connected internally
⑨
－
NC
Pin
Signal
name
Contents
①
－
NC
②
TXD Transmitted
data
③
RXD Received
data
④
－
ＮＣ
⑤
GND Earth
⑥
－
NC
⑦
CTS
⑧
RTS
Connected internally
⑨
－
NC
Note: Use a proper communication cable which is suitable for the PC to connect SERIAL connector and the PC.
Projector
Computer
(DTE specifications)
(DTE specifications)
PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE
INF-10
4.1.6 Basic Format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order.
Add parameters according to the details of control.
1. Basic control command (without parameter)
2. Basic control command (with parameters)
3. Basic control command (with subcommand)
4. Operation
Specifies the method of processing the value specified by parameters.
Add parameters according to the details of control.
1. Basic control command (without parameter)
2. Basic control command (with parameters)
3. Basic control command (with subcommand)
4. Operation
Specifies the method of processing the value specified by parameters.
Code Description
=
Sets the value specified by the parameter.
_ (under bar)
Adds the value specified by the parameter to the current value.
5. Sign
Specifies positive or negative of the value specified by parameters.
Specifies positive or negative of the value specified by parameters.
Code Description
＋
The value specified by the parameter is a positive value or 0 (zero).
－
The value specified by the parameter is a negative value.
6. Parameters
Specify the setting or adjustment value by right justification (0 is not suppressed).
For example, when the setting value is "1", set it as "00001".
7. ID of the basic control command
This projector will respond to the computer only in the following cases.
-
Specify the setting or adjustment value by right justification (0 is not suppressed).
For example, when the setting value is "1", set it as "00001".
7. ID of the basic control command
This projector will respond to the computer only in the following cases.
-
If the sent ID coincides with the projector ID.
- RESPONSE(ID ALL) in RS232C settings of this projector is ON and the sent ID is ALL.
- Or If Group (A-Z) of the sent ID coincides with GROUP in RS232C settings of this projector and
RESPONSE(ID GROUP) in RS232C settings of this projector is ON.
Specifically, please refer to "SECTION6 (Control Commands)".
8. Response (Callback) of the basic control command
In the period when the command can be accepted.
Differs according to each command.
In the period when commands cannot be accepted.
- Or If Group (A-Z) of the sent ID coincides with GROUP in RS232C settings of this projector and
RESPONSE(ID GROUP) in RS232C settings of this projector is ON.
Specifically, please refer to "SECTION6 (Control Commands)".
8. Response (Callback) of the basic control command
In the period when the command can be accepted.
Differs according to each command.
In the period when commands cannot be accepted.
Hexadecimal
02h 45h 52h 34h 30h 31h 03h
Character E R 4 0 1
In case of the parameter error or REMOTE2 effective.
Hexadecimal
02h 45h 52h 34h 30h 31h 03h
Character E R 4 0 2
9. Attention
- No command may be sent or received for 10 to 60 seconds after the lamp starts lighting. Try sending any
command after that period has elapsed.
- When sending several commands, be sure to wait for a response from the projector, and send the next
command after 0.5 seconds or more pass.
- It might take time by the time the response returns because the command is processed in the projector.
Set the time-out to 10 seconds or longer.
- When it is used a projector of plural stands.
Please set different "ID" every projector.
Only as for one projector, "ON", all remaining projectors please set "RESPONSE(ID ALL)" in "OFF" in
"RESPONSE(ID ALL)".
- No command may be sent or received for 10 to 60 seconds after the lamp starts lighting. Try sending any
command after that period has elapsed.
- When sending several commands, be sure to wait for a response from the projector, and send the next
command after 0.5 seconds or more pass.
- It might take time by the time the response returns because the command is processed in the projector.
Set the time-out to 10 seconds or longer.
- When it is used a projector of plural stands.
Please set different "ID" every projector.
Only as for one projector, "ON", all remaining projectors please set "RESPONSE(ID ALL)" in "OFF" in
"RESPONSE(ID ALL)".
Start (STX)
ID
Separator
(semicolon)
Command
End (ETX)
1 byte
4 bytes
1 byte
3 bytes
1 byte
Start (STX)
ID
Separator
(semicolon)
Command
Separator
(colon)
Parameters End
(ETX)
1 byte
4 bytes
1 byte
3 bytes
1 byte
Undefined
length
1 byte
Start (STX)
ID
Separator
(semicolon)
Command
Separator
(colon)
Subcommand Operation
1 byte
4 bytes
1 byte
3 bytes
1 byte
5 bytes
1 byte
Sign
Parameters End
(ETX)
1 byte
5 bytes
1 byte
Click on the first or last page to see other PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man10) service manuals if exist.