Panasonic TX-P50VT60Y / TX-PR50VT60 Service Manual ▷ View online
29
9.2.14. Remove the Fan
1. Unlock the hooks and the tapes to free the cables.
2. Remove the screws (
2. Remove the screws (
×3
each).
3. Disconnect the Relay connector and remove the Fans.
9.2.15. Remove the SU-Board
1. Disconnect the flexible cables (SU1, SU2, SU3, SU4 and
SU5) connected to the SU-Board.
2. Disconnect the flexible cable (SU11-SD11) and the bridge
connector (SC41-SU41).
3. Remove the screws (
×2 ,
×1
) and remove the SU-
Board.
9.2.16. Remove the SD-Board
1. Disconnect the flexible cables (SD1, SD2, SD3, SD4 and
SD5) connected to the SD-Board.
2. Disconnect the flexible cable (SU11-SD11) and the bridge
connectors (SC42-SD42 and SC46-SD46).
3. Remove the screws (
×2 ,
×1
) and remove the SD-
Board.
9.2.17. Remove the SC-Board
1. Unlock the tapes to free the cables.
2. Disconnect the connector (SC2).
3. Disconnect the flexible cable (SC20).
4. Remove the screws (
2. Disconnect the connector (SC2).
3. Disconnect the flexible cable (SC20).
4. Remove the screws (
×7
) and remove the SC-Board.
30
9.2.18. Work instructions for the Rubber
sheet for SC-Board
1. Rubber sheets are put between the board and rear cover
for EMC requirement and heat radiation. Confirm rubber
sheets were placed at each portion when assembling as
shown in figure.
sheets were placed at each portion when assembling as
shown in figure.
9.2.19. Remove the SS-Board
1. Disconnect the connector (SS11).
2. Disconnect the flexible cable (SS33).
3. Disconnect the flexible cables (SS52 and SS54).
4. Remove the screws (
2. Disconnect the flexible cable (SS33).
3. Disconnect the flexible cables (SS52 and SS54).
4. Remove the screws (
×5 ,
×3
) and remove the SS-
Board.
9.2.20. Work instructions for the Rubber
sheet for SS-Board
1. Rubber sheets are put between the board and rear cover
for EMC requirement and heat radiation. Confirm rubber
sheets were placed at each portion when assembling as
shown in figure.
sheets were placed at each portion when assembling as
shown in figure.
9.2.21. Remove the SS2-Board
1. Disconnect the flexible cable (SS57).
2. Remove the screws (
2. Remove the screws (
×2
) and remove the SS2-Board.
9.2.22. Remove the USB cable (A-WiFi)
1. Remove the screw (
×1 ).
2. Remove the USB cable (A-WiFi).
31
9.2.23. Remove the Metal bracket bottom
1. Remove the screws (
×4 ,
×2
) and the Metal
bracket bottom.
9.2.24. Remove the K-Board
1. Remove the screws (
×2
) and remove the LED panel
case.
2. Disconnect the connector (K10).
3. Remove the claw (
3. Remove the claw (
×1
) and remove the K-Board.
4. Remove the LED panel.
9.2.25. Remove the Cabinet assy from the
Plasma panel section
1. Remove the Plasma panel section from the servicing
stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
download.
by a soft cloth) with the Plasma panel surface facing
download.
2. Remove the screws (
×15 ).
3. Remove the Cabinet assy from the Plasma panel section.
9.2.26. Remove the Contact metals
1. Remove the screws (
×6 ).
2. Remove the Contact metal side (L, R).
3. Remove the screws (
3. Remove the screws (
×15 ).
4. Remove the Contact metal bottom.
32
9.2.27. Remove the C1-Board
1. Disconnect the flexible cables (CB1, CB2, CB3, CB4 and
CB5).
2. Disconnect the flexible cable (C10).
3. Disconnect the connectors (C14 and C18).
4. Remove the screws (
3. Disconnect the connectors (C14 and C18).
4. Remove the screws (
×4
) and remove the C1-Board.
9.2.28. Remove the C2-Board
1. Disconnect the flexible cables (CB6, CB7, CB8, CB9,
CB10 and CB11).
2. Disconnect the flexible cables (C20, C21 and C26).
3. Disconnect the connectors (C25 and C28).
4. Remove the screws (
3. Disconnect the connectors (C25 and C28).
4. Remove the screws (
×6
) and remove the C2-Board.
9.2.29. Remove the C3-Board
1. Disconnect the flexible cables (CB12, CB13, CB14 and
CB15).
2. Disconnect the flexible cables (C31 and C36).
3. Remove the screws (
3. Remove the screws (
×4
) and remove the C3-Board.
9.2.30. Replace the Plasma panel
Caution:
Remove the Plasma panel section from the servicing
stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
download.
stand and lay on a flat surface such as a table (covered
by a soft cloth) with the Plasma panel surface facing
download.
A new Plasma panel itself without Contact metals is fragile.
To avoid the damage to new Plasma panel, carry a new
Plasma panel taking hold of the Contact metals.
1. Place a carton box packed a new Plasma panel on the
flat surface of the work bench.
2. Open a box and without taking a new Plasma panel.
3. Attach the Cabinet assy and each P.C.Board and so on,
3. Attach the Cabinet assy and each P.C.Board and so on,
to the new Plasma panel.
Click on the first or last page to see other TX-P50VT60Y / TX-PR50VT60 service manuals if exist.