DOWNLOAD Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man14) Service Manual ↓ Size: 4.01 MB | Pages: 38 in PDF or view online for FREE

SECTION 1  SERVICE  INFORMATION

<PT-DZ16K>

  9. MODEL

Set this when the A-P.C.Board is replaced.
  * If you can copy EEPROM data from the old A-P.C.Board, this setting is unnecessary.
  * This model setting is changed after turn power on and off.

10. CLOG SENSOR CALIBRATION

Proofreading the blocking detect circuit.
  * Execute this after EEPROM（IC3509/IC3518）/A-P.C.Board or clogging sensor (M2-P.C.Board） is replaced.
  * Please refer to Clause 1 of SECTION 3 (Adjustments) for the procedure.

11. LAMP COOLING MODE

Setting of the fan operation for lamp cooling time. 
 - FAN STOP : Lamp fan is stopped at the lamp cooling time.
 - FAN ROTATION : Lamp fan is rotated at the lamp cooling time.

12. SMOKE FILTER DISPLAY

Setting of the self-diagnosis display (U75) at the time of smoked cut-off filter use. 
  - ON : Warning is displayed.
  - OFF : Warning is not displayed.

  1. [PICTURE] menu

「

AI WINDOW」 is added to the setting of the sub menu "dynamic iris".

    - AI WINDOW: Sets the APL detection area. Please set AI MODE to "AUTO" usually.

  2. [POSITION] menu

「

DVI EQUALIZER」 is added to a sub menu.

    - DVI EQUALIZER: If noise appears when DVI input, sets the value so that the noise decreases.
      Please set to "AUTO" usually.

INF - 11

      Please set to  AUTO  usually.

  3. [DISPLAY OPTION] menu

The following items are added to setting of sub menu "SDI IN".
「

XYZ TO RGB SETTING」

    - FACTORY SETTING: Uses the value of FACTORY Yxy conversion factor to the original data of XYZ → RGB.

    (Default)

    - MEASURED: Uses the value of MEASURED Yxy conversion factor to the original data of XYZ → RGB.
    - REC709: Uses the value of REC709 Yxy conversion factor to the original data of XYZ  → RGB.
    - DCI P3: Uses the value of DCI P3 Yxy conversion factor to the original data of XYZ  → RGB.
「

XYZ TEST PATTERN」

    - WHITE：10%～100%
    - DARK GRAY：1～10
    - COLOR：Red/Green/Blue/Cyan/Magenta/Yellow    1～2

  4. [PROJECTOR SETUP] menu

「

MAX AVAILABLE LAMPS」 is added to a sub menu.

Sets the maximum number of lamps that can be used. Please set to "4" normally.

「

DETAILED INFORMATION」 is displayed by pressing the "ENTER" button on the  「BRIGHTNESS CONTROL」 screen.

The detailed information of brightness control can be checked. 

「

SHUTTER COUNTER」 is added to setting of the sub menu "INITIALIZE".

When the mechanical shutter is replaced, initialize the shutter counter.

The following items are added to an indication screen of the sub menu "STATUS ".
  1) Page 2

- BALLAST VERSION

Ballast software version

  2) Page 3

- HORIZONTAL TILT

Horizontal angle

INF - 11

SECTION 1  SERVICE  INFORMATION

<PT-DZ16K>

  3) Page 4

- MAIN PROGRAM BANK1/2 Program bank is "ACTIVE" indication during behavior
- MAIN VERSION

Main Microcomputer Software Version

- FPGA VERSION

FPGA software version

- BMP VER.

Version of BitMap data

- ENG～JPN VER.

Version of the each font data (Chinese/Japanese/Korean/English/Russian)

  4) Page 5

- FM R/FM G/FM B VERSIONVersion of the each Formatter Software Version

(Configuration/Main Application/Sequence/De-Gamma)

  5) Page 6

- TEMP（℃）

Intake air temperature / Exhaust air temperature / Optical module temperature

- P.SENSOR

Brightness Sensor value

- VOLT

Voltage of LAMP1/LAMP2/LAMP3/LAMP4

- AIR FLOW

Sensor value / AD conversion value, Sensor Correction value/ AD conversion value,
Threshold / Margin

- MODE

FAN control mode

- CLOG

Information of rev up fan by the blocking of the air filter

- EX1/EX2/EX3/EX4

Exhaust1-4 fan status [Rotational speed]

- IN1/IN2

Intake1-2 fan status [Rotational speed]

- L1/L2/L3/L4

Lamp1-4 fan status [Rotational speed]

- B1/B2

Ballast1-2 fan status [Rotational speed]

- POW

Power fan status [Rotational speed]

- CASE

Signal block fan status [Rotational speed]

- L-L/L-R

Lamp-L/Lamp-R fan status [Rotational speed]

- PRI1/PRI2/PRI3

Color prism1-3 fan status [Rotational speed]

INF - 12

p

[

p

]

- PUMR/PUMG/PUMB

Liquid cooling pump-R/G/B status [Rotational speed]

  6) Page 7

Information of SDI signal. (when information cannot show, "-" is displayed)
- MODE

Mode (「NO SIGNAL」,「SD-SDI」,「HD-SDI」,「3G-SDI」)

- TRANSPORT

Conversion method (「PROGRESSIVE」,「INTERLACED」)

- PICTURE

Picture information (「PROGRESSIVE」,「INTERLACED」)

- RATE

Rate information (「23.98」,「24」,「25」,「29.97」,「30」,「50」,「59.94」,「60」)

- SAMPLING

Sampling information

- BIT DEPTH

Bit depth

  7) Page 8～11

History of lighting / lights out of the lamp1-4.

  5. [TEST PATTERN] menu

The following test patterns are added.

- Checker pattern

- Focus (background 70% gray) pattern

- Inverted checker pattern

INF - 12

SECTION 1  SERVICE  INFORMATION

<PT-DZ16K>

Pin

Pin

(1)

(1)

(2)

(2)

(3)

(3)

(4)

(4)

(5)

(5)

(6)

(6)

(7)

(7)

GND

 Earth

－

 NC

 NC

RXD

 Received data

TXD

 Transmitted data
 NC

Signal name

－

－

RTS

－

 NC

CTS

TXD

 Transmitted data

RXD

 Received data

－

 ＮＣ

GND

 Earth

SERIAL terminals which are on the side of the projector conform to RS-232C standard. This projector can be controlled

by a PC which is connected as shown below. Also SERIAL OUT terminal is provided to enable plural projector control.

Details

Signal name

Details

－

 NC

Note : Interface cable is not a standard accessory.

D-Sub 9-pin (female)

Outside view

D-Sub 9-pin (male)

Outside view

INF - 13

(7)

(7)

(8)

(8)

(9)

(9)

1. Press MENU button of main body or remote controller.
   

Go to Main menu --> Projector setup. In sub menu,

    select "RS-232C" and press ENTER.
2. Select communication condition by pressing   ▲ ▼ button.
    Set it with pressing      button.
3. Press MENU button 3 times and return to regular display.

When connected to a computer

When multiple projectors are connected

NC

NC

NC

NC

NC

NC

NC

NC

NC

NC

NC

NC

 NC

 Connected internally

CTS

－

 NC

RTS

CTS

 Connected internally

RTS

－

3

1
2
3

　

Stop bit

　

X parameter

　

Signal level

　

Sync. Method

　

Baud rate

　

Parity

　

8 bits

　

1 bit

　

None

　

None

　

S parameter

　

RS-232C-compliant

　

Asynchronous

　

9 600 bps

　

None

　

Character length

6
7

5

1
2

6
7

4
5

5

1

6

6

Projector

<SERIAL IN> terminal

C

omputer

 (D

TE 

specifications)

Projector 1

<SERIAL O

U

T> terminal

2

4

8

8

Projector 2

<SERIAL IN> terminal

2

3

3

4

4

5

7

7

8

8

1

NC

NC

NC

NC

9

<

9

9

9

INF - 13

SECTION 1  SERVICE  INFORMATION

<PT-DZ16K>

 

Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order.
Add parameters according to the details of control.

1. Basic control command (without parameter)

2. Basic control command (with parameters)

3. Basic control command (with sub command)

4. Operation

Specifies the method of processing the value specified by parameters.

　

Description

　

Sets the value specified by the parameter.

　

Adds the value specified by the parameter to the current value.

5. Sign

Specifies positive or negative of the value specified by parameters.

Code

=

End

(ETX)

1 byte

4 byte

Undefined length

3 byte

_( underbar)

1 byte

1 byte

1 byte

5 byte

1 byte

Parameter

Sign

1 byte

1 byte

4 byte

1 byte

3 byte

Start

(STX)

ＩＤ

Separator

(semicolon)

Command

Separator

(semicolon)

Command

Separator

(semicolon)

Start

(STX)

3 byte

1 byte

1 byte

1 byte

4 byte

1 byte

ＩＤ

Command

Start

(STX)

ＩＤ

End

(ETX)

End

(ETX)

Separator

(colon)

Separator

(colon)

Parameter

Parameter

Operation

5 byte

1 byte

INF - 14

Specifies positive or negative of the value specified by parameters.

　

Description

　

The value specified by the parameter is a positive value or 0 (zero).

　

The value specified by the parameter is a negative value.

6.　Parameters

Specify the setting or adjustment value by right justification (0 is not suppressed).
For example, when the setting value is "1", set it as "00001".

7. ID of the basic control command

This projector will respond to the computer only in the following cases.
    - If the sent ID coincides with the projector ID.
    - RESPONSE(ID ALL) in RS232C settings of this projector is ON and the sent ID is ALL.
    - Or If Group (A-Z) of the sent ID coincides with GROUP in RS232C settings of this projector and
       RESPONSE(ID GROUP) in RS232C settings of this projector is ON.
Specifically, please refer to a separate volume "Control Commands". 

8. Response (Callback) of the basic control command

In the period when the command can be accepted.

Differs according to each command.

In the period when commands cannot be accepted.

In case of the parameter error or REMOTE2 effective.

52h

32h

03h

Character

1

Character

E

R

02h

45h

34h

30h

4

0

Hexadecimal

30h

31h

02h

45h

Hexadecimal

03h

E

R

4

0

2

－

52h

Code

＋

34h

INF - 14