Panasonic DP-8020E / DP-8020P / DP-8016P (serv.man2) Service Manual ▷ View online
53
SEP 2006
Ver. 1.1
DP-8020E/8020P/8016P
Note:
When reinstalling the ADF Rear Cover (1701),
make sure to properly route the ADF Harness as
illustrated.
make sure to properly route the ADF Harness as
illustrated.
(17) Remove 1 Screw (X6).
(18) Remove the ADF PC Board Cover (1916).
(18) Remove the ADF PC Board Cover (1916).
(19) Release the Clamp from ADF Unit.
Note:
Do not cut the Tie-Wrap. Push the release clip on
the side of the clamp to remove it.
the side of the clamp to remove it.
(20) Disconnect the ADF Harness (2827) on the ADF
PC Board (CN21).
(21) Remove 2 Silver Screws (B1).
(22) Remove 2 Angle Plate (1801).
(22) Remove 2 Angle Plate (1801).
54
SEP 2006
Ver. 1.1
DP-8020E/8020P/8016P
(23) Open the ADF Unit.
(24) Remove 4 Screws (6A).
(24) Remove 4 Screws (6A).
Caution:
Don’t close the ADF Unit subsequent to this step.
(25) Remove the ADF Unit.
(26) Disconnect 5 Harnesses (2848, 2849, 2850,
2851) on the ADF PC Board. (5 connectors)
(27) Remove 2 Screws (X6).
(28) Remove the ADF PC Board (2846).
(28) Remove the ADF PC Board (2846).
(29) Release the Harness from the Clamp.
(30) Disconnect 2 Harnesses (2848, 2850).
(31) Remove 7 Screws (X6).
(32) Remove the Motor Bracket (1906) Assembly.
(30) Disconnect 2 Harnesses (2848, 2850).
(31) Remove 7 Screws (X6).
(32) Remove the Motor Bracket (1906) Assembly.
Note:
When reassembling the Motor Bracket (1906)
Assembly, follow the step sequence as illustrated.
Assembly, follow the step sequence as illustrated.
55
SEP 2006
Ver. 1.1
DP-8020E/8020P/8016P
(33) Remove 2 Screws (18).
(34) Remove the ADF Motor (1905).
(34) Remove the ADF Motor (1905).
(35) Remove 2 Drive Belts (1911, 1912).
(36) Remove the S27 Pulley (1910).
(37) Remove the Snap Ring (B9).
(38) Remove the S27 Pulley (1910).
(37) Remove the Snap Ring (B9).
(38) Remove the S27 Pulley (1910).
(39) Release the clips, and remove the Switch
(1918).
(40) Remove the Bushing (698).
Note:
Apply Molykote EM-50L Grease to 3 shafts on the
Right Bracket (1914).
Right Bracket (1914).
56
SEP 2006
Ver. 1.1
DP-8020E/8020P/8016P
<Turn the ADF upside down>
(41) Detach the Hook, and Loop Fastener on the left
side of the Scanning Pad (1822).
(42) Remove 1 Screw (X6).
(43) Remove the Exit 1 Roller (1812), and P6L8
(43) Remove the Exit 1 Roller (1812), and P6L8
Bushing (1813).
<Return the ADF to its upright position>
(44) Release 2 Latch Hooks.
(45) Remove the ADF Front Cover (1702).
(45) Remove the ADF Front Cover (1702).
(46) Release the Harnesses (2849, 2851) from the
Clamp.
(47) Remove 5 Screws (X6).
(48) Remove the Original Tray.
(48) Remove the Original Tray.
(49) Remove the Timing Actuator (2004).
Click on the first or last page to see other DP-8020E / DP-8020P / DP-8016P (serv.man2) service manuals if exist.