Panasonic TX-P55ST60B / TX-P55ST60Y / TX-PR55ST60 Service Manual ▷ View online
21
8 Service Fixture & Tools
8.1.
SC jig
Purpose:
To find the failure board (SC or SU/SD) when the power LED is blinking 7 times.
SC jig:
Jumper connector to connect to SC50 connector on SC board
Part number:
TZSC09187
How to use:
Caution: Remove SC jig from SC board after inspection.
To find the failure board (SC or SU/SD) when the power LED is blinking 7 times.
SC jig:
Jumper connector to connect to SC50 connector on SC board
Part number:
TZSC09187
How to use:
Caution: Remove SC jig from SC board after inspection.
1. Remove the 2 VFG screws from SU and SD board.
2. Remove all connector between SC board and SU/SD board to isolate SC board from both SU and SD board electrically.
2. Remove all connector between SC board and SU/SD board to isolate SC board from both SU and SD board electrically.
Note: The board will be damaged if all connector is not removed (for example; remove connector only for SU board and stay
connecting with SD board. The board will be damaged.)
connecting with SD board. The board will be damaged.)
3. Connect SC jig to connector SC50 at left bottom side of SC board
4. Turn on the TV/Display Unit and confirm the power LED blinking.
4. Turn on the TV/Display Unit and confirm the power LED blinking.
LED blinking: Possible cause of failure is in SC board
No LED blinking (Lighting or no lighting): Possible cause of failure is in SU or SD board
No LED blinking (Lighting or no lighting): Possible cause of failure is in SU or SD board
5. After inspection, turn off the TV/Display Unit and wait a few minutes to discharge.
6. Remove SC jig from SC board.
6. Remove SC jig from SC board.
Remark: This SC jig can be used for all 2013 Plasma TV and Plasma Display.
22
9 Disassembly and Assembly Instructions
9.1.
Disassembly Flow Chart for the Unit
This is a disassembly chart.
When assembling, perform this chart conversely.
When assembling, perform this chart conversely.
23
9.2.
Disassembly Procedure for the Unit
9.2.1.
Remove the Pedestal stand
1. Remove the Plasma panel section from the servicing
stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
downward.
by a soft cloth) with the Plasma panel surface facing
downward.
2. Remove the screws (
×4 )
3. Slide the Pedestal stand to the downside and remove the
Pedestal stand.
9.2.2.
Remove the Bottom cover
1. Remove the screws (
×4
) and remove the Bottom
cover.
9.2.3.
Remove the AC cord clamper B
1. Remove the screws (
×2
) and remove the AC cord
clamper B.
9.2.4.
Remove the Wi-Fi module
1. Remove the screw (
×1
) and remove the Wi-Fi
module.
9.2.5.
Remove the Bluetooth module
1. Remove the screw (
×1
) and remove the Dongle
cover.
2. Remove the Pin guides (
×2
) and disconnect the BT
connector.
3. Remove the Bluetooth module.
9.2.6.
Remove the Rear cover
1. Remove the screws (
×33 ,
×2 ).
2. Remove the M8 caps (
×4 ).
3. Remove the Rear cover.
24
9.2.7.
Remove the P-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for
discharge from electrolysis capacitors.
discharge from electrolysis capacitors.
1. Unlock the hooks and the tapes to free the cables
2. Disconnect the connectors (P2, P6, P11 and P35).
3. Remove the screws (
2. Disconnect the connectors (P2, P6, P11 and P35).
3. Remove the screws (
×5 ,
×1 ,
×1 )
and
remove
the P-Board.
9.2.8.
Remove the A-Board
1. Unlock the hooks and the tapes to free the cables.
2. Disconnect the connectors (A1, A6 and A12).
3. Disconnect the USB cable (JK8605).
4. Disconnect the flexible cables (A20, A31, A32 and A33).
5. Remove the screws (
2. Disconnect the connectors (A1, A6 and A12).
3. Disconnect the USB cable (JK8605).
4. Disconnect the flexible cables (A20, A31, A32 and A33).
5. Remove the screws (
×3 ).
6. Remove the Side shield metal and the Bottom shield
metal.
7. Remove the A-Board.
8. Remove the screws (
×2 ).
9. Remove the Heatsink (bottom) and the Thermal pad.
9.2.9.
Remove the Control unit assy
1. Unlock the tape to free the cables.
2. Disconnect the connector (C14).
3. Remove the claws (
2. Disconnect the connector (C14).
3. Remove the claws (
×2
) and remove the Control unit
assy.
9.2.10. Remove the Speaker SQs
1. Unlock the hooks and the tapes to free the cables.
2. Disconnect the Relay connector.
3. Remove the screws (
2. Disconnect the Relay connector.
3. Remove the screws (
×2
each) and remove the
Speaker SQs (L, R).
Click on the first or last page to see other TX-P55ST60B / TX-P55ST60Y / TX-PR55ST60 service manuals if exist.