DOWNLOAD Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) Service Manual ↓ Size: 524.22 KB | Pages: 14 in PDF or view online for FREE

Model
PT-DZ16KU PT-DZ16KE PT-DS16KD (serv.man3)
Pages
14
Size
524.22 KB
Type
PDF
Document
Service Manual / Other
Brand
Device
Projector / 3-CHIP DLP BASED PROJECTOR
File
pt-dz16ku-pt-dz16ke-pt-ds16kd-sm3.pdf
Date

Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) Service Manual / Other ▷ View online

SECTION 3  ADJUSTMENTS
<PT-DZ16K>
  1. 4. EEPROM data transfer
* The EEPROM data transfer via LAN terminal or serial terminal.
    1. 4. 1. Equipment to be used
1. Computer : Use it for the transfer of backup data.
2. Communication cable
・ Case of serial terminal connection : D-sub 9pin (male/female RS-232C straight)
・ Case of LAN terminal connection : LAN cable. (When connecting directly, use a cross cable)
3. Service Software : [DataLogBackup.exe] Service software is downloaded from the projector service homepage.
    1. 4. 2. Connection preparations
1. In the case of serial terminal connection
・ Confirm the RS-232C settings (ID, Baudrate  and Parity) and take a note.
2. In the case of LAN terminal connection
・ Confirm the network IP address of the projector and take a note.
・ Set the IP address of computer to approximate value of projector IP address.
3. Connect the projector and the PC by using a communication cable.
[Note]
Set up your computer not to standby or shutdown.
Serial terminal connection
LAN terminal connection
ADJ - 4
    1. 4. 3. Backup the EEPROM data (It is before circuit board exchange)
1. Switch the projector to "Normal-Standby" mode (POWER indicator is Lighting in red).
2. Start up service software [DataLogBackup.exe] with a computer.
3. 1) Select "Option " → " Setting".
    2) Select the connection method, enter the setting information of the projector.
ADJ - 4
SECTION 3  ADJUSTMENTS
<PT-DZ16K>
4. Select a model number and ID.
5. 1) Select "Backup (EEPROM)”.
    2) Checkmark in "REPLACE A-PWB" of "COPY MODE".
    3) Click an [READ EEPROM] button.
ADJ - 5
6. Select the save place and click the [Save(S)] button.
7. When the progress bar reaches the right-side end, the read of data is completion.
    ("WRITE EEPROM" button and "READ EEPROM" button will return to normal display from gray.)
    Select "File" ⇒ "Quit", please exit.
ADJ - 5
SECTION 3  ADJUSTMENTS
<PT-DZ16K>
    1. 4. 4. Restore the backup EEPROM Data (After circuit board exchange)
1. Switch the projector to "Normal-Standby" mode (POWER indicator is Lighting in red).
2. Start up service software [DataLogBackup.exe] with a computer.
3. Select "Option " → " Setting" and select the connection method, enter the setting information of the projector.
4. Select a model number and ID.
5. 1) Choose "Backup" (an EEPROM).
    2) Checkmark in "REPLACE A-PWB" of "COPY MODE".
    3) Click an [WRITE EEPROM] button.
6. Select the file and click the [OPEN(O)] button.
ADJ - 6
7. When the progress bar reaches the right-side end, the write of data is completion.
    ("WRITE EEPROM" button and "READ EEPROM" button will return to normal display from gray.)
    Select "File" ⇒ "Quit", please exit.
8. When to turn off the main power and turned on again, the setting is complete.
ADJ - 6
SECTION 3  ADJUSTMENTS
<PT-DZ16K>
  1. 5. Model Information Setup
1. Setting to service mode and select sub menu "MODEL"
    of main menu "EXTRA OPTION".
2. Select a model and push the “ENTER” button.
3. When to turn off the main power and turned on again, 
    the setting is complete.
  1. 6. Clog sensor calibration
1. Setting to Service mode and select sub menu "CLOG SENSOR CALIBRATION" of main menu "EXTRA OPTION".
2. Select the meters above the sea level of the work place and push the "ENTER" button.
* After completing the "EEPROM data transfer", Please carry out.
* This operation should be done with the main body is completely assembled and set on the floor and the adjuster
   legs are set in the main body.
* Please replace with a new air filter before starting calibration.
* Please calibration at a location where there are no heat apparatus and supply opening of the air-conditioner.
3. When [ OK ] is selected and ENTER button is pressed, the calibration is executed.
・ When the calibration is started, the screen becomes whole magenta.
・ While calibrating, all lamps will light (QUAD mode).
・ Do not shut down the power of projector during the calibration.
・ The progress is shown at the left top portion of the display with % unit.
4. When the magenta screen will disappear in approx 30 minutes and it returns to the normal screen, 
    the calibration is completed.
    Turn the POWER switch OFF and turn ON it again, then confirm whether to operate normally.
30 %
ADJ - 7
Page of 14
Display

Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) Service Manual / Other ▷ Download

  • DOWNLOAD Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) Service Manual ↓ Size: 524.22 KB | Pages: 14 in PDF or view online for FREE
  • Here you can View online or download the Service Manual / Other for the Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) Projector. Information contained in Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man3) Service Manual / Other (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.