DOWNLOAD Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man12) Service Manual ↓ Size: 5.17 MB | Pages: 24 in PDF or view online for FREE

Model
PT-DZ16KU PT-DZ16KE PT-DS16KD (serv.man12)
Pages
24
Size
5.17 MB
Type
PDF
Document
Service Manual / Other
Brand
Device
Projector / 3-CHIP DLP BASED PROJECTOR
File
pt-dz16ku-pt-dz16ke-pt-ds16kd-sm12.pdf
Date

Panasonic PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man12) Service Manual / Other ▷ View online

SECTION 2  DISASSEMBLY  PROCEDURES
<PT-DZ16K>
8. Unscrew the 15 screws and remove the Terminal plate. 
XYN3+F8FJ : 4
XQN2+B5FJ : 2
XTB3+8JFJ : 4
THEC084N : 4
XYN26+C6FJ : 1
9. Unscrew the 5 screws and remove the A-P.C.Board. 
THEC084N
XYN3+F8FJ
XYN3+F8FJ
XTB3+8JFJ
XQN2+B5FJ
XYN26+C6FJ
Terminal plate
XYN3+F8FJ
A-P.C.Board
DIS-8
  2. 4. Removal of Ballast block <B-P.C.Board>
1. Remove the Upper Case according to the section 2.2 "Removal of Upper Case".
2. Unscrew the 5 screws and release the Ballast block.
* In this state, because the lamp cable is connected, ballast block does not come off.
A P.C.Board
XYN3+F8FJ
Ballast block
DIS-8
SECTION 2  DISASSEMBLY  PROCEDURES
<PT-DZ16K>
3. Unscrew the 6 screws and remove the Ballast mesh. 
4. Unplug the lamp cable connector(CN3) of each B-P.C.Board, and then remove the ballast block.
5. Unscrew the 6 screws and open up the Ballast case 2. 
XYN3+F6FJK
Ballast mesh
B-
P.C
.B 1
B-
P.C
.B 2
B-
P.C
.B 4
B-
P.C
.B 4
< Ballast block >
CN3 Connector
Ballast block
DIS-9
p
p
6. Unscrew the each 2 screws and remove the B-P.C.Board. 
XYN3+F8FJ
XYN4+F32FJ
Ballast case 2
Note that the claw portion of ballast case 2, 
have stuck in the ballast fan.
Ballast case 2
XTW3+8PFJ
B-P.C.B 1
B-P.C.B 3
XTW3+8PFJ
B-P.C.B 2
B-P.C.B 4
DIS-9
SECTION 2  DISASSEMBLY  PROCEDURES
<PT-DZ16K>
  2. 5. Removal of Power supply block <PC1/PC2 -P.C.Board>
1. Remove the Upper Case according to the section 2.2 "Removal of Upper Case".
2. Remove the Signal processing block according to the steps 1 through 3 in the section
    2.3 "Removal of Signal processing block".
3. Pull out the Ballast block according to the steps 1 through 2 in the section 2.4 "Removal of Ballast block".
    Spread the insulator on top of the main unit, place the ballast blocks on top of it.
4. Unscrew the 3 screws and remove the Partition 1 and Partition 2. 
Ballast block
Insulator
Partition 1
* The overlap is the power-block
side is a Partition 1.
DIS-10
5. Unscrew the 3 screws and remove the Power fan block.
XYN3+F8FJ
Partition 2
XYN3+F8FJ
Power fan block
Partition 1
Partition 2
* The overlap is the power-block
side is a Partition 1.
DIS-10
SECTION 2  DISASSEMBLY  PROCEDURES
<PT-DZ16K>
6. Unscrew the 8 screws and remove the Power shield case.
* Unscrew the 1 screw and remove the K-P.C.Board.
7. Unscrew the 1 screw and pull out the clamp of two, remove the Power cover sheet.
XYN3+F8FJ
K-P.C.Board
XYN3+F8FJ
Power shield case
DIS-11
8. Unscrew the each 4 screws and remove the PC block. 
XYN3+F8FJ
Clamp
Power cover sheet
Pinch the portion of the arrow with
needle-nose pliers, and pull out in
an upward direction.
XYN3+F8FJ
PC1 block
PC2 block
DIS-11
Page of 24
Display

Click on the first or last page to see other PT-DZ16KU / PT-DZ16KE / PT-DS16KD (serv.man12) service manuals if exist.