DOWNLOAD Panasonic PT-DZ21K2 / PT-DS20K2 / PT-DW17K2 / PT-DZ16K2 (serv.man2) Service Manual ↓ Size: 74.49 MB | Pages: 109 in PDF or view online for FREE

Model
PT-DZ21K2 PT-DS20K2 PT-DW17K2 PT-DZ16K2 (serv.man2)
Pages
109
Size
74.49 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / 3-CHIP DLP BASED PROJECTOR
File
pt-dz21k2-pt-ds20k2-pt-dw17k2-pt-dz16k2-sm2.pdf
Date

Panasonic PT-DZ21K2 / PT-DS20K2 / PT-DW17K2 / PT-DZ16K2 (serv.man2) Service Manual ▷ View online

PREFACE
< DZ21K2/DS20K2/DW17K2/DZ16K2 >
1. Safety Precautions
  1.1. General Guidelines
For continued safety, no modification of any circuit must be attempted.
Unplug the power cord from the power outlet before disassembling this projector.
Use correctly the supplied power cord and must ground it.
It is advisable to use an isolation transformer in the AC power line before the service.
Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed
and the power supply turned ON.
Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated or damaged
by the short circuit.
After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C
combinations must be properly installed.
After the service, check the leakage current to prevent the customer from getting an electric shock.
  1.2. Leakage Current Check
1. Prepare the measuring circuit as shown in Fig.1.
Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4.  This means that the current must be 0.75mA or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer
because of a possibility of an electric shock.
 Accuracy : 
 2%
 Input resistance :
 1 MΩ
 Input capacitance :
 200 pF
 Frequency range :
15 Hz to 1 MHz
  1.3. UV Precaution and UHM Lamp Precautions
Be sure to unplug the power cord from the power outlet when replacing the lamp.
Because the lamp reaches a very high temperature during its operation, wait until it cools completely when replacing 
the Lamp Unit.
The lamp emits small amounts of UV-radiation, avoid direct-eye contact with the light.
The lamp unit has high internal pressure. If improperly handled, explosion might result.
Because the high pressure lamp involves a risk of failure, never touch the lamp wire lead during the service. 
Performance
 Voltmeter
 (rms reading)
Table. 1
M1
M2
Rs
Rb
Cs
10 kΩ ±0.1%
V
Vb
(V)
0.022μF
±1.0%
to T1
or T2
in FIG.2
Rs:1500 Ω ±0.1%
Cs:0.22μF ±1.0%
Rb:500 Ω ±0.1%
Weighted leakage current = Vb / 500 (A)
M1
M2
T1
T2
Isolation transformer
to power outlet
Measuring
circuit (Fig.1)
Multi Window
Processor
connection
Fig. 1
Fig. 2
5
PREFACE
< DZ21K2/DS20K2/DW17K2/DZ16K2 >
2. Specifications
  2. 1. Specifications
f
The specifications of the projector are as follows.
6
PREFACE
< DZ21K2/DS20K2/DW17K2/DZ16K2 >
  2. 2. Applicable scanning frequency
f
Refer to Operating Instructions “List of compatible signals”  for the types of video signals that can be used with the projector.
For video signal, Y/C signal
Horizontal: 15.73 kHz, Vertical: 59.94 Hz; Horizontal: 15.63 kHz, Vertical: 50 Hz
For RGB signal
Horizontal: 15 kHz to 100 kHz, Vertical: 24 Hz to 120 Hz
PIAS (Panasonic Intelligent Auto Scanning) system
 
f Dot clock frequency: 162 MHz or less
For YC
B
C
R
/YP
B
P
R
 signal
 
f 525i (480i)
Horizontal: 15.73 kHz, Vertical: 59.94 Hz
 
f 525p (480p)
Horizontal: 31.47 kHz, Vertical: 59.94 Hz
 
f 750 (720)/60p
Horizontal: 45 kHz, Vertical: 60 Hz
 
f 1125 (1035)/60i
Horizontal: 33.75 kHz, Vertical: 60 Hz
 
f 1125 (1080)/50i
Horizontal: 28.13 kHz, Vertical: 50 Hz
 
f 1125 (1080)/24sF
Horizontal: 27 kHz, Vertical: 48 Hz
 
f 1125 (1080)/30p
Horizontal: 33.75 kHz, Vertical: 30 Hz
 
f 1125 (1080)/50p
Horizontal: 56.25 kHz, Vertical: 50 Hz
 
f 625i (576i)
Horizontal: 15.63 kHz, Vertical: 50 Hz
 
f 625p (576p)
Horizontal: 31.25 kHz, Vertical: 50 Hz
 
f 750 (720)/50p
Horizontal: 37.5 kHz, Vertical: 50 Hz
 
f 1125 (1080)/60i
Horizontal: 33.75 kHz, Vertical: 60 Hz
 
f 1125 (1080)/24p
Horizontal: 27 kHz, Vertical: 24 Hz
 
f 1125 (1080)/25p
Horizontal: 28.13 kHz, Vertical: 25 Hz
 
f 1125 (1080)/60p
Horizontal: 67.5 kHz, Vertical: 60 Hz
 
f The SYNC/HD and VD terminals do not support 3 value SYNC.
For DVI-D signal
525i (480i)
*1
, 625i (576i)
*1
, 525p (480p), 625p (576p), 750 (720)/60p,  
750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p
 
f Displayable resolution: 640 x 480 to 1 920 x 1 200 (non-interlaced)
 
f Dot clock frequency: 25 MHz to 162 MHz
For HDMI signal
525i (480i)
*1
, 625i (576i)
*1
, 525p (480p), 625p (576p), 750 (720)/60p,  
750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p
 
f Displayable resolution: 640 x 480 to 1 920 x 1 200 (non-interlaced)
 
f Dot clock frequency: 25 MHz to 162 MHz
For SDI signal (Only for 
PT-DZ21K2, PT-DS20K2, 
PT-DZ16K2)
SD-SDI signal
SMPTE ST 259 compliant
YC
B
C
R
 4:2:2 10-bit
480i, 576i
Single link HD-SDI signal
SMPTE ST 292 compliant
YP
B
P
R
 4:2:2 10-bit
720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 
1080/24p, 1080/24sF, 1080/30p
Dual link HD-SDI signal
*2
SMPTE ST 372 compliant
RGB 4:4:4 12-bit/10-bit
1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 
2048 x 1080/24p, 2048 x 1080/24sF
X'Y'Z' 4:4:4 12-bit
2048 x 1080/24p, 2048 x 1080/24sF
3G-SDI signal
SMPTE ST 424 compliant
YP
B
P
R
 4:2:2 10-bit
1080/50p, 1080/60p
RGB 4:4:4 12-bit/10-bit
1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual link 3G-SDI signal
*2
SMPTE ST 425 compliant
YP
B
P
R
 4:4:4 12-bit/10-bit
1080/60p, 1080/50p, 2048 x 1080/60p, 2048 x 1080/50p, 
2048 x 1080/48p
RGB 4:4:4 12-bit/10-bit
1080/60p, 1080/50p, 2048 x 1080/60p, 2048 x 1080/50p, 
2048 x 1080/48p
*1  Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
*2  Only for PT-DZ21K2, PT-DS20K2
Note
 
f DIGITAL LINK input compatible signal is the same as HDMI input compatible signal.
7
PREFACE
< DZ21K2/DS20K2/DW17K2/DZ16K2 >
  2. 3. Terminal
<RGB 1 IN> terminal
1 set (BNC x 5 (RGB/YP
B
P
R
/YC
B
C
R
/YC/VIDEO x 1))
RGB signal
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD
TTL high impedance, automatic positive/negative 
polarity compatible
VD
TTL high impedance, automatic positive/negative 
polarity compatible
YP
B
P
R
 signal
Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
Y/C signal
Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω
VIDEO signal
1.0 V [p-p] 75 Ω
<RGB 2 IN> terminal
1 set, high-density D-Sub 15 p (female)
RGB signal
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD
TTL high impedance, automatic positive/negative 
polarity compatible
VD
TTL high impedance, automatic positive/negative 
polarity compatible
YP
B
P
R
 signal
Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
<DVI-D IN> terminal
1 set, DVI-D 24 p, single link, DVI 1.0 compliant, HDCP compatible
<HDMI IN> terminal
1 set, HDMI 19 p, HDCP compatible, Deep Color compatible
<SDI IN 1> terminal (Only for 
PT-DZ21K2, PT-DS20K2)
<SDI IN> terminal (Only for 
PT-DZ16K2)
1 set (BNC)
SD-SDI signal
SMPTE ST 259 compliant
HD-SDI signal
SMPTE ST 292 compliant
3G-SDI signal
SMPTE ST 424 compliant
Dual link HD-SDI 
(LINK-A) signal
*1
SMPTE ST 372 compliant
Dual link 3G-SDI (Link 
1) signal
*1
SMPTE ST 425 compliant
<SDI IN 2> terminal
(Only for PT-DZ21K2, 
PT-DS20K2)
1 set (BNC)
SD-SDI signal
SMPTE ST 259 compliant
HD-SDI signal
SMPTE ST 292 compliant
3G-SDI signal
SMPTE ST 424 compliant
Dual link HD-SDI 
(LINK-B) signal
SMPTE ST 372 compliant
Dual link 3G-SDI (Link 
2) signal
SMPTE ST 425 compliant
<3D SYNC 1 IN/OUT> terminal
(Only for PT-DZ21K2, 
PT-DS20K2)
1 set (BNC)
During input setting
TTL high impedance
During output setting
TTL output: Maximum 10 mA
<3D SYNC 2 OUT> terminal
(Only for PT-DZ21K2, 
PT-DS20K2)
1 set (BNC)
TTL output: Maximum 10 mA
<SERIAL IN>/ <SERIAL OUT> 
terminal
D-Sub 9 p, 1 set each, RS-232C compliant, for computer control
<REMOTE 1 IN>/ <REMOTE 1 
OUT> terminal
M3 stereo mini jack, 1 set each, for remote control (wired)/for projector connection control
<REMOTE 2 IN> terminal
1 set, D-Sub 9 p, for contact control
<DIGITAL LINK/LAN> terminal
1 set, RJ-45, for network and DIGITAL LINK connections, PJLink compatible, 100Base-TX, Art-Net 
compatible
*1  Only for PT-DZ21K2, PT-DS20K2
Note
 
f The model numbers of accessories and optional accessories are subject to change without prior notice.
8
Page of 109
Display

Click on the first or last page to see other PT-DZ21K2 / PT-DS20K2 / PT-DW17K2 / PT-DZ16K2 (serv.man2) service manuals if exist.