DOWNLOAD Panasonic ET-YFB200G Service Manual ↓ Size: 25.93 MB | Pages: 37 in PDF or view online for FREE

SAFETY PRECAUTIONS

< YFB200G >

 Accuracy : 

≦

 2%

 Input resistance :

≧

 1 MΩ

 Input capacitance :

≦

 200 pF

 Frequency range :

15 Hz to 1 MHz

Table. 1

1. Prepare the measuring circuit as shown in Fig.1.
    Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4.  This means that the current must be 0.75mA
    or less.
6. If the reading is out of the above standard, the device must be repaired and rechecked before returning to the
    customer because of a possibility of an electric shock.

- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this device.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this device when you service with the upper
  case removed and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated
  or damaged by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation
  R-C combinations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.

Performance

 Voltmeter
 (rms reading)

M1

M2

Rs

Rb

Cs

10 kΩ ±0.1%

V

Vb

(V)

0.022μF
±1.0%

to T1
or T2
in FIG.2

Rs:1500 Ω ±0.1%
Cs:0.22μF ±1.0%
Rb:500 Ω ±0.1%

Weighted leakage current = Vb / 500 (A)

M1

M2

T1

T2

Isolation transformer

to power outlet

Measuring
circuit (Fig.1)

Multi Window

Processor

connection

Fig. 1

Fig. 2

4

SPECIFICATIONS

< YFB200G >

f

r Terminal

2 sets, high-density D-Sub 15 p (female)

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)

HD/SYNC

TTL high impedance, automatic positive/negative 
polarity compatible

VD

TTL high impedance, automatic positive/negative 
polarity compatible

(HD/SYNC and VD do not support 3 value SYNC.)

Y: 1.0 V [p-p] including synchronization signal, P

B

P

R

: 0.7 V [p-p] 75 Ω

Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω

1 set, Pin jack 1.0 V [p-p] 75 Ω

2 sets, HDMI 19 p, HDCP compatible, Deep Color compatible
Audio signal: Linear PCM (sampling frequency: 48 kHz/44.1 kHz/32 kHz)

1 set, 3-pin 3.5 mm detachable terminal block, for external control (RS-232C compliant)

3 sets, M3 stereo mini jack 0.5 V [rms], input impedance 22 kΩ or higher

1 set, M3 stereo mini jack (monitor output, stereo can be supported)
0 V [rms] to 2.0 V [rms] (variable), output impedance 2.2 kΩ or lower

1 set, DVI-D 24 p

1 set, RJ-45, for network connection, PJLink compatible, 10Base-T/100Base-TX

2 sets, RJ-45, for DIGITAL LINK connection (HDBaseT

TM

 compliant)

1 set, D-Sub 9 p, for external control (contact control)

*1  Only the <COMPUTER 1 IN> terminal can input Y/C signal using the optional D-SUB - S Video conversion cable (Model No.: ET-ADSV).

5

SPECIFICATIONS

< YFB200G >

r Applicable scanning frequency

For details of the video signal supported by this device, refer to Operating Instructions “Compatible signals”.

Horizontal 15.73 kHz, Vertical 59.94 Hz (NTSC/NTSC4.43/PAL-M/PAL60)
Horizontal 15.63 kHz, Vertical 50 Hz (PAL/PAL-N/SECAM)

Horizontal 15.6 kHz to 98.8 kHz, Vertical 24.0 Hz to 120.0 Hz

 

f Dot clock frequency: 13.5 MHz to 162.0 MHz

 

f 525i (480i)

Horizontal 15.73 kHz, Vertical 59.94 Hz

 

f 525p (480p)

Horizontal 31.47 kHz, Vertical 59.94 Hz

 

f 750 (720)/60p

Horizontal 45.0 kHz, Vertical 60 Hz

 

f 1125 (1080)/60i

Horizontal 33.75 kHz, Vertical 60 Hz

 

f 1125 (1080)/25p

Horizontal 28.13 kHz, Vertical 25 Hz

 

f 1125 (1080)/24sF

*1

Horizontal 27.0 kHz, Vertical 48 Hz

 

f 1125 (1080)/60p

Horizontal 67.5 kHz, Vertical 60 Hz

 

f 625i (576i)

Horizontal 15.63 kHz, Vertical 50 Hz

 

f 625p (576p)

Horizontal 31.25 kHz, Vertical 50 Hz

 

f 750 (720)/50p

Horizontal 37.5 kHz, Vertical 50 Hz

 

f 1125 (1080)/50i

Horizontal 28.13 kHz, Vertical 50 Hz

 

f 1125 (1080)/24p

Horizontal 27.0 kHz, Vertical 24 Hz

 

f 1125 (1080)/30p

Horizontal 33.75 kHz, Vertical 30 Hz

 

f 1125 (1080)/50p

Horizontal 56.25 kHz, Vertical 50 Hz

525i (480i)

*2

, 625i (576i)

*2

, 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 1125 (1080)/60i, 1125 

(1080)/50i, 1125 (1080)/60p, 1125 (1080)/50p, 1125 (1080)/24p, 1125 (1080)/24sF

*1

, 1125 (1080)/25p, 

1125 (1080)/30p

 

f Displayable resolution: VGA (640 x 480) to WUXGA (1 920 x 1 200), VESA CVT-RB (Reduced Blanking) 

compliant

 

f Dot clock frequency: 25.2 MHz to 162.0 MHz

 

f 720/60p (1 280 x 720)

Horizontal 45.0 kHz, Vertical 60.0 Hz

 

f 1080/24p (1 920 x 1 080)

Horizontal 27.0 kHz, Vertical 24.0 Hz

 

f 1080/30p (1 920 x 1 080)

Horizontal 33.8 kHz, Vertical 30.0 Hz

 

f 1080/50p (1 920 x 1 080)

Horizontal 56.3 kHz, Vertical 50.0 Hz

 

f 1280 x 800 (1 280 x 800)

Horizontal 49.7 kHz, Vertical 59.8 Hz

 

f SXGA+ (1 400 x 1 050)

Horizontal 65.2 kHz, Vertical 60.0 Hz

 

f 720/50p (1 280 x 720)

Horizontal 37.5 kHz, Vertical 50.0 Hz

 

f 1080/25p (1 920 x 1 080)

Horizontal 28.1 kHz, Vertical 25.0 Hz

 

f 1080/60p (1 920 x 1 080)

Horizontal 67.5 kHz, Vertical 60.0 Hz

 

f XGA (1 024 x 768)

Horizontal 48.4 kHz, Vertical 60.0 Hz

 

f 1366 x 768 (1 366 x 768)

Horizontal 47.7 kHz, Vertical 59.8 Hz

 

f WUXGA (1 920 x 1 200)

*4*5

Horizontal 74.0 kHz, Vertical 60.0 Hz

 

f Dot clock frequency: 65.0 MHz to 154.0 MHz

*1  Does not support the frame lock.
*2  Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
*3  The supported output signal for the <DIGITAL LINK OUT 1> terminal/<DIGITAL LINK OUT 2> terminal is same as the <DVI-D OUT> terminal. 

However, output of 3D signal is supported only by the <DIGITAL LINK OUT 1> terminal/<DIGITAL LINK OUT 2> terminal, and it is not supported by 
the <DVI-D OUT> terminal.

*4  VESA CVT-RB (Reduced Blanking) compliant
*5 

AL LINK is supporting the long reach communication method, it is not 

supporting the output.

6

SPECIFICATIONS

< YFB200G >

f

Unit : mm

r When mounting a rack

250 (9-27/32")

Front

Front

(465 (18-5/16"))

44 (1-23/32")

482 (18-31/32")

31.8 (1-1/4")

7 (9/32")

127.5 (5-1/32")

10.3 (13/32")

210 (8-9/32")

127.5 (5-1/32")

r When placing on a desk or a shelf

Front

Front

250 (9-27/32")

44 (1-23/32")

(52 (2-1/16"))

8 (8-5/16")

20 (25/32")

170 (6-11/16")

197.2 (7-3/4")

37 (1-15/32")

7